

Control board
Design file for SMBR hardware modules in KiCAD.
- Size
- 56 × 85 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 229
- Nets
- 149
- Pads
- 753
- Tracks, vias
- 1,602, 609
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 20 Aug 2024
- Updated
- 30 Apr 2026
Overview
Control board is an open-source printed circuit board by TrendBit, from the TrendBit/SMBR-hardware repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 56 × 85 mm with 229 parts on 149 nets, routed with 1,602 tracks and 609 vias.
It is built around the RP2040, SN65HVD230DR and AP8802SG, with the DRV8870DDAR, W25Q32JVZPIQ and 74HC14 among its other parts. Its parts include 73 capacitors, 67 resistors, 19 diodes, 18 connectors and 14 ICs. It belongs with the RP2040 boards of this library.
Main components
12RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)SN65HVD230DR
SOP-8CAN TransceiversTokmasAP8802SG
SOIC-8-40℃~+105℃ 1 1A 700kHz 8V~48V Analog、PWM Buck DC-DC SOIC-8 LED Drivers ROHSDiodes IncorporatedLED DriversDRV8870DDAR
HSOP-8-EP-40℃~+125℃ 1 10uA 3.6A 565mΩ Yes HSOP-8-EP Brushed DC Motor Drivers ROHSTexas InstrumentsBrushed DC Motor DriversW25Q32JVZPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 133MHz 2.7V~3.6V 20 Years 32Mbit 3ms SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbondNOR FLASH74HC14
SOP-14-40℃~+85℃ 1.9V、3.98V、4.4V、5.48V、5.9V 100mV、260mV、260mV 20uA 25ns@4.5V,50pF 2V~6V 6 74HC Noise suppression function Schmitt trigger SOP-14 Inverters ROHSJSMSEMIInvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAT24C256C-SSHL-T
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 1MHz 256Kbit 40 Years 5ms Hardware write protection function、Noise suppression function I2C SOIC-8 EEPROM ROHSMicrochip TechnologyEEPROMREF3033AIDBZR
SOT-23-40℃~+125℃@(Ta) 105uVrms 25mA 3.35V~5.5V 3.3V 36uVp-p 50uA 75ppm/℃ Fixed Series ±0.2% SOT-23 Voltage Reference ROHSTexas InstrumentsVoltage ReferenceGZ1608D601TF
0603-55℃~+125℃ 1 200mA 450mΩ 600Ω@100MHz ±25% 0603 Ferrite Beads ROHSSunlordFerrite BeadsRVT1V100M0405
SMD,D4xL5.4mm-40℃~+105℃ 10uF 15mA@120Hz 2000hrs@105℃ 35V 4mm 5.4mm ±20% SMD,D4xL5.4mm Aluminum Electrolytic Capacitors - SMD ROHSROQANGAluminum Electrolytic Capacitors - SMDB5817W
SOD-123-55℃~+150℃ 1A 1mA@20V 20V 450mV@1A Independent SOD-123 Schottky Diodes ROHShongjiachengSchottky Diodes
README
README.mdSMBR - Hardware
This repository contains the documentation for all hardware modules that make up or can be connected to the Smart Modular BioReactor. All designs were made in KiCAD.
General module specification is to which modules should adhere as much as possible is in Specification.md
General system design
All the main modules are built on a similar basis. These are the RP2040 microcontroller, CANBus and development resources (SWD, UART, etc). The individual modules, in turn, add components to this base that correspond to their specific application. For example, in the case of the Control board, this includes motor drivers or electronics that control and monitor fans. The modules communicate with each other via the CAN bus, where a custom protocol is used.
Modules
Interface board
Extension for RPi 4 which adds capabilities for communication and power inputs. Board serves as hub for CAN bus connection to other modules. Modules can be connected via 3 IDC cables or stacking connector on top. Board is connected to RPi via 40 pin connector. Via this connector is Rpi power and communicate with CAN bus transceiver via SPI. I2C can be used to read on board ADC which read board input voltage, current. This board also supplies 5V rail for Rpi and rest of the system. PoE module can be mounted to the board and PoE lines will be passed from RPi header.
Control board
Board responsible for main control function of SMPBR. Can be used to control illumination intensity. Drives peltier element which influence temperature of algae in bottle. Controls Aerator, Peristaltic pump, Mixer and heat control fans on device. Reads temperature of heater plate and LED panel. Can be used as additional CAN bus HUB. Is designed to be stacked on top of Interface module, as third layer of sandwich RPi-Interface-Control.
Sensor board
Module performing most of the basic measurements related to experiment. Consists of three boards which can be connected together around sampling cuvette. Sample is pumped into cuvette and after adaptation the measurements can start. For OJIP measurement sample is saturated with high power 10W Green LED and resulting value is measured with adaptive gain IR energy sensor. Another measurement is optical density which can be measured at 6 defined wavelengths. Board also measures temperature in bottle via two contact-less thermometers (thermopiles).
Illumination board - Basic RGBW
SMPBR illumination panel with 4 channels. Channels can be controlled individually from control module. Each module has own power limit based on on board sense resistor. Board has integrated thermistor in order to limit heat dissipation which could influence the experiment.
This board has four basic colors:
- Red 625nm 4.8W
- Green 520nm 5.8W
- Blue 465nm 5.8W
- White (Warm) 2700K 6.1W
Motor filter shield for peristaltic pump
Small PCB directly soldered to motor terminals of Peristaltic pump motor. It acts as a low pass filter reducing EMI. However, it can also be soldered directly to the motor chassis, further improving EMC. It simplifies motor connection by allowing the motor to be connected via a connector on the board.
Motor filter shield for air pump
Small PCB directly soldered to motor terminals of air pump motor. It acts as a low pass filter reducing EMI. However, it can also be soldered directly to the motor chassis, further improving EMC. It simplifies motor connection by allowing the motor to be connected via a connector on the board.
[WIP] Pump board
Board for expansion pump module, which is used to control additional peristaltic pumps. To this board up to 4 peristaltic pumps can be connected a controlled. Module can be connected to SMPBR reactor via expansion port. Multiple of those modules can be connected to one bio-reactor and can be chained bia expansion ports. Module also have external power, because when more modules will be connected to expansion port, main adapter can be overloaded. External power input is prioritized over power from extension cable.
Sata Expansion port
Fluorometer LED
Parts
229| Qty | Value | Footprint | References |
|---|---|---|---|
| 35 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1001, C1004, C1101, C1104, C1201, C1204, C1301, C1304, C1402, C1502, C1601, C1602, C1603, C1704, C1706, C1707 +19 |
| 26 | 1k | Resistor_SMD:R_0603_1608Metric | R1001, R1002, R1101, R1102, R1201, R1202, R1301, R1302, R1401, R1402, R1501, R1502, R1606, R1607, R1608, R1609 +10 |
| 14 | 1uF | Capacitor_SMD:C_0603_1608Metric | C202, C208, C209, C216, C218, C302, C602, C702, C801, C803, C1401, C1403, C1501, C1503 |
| 13 | 10R@100MHz | Inductor_SMD:L_0603_1608Metric | FB201, FB301, FB601, FB701, FB801, FB802, FB1401, FB1402, FB1501, FB1502, FB1601, FB1602, FB1701 |
| 12 | 10k | Resistor_SMD:R_0603_1608Metric | R207, R209, R217, R302, R303, R602, R603, R702, R703, R1603, R1604, R1605 |
| 10 | 10uF/25V | Capacitor_SMD:CP_Elec_4x5.4 | C805, C1002, C1102, C1202, C1302, C1405, C1505, C1701, C1702, C1705 |
| 8 | 10nF | Capacitor_SMD:C_0603_1608Metric | C804, C1003, C1103, C1203, C1303, C1404, C1504, C1703 |
| 7 | 270R | Resistor_SMD:R_0603_1608Metric | R203, R208, R210, R211, R212, R1804, R1805 |
| 7 | 5.1k | Resistor_SMD:R_0603_1608Metric | R201, R202, R218, R1601, R1602, R1802, R1803 |
| 7 | B5817W | Diode_SMD:D_SOD-123 | D301, D302, D601, D602, D701, D702, D1801 |
| 6 | 68uH | Inductor_SMD:L_Sumida_CDMC6D28_7.25x6.5mm | L401, L402, L1001, L1101, L1201, L1301 |
| 5 | DF3A-2P-2DS | TCY_connectors:Hirose_DF3A-02P-2DS_1x02_P2.00mm_Horizontal | J401, J402, J403, J1601, J1602 |
| 5 | SS34 | Diode_SMD:D_SMA | D1001, D1101, D1201, D1301, D1702 |
| 4 | 10uF | Capacitor_SMD:C_0805_2012Metric | C401, C402, C403, C404 |
| 4 | AP8802 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm_ThermalVias | U1001, U1101, U1201, U1301 |
| 4 | M2.5 | MountingHole:MountingHole_2.7mm_M2.5_DIN965 | MK101, MK102, MK103, MK104 |
| 4 | RED | LED_SMD:LED_0603_1608Metric | D201, D202, D203, D1802 |
| 3 | 0R | Resistor_SMD:R_0603_1608Metric | R206, R403, R1801 |
| 3 | 10R | Resistor_SMD:R_0603_1608Metric | R301, R601, R701 |
| 3 | 2.2k | Resistor_SMD:R_0603_1608Metric | R305, R605, R705 |
| 3 | 2.54-2*5P | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J901, J902, J1701 |
| 3 | DF3A-3P | TCY_connectors:Hirose_DF3A-03P-2DS_1x03_P2.00mm_Horizontal | J301, J601, J701 |
| 3 | DMC3071 | Package_TO_SOT_SMD:TSOT-23-6 | Q301, Q601, Q701 |
| 3 | DRV8870DDA | Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U801, U1401, U1501 |
| 3 | LOGO | LOGO | G***, G***, G*** |
| 3 | TLH | TCY_mechanical:ToolingHole_JLCPCB | FID101, FID102, FID103 |
| 2 | 0.5/1mm | Fiducial:Fiducial_1mm_Mask2mm | FID104, FID105 |
| 2 | 100mR/0.5W | Resistor_SMD:R_1210_3225Metric | R401, R402 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C206, C207 |
| 2 | 22R | Resistor_SMD:R_0603_1608Metric | R214, R215 |
| 2 | 60R | Resistor_SMD:R_1206_3216Metric | R1701, R1702 |
| 2 | BM03B-SRSS-TB | Connector_JST:JST_SH_BM03B-SRSS-TB_1x03-1MP_P1.00mm_Vertical | J1801, J1804 |
| 2 | Pin_header_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1803, J1805 |
| 2 | TS-1187A-B-A-B | Button_Switch_SMD:SW_SPST_TL3342 | SW201, SW202 |
| 1 | 10k, 3950b | Inductor_SMD:L_0603_1608Metric | TH1601 |
| 1 | 12MHz | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y201 |
| 1 | 74HC14 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U501 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1701 |
| 1 | ARM_SWD_10 | Connector:Tag-Connect_TC2050-IDC-NL_2x05_P1.27mm_Vertical_with_bottom_clip | J1806 |
| 1 | AT24C256 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U201 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D205 |
| 1 | PH-00244 | Connector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_Vertical | J1702 |
| 1 | PSM712-LF-T7 | Package_TO_SOT_SMD:SOT-23 | D1701 |
| 1 | REF3033 | Package_TO_SOT_SMD:SOT-23 | U203 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U204 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1702 |
| 1 | U263-163N-4BLS1735 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1802 |
| 1 | W25Q32JVZP | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U202 |
| 1 | YELLOW | LED_SMD:LED_0603_1608Metric | D204 |
More from TrendBit/SMBR-hardware
12- 4 layers140 × 70 mm

- 4 layers90 × 100 mm

- 2 layers65 × 56 mm

Interface board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
133 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
103 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
91 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
91 partsGPL-3.0 - 2 layers97 × 100 mm

- 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
67 partsGPL-3.0 - 2 layers80 × 100 mm

Illumination board
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
15 partsGPL-3.0 - 2 layers24 × 25.5 mm

Motor shield peristaltic
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
15 partsGPL-3.0 - 2 layers20.1 × 22 mm

Motor shield airpump
TrendBit/SMBR-hardware
Design file for SMBR hardware modules in KiCAD.
14 partsGPL-3.0 - 2 layers20.3 × 22.5 mm

Similar boards
- 8 layers120 × 100 mm

- 4 layers50 × 20 mm

GigaPower200V
kaminaris/GigaESC-Power200V
Compact 50 × 20 mm non-isolated power-supply module for the modular GigaESC platform, intended for the 200 V version. Provides 12 V, 5 V and 3.3 V rails through a separate output connector.
70 parts - 4 layers50 × 50 mm

STMF103C8T6 Dev Board
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
52 parts915 - 4 layers70 × 70 mm

Windsensor
kristofkatzenberger/windsensor
This repository contains the design files for a portable wind sensor developed in 2025/26 at the University of Applied Sciences Technikum Wien. This project was completed as part of the Bachelor's Thesis:
128 partsMIT - 4 layers

SUNNY C1-HEAD
RSXLX/sunny-the-growing-sunflower-lamp
SUNNY — The Growing Sunflower Lamp | A personal lamp with customizable exteriors, traceable fabrication, and a local creative workspace.
55 parts - 4 layers100 × 68 mm

- 2 layers35 × 79 mm

STM32G431C8T6
BypassCapacitor/G431_S_V1
STM32G431C8T6 system board, temporarily designed for the 2024 Electronic Design Competition.
91 parts1 - 6 layers34.4 × 20 mm

GigaControl
kaminaris/GigaESC-ControlBoard
Compact six-layer control card for modular GigaESC motor controllers. The MCU, CAN transceiver, IMU and signal conditioning live here; the MOSFET power stage and power supply are separate boards.
54 parts
Questions
How big is the Control board PCB?
It measures 56 × 85 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Control board use?
229 parts, built around the RP2040, SN65HVD230DR, AP8802SG and DRV8870DDAR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Control board KiCad files?
From the TrendBit/SMBR-hardware repository on GitHub, at the commit this page was made from: the board is control_board/control_board.kicad_pcb and its schematic control_board/MCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Control board design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).