

ESP32 CAN
This module uses an ESP32C3 with WiFi and BLE. It has 3 configurable outputs (5V push pull, Open Drain, 12V pullup), 4 analog or digital inputs, CAN transceiver, and an automotive power supply so it can be installed…
- Size
- 62.9 × 47 mm
- Copper layers
- 2
- Thickness
- 0.6 mm
- Parts
- 72
- Nets
- 53
- Pads
- 269
- Tracks, vias
- 404, 987
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 11 Oct 2022
- Updated
- 5 Nov 2026
Overview
ESP32 CAN is an open-source printed circuit board by FL0WL0W, from the FL0WL0W/ESP32C3-CAN-Extender repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 62.9 × 47 mm with 72 parts on 53 nets, routed with 404 tracks and 987 vias.
It is built around the ATA6561-GAQW-N, ESP32-C3-MINI-1 and LM2576S-5.0, with the AMS1117-3.3, BD5230G-TR and BSS138BKW among its other parts. Its parts include 26 resistors, 19 capacitors, 11 diodes, 7 transistors and 5 ICs. It belongs with the radio and wireless boards and the ESP32 and RISC-V boards of this library.
Main components
6ATA6561-GAQW-N
SOIC-8-40℃~+150℃ 12uA 4.5V~5.5V 5Mbps 70mA CAN Transceiver SOIC-8 CAN Transceivers ROHSMicrochip TechnologyCAN TransceiversESP32-C3-MINI-1
--40℃~+81℃ -89dBm 2.4GHz 350mA 3V~3.6V 82mA ESP32-C3 Chip On-board PCB Antenna UART - WiFi Modules ROHSRF CrazyWiFi ModulesLM2576S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 3A 4V~40V 52kHz 5V 5mA Buck Built-in Fixed No Step-down type TO-263-5 DC-DC Converters ROHSSlkorDC-DC ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBD5230G-TR
SSOP-5-1.6mm-40℃~+105℃@(Tj) 1 2.3V~6V 3V 950nA Active Low No No Open Drain Voltage Detector SSOP-5-1.6mm Supervisor and Reset ICs ROHSROHM SemiconductorSupervisor And Reset ICsBSS138BKW
SOT-323-55℃~+150℃ 1 N-channel 1.5Ω@10V 1V 2.2pF 236mW 25pF 360mA 60V 650pC@4.5V 9.7pF N-Channel SOT-323 MOSFETs ROHSElecSuperMOSFETs
README
README.mdESP32C3 CAN Extender
This module uses an ESP32C3 with WiFi and BLE.
It has 3 configurable outputs (5V push pull, Open Drain, 12V pullup), 4 analog or digital inputs, CAN transceiver,
and an automotive power supply so it can be installed directly into a vehicle. It can be programmed and debugged using the edge connector that connects to any standard
USBC cable. If you decide to order a PCB yourself, make sure to order it as 0.6mm thickness so that the PCB will fit in the USBC connector.
The purpose of this module will be to add cruise control, AC control, tachometer output, speedometer output, and fuel consumption output to my LS3 swapped BMW E30.
The LS3 is currently controlled by the stock GM E38 PCM. This PCM (Powertrain Control Module) uses the CAN bus for the aforementioned items, and this is meant to be a bridge from CAN, to
discrete signals. This job is originally handled by the BCM (Body Control Module), However the BCM includes alot of items that are not needed for a typical swap, and there
is not very good documentation on the various BCMs available in cars (compatibility, pinout, etc.). In the future, this car will run on an
EFIGenie PCM once the software is more mature. This module will then be useful as a CAN extension module.
A demo program will be added soon that has all of the aforementioned features hardcoded, but the eventual goal is to utilize the work from my other repositories
to create a configurable module that can be programmed through a web UI for various tasks. Another potential feature would be to implement an emulation of the ubiquitous ELM327 bluetooth module that can be used to connect to a phone or tablet to read diagnostic codes, read sensors, or create a digital dash.
A 3d model of the enclosure will be uploaded soon as well. The plan is to epoxy pot the pcb inside the enclosure to make it waterproof.

Parts
72| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 10n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C4, C5, C7, C8, C10, C16, C17, C18, C19 |
| 11 | DNI | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R5, R8, R14, R15, R16, R17, R23, R24, R25, R26 |
| 9 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R6, R7, R9, R18, R19, R20, R21, R22 |
| 4 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10, R11, R12, R13 |
| 4 | 3.3V | Diode_SMD:D_SOD-123 | D7, D8, D9, D10 |
| 4 | 51V | Diode_SMD:D_SOD-123 | D3, D4, D5, D6 |
| 4 | BSS138BKW | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q2, Q4, Q5, Q7 |
| 3 | DNI | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q1, Q3, Q6 |
| 3 | D_Schottky | Diode_SMD:D_SOD-123 | D1, D2, D11 |
| 2 | 0.1μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11, C15 |
| 2 | 100μ | Capacitor_SMD:CP_Elec_10x10.5 | C1, C13 |
| 2 | 1μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12, C14 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 1000μ | Capacitor_SMD:CP_Elec_10x10.5 | C6 |
| 1 | 100μ | Inductor_SMD:L_12x12mm_H4.5mm | L1 |
| 1 | 10μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | ATA6561-GAQW-N | Microchip:ATA6561-GAQW-N | U1 |
| 1 | BD5230G-TR | TI:TPS3840DL18DBVR | U4 |
| 1 | Conn_01x18_Male | MX23A:MX23A18NF1 | J1 |
| 1 | ESP32-C3-MINI-1 | Espressif:ESP32-C3-MINI-1 | U5 |
| 1 | LM2576S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U2 |
| 1 | USB_C_Receptacle_USB2.0 | usbc2:USB_TYPE_C_DS_6 | J2 |
| 1 | Varistor | Varistor:RV_Disc_D15.5mm_W3.9mm_P7.5mm | RV1 |
Similar boards
- 2 layers40 × 80 mm

- 4 layers97 × 97.4 mm

QEdge UI
qinno/qEdge-UI
qedge+ is the industry's low power design alternative to the standard PC approach. qEdge-UI is part of qEdge+ and consists of a RaspBerry Pico with LCD, touch screen and keys and an 868MHz LoRa radio module.
170 parts3 - 2 layers91.5 × 53.2 mm

- 2 layers50 × 32.8 mm

- 2 layers57.2 × 57.2 mm

- 4 layers92 × 60 mm

- 2 layers84.5 × 54.6 mm

Main board v2
felixzero/escrocs
Repository for the ESCROCS team for the french robotics cup 2020!
75 parts7GPL-3.0 - 2 layers100 × 100 mm

Questions
How big is the ESP32 CAN PCB?
It measures 62.9 × 47 mm and has 2 copper layers, 0.6 mm thick.
What parts does the ESP32 CAN use?
72 parts, built around the ATA6561-GAQW-N, ESP32-C3-MINI-1, LM2576S-5.0 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32 CAN KiCad files?
From the FL0WL0W/ESP32C3-CAN-Extender repository on GitHub, at the commit this page was made from: the board is KiCAD Project/ESP32_CAN.kicad_pcb and its schematic KiCAD Project/ESP32_CAN.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32 CAN design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).