Skip to the content
PCBKitNew board

Microcontroller

177 boards

KiCad boards from 96 GitHub repositories tagged “microcontroller”, the most starred first; open any of them in PCBKit.

  • 2 layers52 × 26 mmDml10, the printed circuit board in 3D

    Dml10

    jonnor/embeddedml

    Notes on Machine Learning on edge for embedded/sensor/IoT uses

    51 parts317
  • 2 layers118.1 × 101.6 mmTeensy eurorack, the printed circuit board in 3D

    Teensy eurorack

    newdigate/teensy-eurorack

    Hardware Design: Eurorack shield for teensy 4.1 with 14 in / 16 out analog channels

    102 parts259MIT
  • 2 layers21.2 × 51.6 mmEnvPicoLiPo, the printed circuit board in 3D

    EnvPicoLiPo

    Envious-Data/EnvOpenPico

    An open source RP2040 MCU Board Family

    57 parts151GPL-3.0
  • 2 layers165 × 78 mmCHIPnGo, the printed circuit board in 3D

    CHIPnGo

    kurtjd/CHIPnGo

    A custom-built CHIP-8 hand-held gaming console powered by a STM32 microcontroller.

    13 parts122MIT
  • 4 layers60 × 95 mmSTM32H7 GuitarPedal, the printed circuit board in 3D

    STM32H7 GuitarPedal

    GuitarML/GuitarPedalSTM32

    Guitar pedal using a stm32h7 microcontroller programmed with CubeIDE (PCB and Firmware)

    101 parts100MIT
  • 2 layers68.6 × 53.3 mmDw probe tht, the printed circuit board in 3D

    Dw probe tht

    felias-fogg/dw-link

    An Arduino-UNO-based debugWIRE hardware-debugger

    28 parts90GPL-3.0
  • 2 layers259.5 × 89.1 mmSteno, the printed circuit board in 3D

    Steno

    crides/steno

    Embedded steno firmware + custom steno PCBs

    61 parts75MIT
  • 2 layers29.8 × 33.7 mmPecanpico9, the printed circuit board in 3D

    Pecanpico9

    DL7AD/pecanpico9

    A lightweight APRS tracker for balloons

    116 parts68GPL-3.0
  • 2 layers14.5 × 12 mmPlayStation-1-Reset Mod, the printed circuit board in 3D

    PlayStation-1-Reset Mod

    pyroesp/PlayStation-1-Reset-Mod

    PlayStation 1 Controller Reset mod

    16 parts61
  • 4 layers95 × 50 mmControl board, the printed circuit board in 3D

    Control board

    ZhuYanzhen1/MM32_CLion

    本项目是全国大学生智能车竞赛GDUT 2022年极速越野组的项目文件。采用了LQR控制器和多速率卡尔曼融合算法,并在单片机上实现。This project is the project document for the GDUT 2022 Extreme Off-Road Category of the National Student Intelligent Vehicle Competition.

    129 parts58AGPL-3.0
  • 2 layers71.1 × 95.3 mmPlaca PIC18F4550, the printed circuit board in 3D

    Placa PIC18F4550

    WelsTheory/PIC18F4550-TUTORIAL

    PIC18F4550 - TUTORIAL

    36 parts55
  • 2 layers40.6 × 27.9 mmCH552, the printed circuit board in 3D

    CH552

    nicola-strappazzon/CH552

    Basic projects with CH552G

    23 parts37LGPL-2.1
  • 2 layers51 × 21 mmMitayi Pico D1, the printed circuit board in 3D

    Mitayi Pico D1

    CIRCUITSTATE/Mitayi-Pico-D1

    Open-Source RP2040 Microcontroller Development Board

    75 parts36MIT
  • 2 layers148.8 × 132.2 mmUsbflashprog, the printed circuit board in 3D

    Usbflashprog

    robsonsmartins/usbflashprog

    A memory device programmer (Flash/EPROM/E2PROM) board and software, connected to PC by USB port.

    125 parts36
  • 2 layers101.6 × 53.3 mmAvr hv2, the printed circuit board in 3D

    Avr hv2

    dilshan/avr-hv2

    AVR High Voltage Programmer 2

    17 parts30MIT
  • 4 layers220 × 120 mmElectricui arena, the printed circuit board in 3D

    Electricui arena

    electricui/electricui-arena

    Hardware for continuous integration testing of serial interfaces and microcontrollers

    268 parts27MIT
  • 2 layers242 × 60 mmRoothubs, the printed circuit board in 3D

    Roothubs

    gkiefer/home2l

    The Home2Ls - Smart Tools for a Private Home

    178 parts21
  • 2 layers25.2 × 36.8 mmUsb kb, the printed circuit board in 3D

    Usb kb

    KrzysztofW/microdevt

    Microcontroller Development Toolkit

    18 parts20GPL-2.0
  • 2 layers66.3 × 53.2 mmEEW5, the printed circuit board in 3D

    EEW5

    mribble/ElectricEelWheel5

    The Electric Eel Wheel 5 is an electric spinning wheel that converts fiber (an example being sheep's wool) into yarn. This site contains the open source files for this project.

    61 parts14
  • 2 layers50.8 × 22.9 mmWing, the printed circuit board in 3D

    Wing

    Bucknalla/kicad-feather-wing-template

    KiCAD 7 template for Adafruit Feather Wings

    2 parts9MIT
  • 2 layers23 × 19 mmOpenRCDG, the printed circuit board in 3D

    OpenRCDG

    dot1nt/openRCDG

    An Arduino based rc drift gyro

    28 parts8GPL-3.0
  • 2 layers149.2 × 83.7 mmNodo BMS 1 1, the printed circuit board in 3D

    Nodo BMS 1 1

    AugustoS97/BMS-BatterySystem

    Repositorio con el diseño de un BMS y una batería como TFM

    117 parts7GPL-3.0
  • 2 layers30.1 × 30 mmDA14531MOD Breakout, the printed circuit board in 3D

    DA14531MOD Breakout

    kattaliraees/DA14531MOD-Breakout

    DA14531MOD-Breakout board

    3 parts6MIT