Skip to the content

Radio and wireless

4,012 boards
  • 2 layers60 × 100 mmEsp gps ntp, the printed circuit board in 3D

    Esp gps ntp

    liebman/esp32-gps-ntp

    This is an esp-idf app using platformio.

    28 parts22MIT
  • 4 layers55.5 × 64.5 mmPico2 12bitadc, the printed circuit board in 3D

    Pico2 12bitadc

    Sev5000/Pico2_12bitADC_PCMAudio

    PCB to neatly package a Raspberry Pi Pico 2 with an AD9226 12bit ADC and PCM1802 for capture with HSDAOH

    36 parts22
  • 2 layers56.6 × 57.7 mmQuack, the printed circuit board in 3D

    Quack

    demik/quack

    Bluetooth and ADB Mouse Converter for Macintosh 128/512/Plus, Apple Lisa and Apple IIc

    52 parts21Apache-2.0
  • 2 layers58 × 26.8 mmQn8035-tuner, the printed circuit board in 3D

    Qn8035-tuner

    dilshan/qn8035-rpi-fm-radio

    QN8035 based Raspberry Pi FM radio receiver

    25 parts21MIT
  • 6 layers50.9 × 30 mmLoRa PCIe GW, the printed circuit board in 3D

    LoRa PCIe GW

    NebraLtd/LoRa-mPCIe

    Open source mPCIe LoRa® concentrators from Nebra

    269 parts21Apache-2.0
  • 2 layers80 × 24 mmRick Flash, the printed circuit board in 3D

    Rick Flash

    rectifiedtech/Rick-Flash

    A 960TB SSD that Rick Rolls you via a piezo buzzer and a WiFi access point.

    22 parts21MIT
  • 2 layers15.8 × 36.8 mmDigirig Lite, the printed circuit board in 3D

    Digirig Lite

    softcomplex/Digirig-Lite

    Minimalistic CM108B-based digital modes interface for ham radio

    54 parts21GPL-3.0
  • 2 layers111.3 × 87.7 mmCorne choc xiao, the printed circuit board in 3D

    Corne choc xiao

    tufourn/corne-choc-xiao

    Corne keyboard with XIAO BLE microcontroller and LIR2032 support

    51 parts21
  • 2 layers97 × 97 mmQO100 RX, the printed circuit board in 3D

    QO100 RX

    barisdinc/N3B_SDR_Transceiver_HW

    V/U/SHF and QO-100 SDR Transceiver Project

    167 parts20GPL-3.0
  • 2 layers42 × 30.8 mmWifiaudiorx, the printed circuit board in 3D

    Wifiaudiorx

    BearLaboratory/wifiaudio-rx-hardware

    基于ESP32的WiFi无线麦克风接收端

    52 parts20GPL-3.0
  • 2 layers29.5 × 24.3 mmEidon tracker, the printed circuit board in 3D

    Eidon tracker

    Eidon-AI/eidon-tracker

    Wearable battery powered IMU to Bluetooth module.

    19 parts20
  • 2 layers62.9 × 47 mmESP32 CAN, the printed circuit board in 3D

    ESP32 CAN

    FL0WL0W/ESP32C3-CAN-Extender

    This module uses an ESP32C3 with WiFi and BLE. It has 3 configurable outputs (5V push pull, Open Drain, 12V pullup), 4 analog or digital inputs, CAN transceiver, and an automotive power supply so it can be installed…

    72 parts20GPL-3.0
  • 2 layers33 × 51.6 mmTpms silencer, the printed circuit board in 3D

    Tpms silencer

    gcormier/tpms_silencer

    Spoof TPMS sensors to prevent blinking lights/etc

    27 parts20
  • 2 layers69.5 × 40.5 mmPendant v2, the printed circuit board in 3D

    Pendant v2

    gjkrediet/Fluid-controller

    A wireless battery powered pendant for FluidNC based on esp32

    10 parts20GPL-3.0
  • 4 layers100 × 100 mmHGS Reflector, the printed circuit board in 3D

    HGS Reflector

    oresat/oresat-live-handheld-ground-station

    MCAD, ECAD, software, firmware, build instructions, and everything else you should need for the OreSat Live Handheld Ground Station project.

    64 parts20GPL-3.0
  • 2 layers47.8 × 50.8 mm2AAAHolder, the printed circuit board in 3D

    2AAAHolder

    pa-pa/HMSensor

    Flexible Hardware Platform for 868MHz Sensors and Actors

    53 parts20
  • 2 layers36 × 31 mmESPDimmer, the printed circuit board in 3D

    ESPDimmer

    stelioskat/esp8266-led-dimmer

    Wifi enabled LED strip dimmer that is controlled using MQTT messages.

    11 parts20MIT
  • 2 layers44.4 × 22 mmNRF52840-FART V3, the printed circuit board in 3D

    NRF52840-FART V3

    tomasmcguinness/zigbee-nrf-flow-and-return-temperature-sensor

    A zigbee based, dual probe temperature sensor designed to operate on battery.

    9 parts20
  • 2 layers51.7 × 29.2 mmAVR LORA-805, the printed circuit board in 3D

    AVR LORA-805

    tomtor/STM32-RFM95-PCB

    STM32 and AVR128 Printed Circuit Board for creating IOT nodes with the RFM95 LORA chip

    39 parts20GPL-3.0
  • 2 layers39.6 × 23.2 mmDetector, the printed circuit board in 3D

    Detector

    Ttl/detector

    RF power detector board design files

    52 parts20
  • 2 layers54.4 × 63.7 mmWiC64 Plugin, the printed circuit board in 3D

    WiC64 Plugin

    WiC64-Team/wic64-hardware

    WiC64 WiFi Adapter schematics and gerber files

    59 parts20CC-BY-4.0
  • 2 layers233.6 × 89.5 mmNostrumX2, the printed circuit board in 3D

    NostrumX2

    bennytrouser/NostrumX

    A 32 key ergonomic split keyboard using Seeed Xiao BLE

    90 parts19MIT
  • 2 layers35.6 × 20.3 mmModel T RAM, the printed circuit board in 3D

    Model T RAM

    bkw777/Model_T_RAM

    8K RAM module for "Model T Computers" - TRS-80 Model 100, Kyotronic KC-85, NEC PC-8201, Olivetti M10

    5 parts19