Skip to the content
123456

TPS2552DBV

Texas InstrumentsExtended

-40℃~+150℃ 1 1.5A 2.5V~6.5V 85mΩ Active Low High Side Switch Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-23-6 Power Distribution Switches ROHS

Part id
ti/TPS2552DBV
Category
Power Distribution Switches
Package
SOT-23-6
Pins
6
In stock
10,219 at JLCPCB (C46506)
Used on
3 open-source boards

Overview

The TPS2552DBV is a power Distribution Switche made by Texas Instruments in a SOT-23-6 package with 6 pins. -40℃~+150℃ 1 1.5A 2.5V~6.5V 85mΩ Active Low High Side Switch Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-23-6 Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS2552DBVR-1, from EasyEDA) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 10,219 are in stock at JLCPCB (part C46506). 3 open-source boards in 2 repositories on GitHub use it.

Symbol

1IN2GND3EN4FAULT5ILIM6OUT
EasyEDA_Cloud:TPS2552DBVR-1From EasyEDA

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

18
Supply, least
2.5 V · IN, recommended operating minimum · p. 6
Supply, most
6.5 V · IN, recommended operating maximum · p. 6
Supply, absolute maximum
7 V · IN, absolute maximum · p. 5
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 5
Takes working
120 µA · IN, output enabled, no load, VIN = 6.5 V, RILIM = 20 kΩ, typical · p. 7
Takes asleep
100 nA · IN, output disabled, VIN = 6.5 V, no load, typical · p. 7
Gives
1.2 A · OUT, continuous maximum at −40 °C ≤ TJ ≤ 125 °C · p. 6
Gives
1.5 A · OUT, continuous maximum at −40 °C ≤ TJ ≤ 105 °C · p. 6
Current limit
1.7 A · RILIM = 15 kΩ, −40 °C ≤ TJ ≤ 105 °C, typical · p. 7
Current limit
1.295 A · RILIM = 20 kΩ, TJ = 25 °C, typical · p. 7
Current limit
520 mA · RILIM = 49.9 kΩ, TJ = 25 °C, typical · p. 7
Current limit
130 mA · RILIM = 210 kΩ, typical · p. 7
Current limit
75 mA · ILIM shorted to IN, typical · p. 7
A pin gives at most
25 mA · FAULT continuous sink current, absolute maximum · p. 5
Junction to air (DBV (SOT-23))
182.6 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to board (DBV (SOT-23))
29.4 K/W · Junction-to-board thermal resistance · p. 6
Junction to case (DBV (SOT-23))
122.2 K/W · Junction-to-case top thermal resistance · p. 6
Edge
700 µs · OUT rise time, VIN = 2.5 V, CL = 1 uF, RL = 100 Ω, typical · p. 7

What it is and has

6
Protection
Reverse input-output voltage protection · p. 1
Soft start
Built-in · p. 1
Overcurrent behavior
Constant-current mode · p. 13
Enable polarity
Active low · p. 5
Current-limit accuracy
±6% at 1.7 A (typical) · p. 1
USB current limiting
Meets USB current-limiting requirements · p. 1

Around it

6
cap 0.1 µF or greater
between IN and GND; Ceramic; place as close to the IC as possible. · p. 5
res 15 kΩ to 232 kΩ
between ILIM and GND; Nominal 1% resistor sets the current-limit threshold. · p. 6
cap 0.1 µF or greater
between IN and GND; Ceramic bypass capacitor; place as close to the device as possible for local noise decoupling. · p. 20
cap high-value
between OUT and GND; Electrolytic capacitor recommended when large transient output currents are expected. · p. 20
res 15 kΩ ≤ RILIM ≤ 232 kΩ
between ILIM and GND; Use a 1% resistor to program the current-limit threshold; keep routing as short as possible. · p. 15
res 23.7 kΩ
between ILIM and GND; Application example: 1% resistor selected for a minimum current-limit threshold of 1 A. · p. 18

Specifications

59
ParameterConditionsAs printedPage
Voltage range on IN, OUT, EN or EN, ILIM, FAULTVoltages referenced to GNDmin -0.3 · max 7 V5
Voltage range from IN to OUTmin -7 · max 7 V5
Continuous FAULT sink currentmin 0 · max 25 mA5
ILIM source currentmin 0 · max 1 mA5
Maximum junction temperature TJmin -40 · max 150 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; value ±2000 Vmax 2000 V6
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; value ±500 Vmax 500 V6
Electrostatic discharge V(ESD)IEC 61000-4-2 contact discharge; value ±8000 Vmax 8000 V6
Electrostatic discharge V(ESD)IEC 61000-4-2 air-gap discharge; value ±15000 Vmax 15000 V6
Input voltage, IN VINmin 2.5 · max 6.5 V6
Enable voltage VENTPS2552/52-1min 0 · max 6.5 V6
High-level input voltage on EN or EN VIHmin 1.1 V6
Low-level input voltage on EN or EN VILmax 0.66 V6
Continuous output current, OUT IOUT–40 °C ≤ TJ ≤ 125 °Cmin 0 · max 1.2 A6
Continuous output current, OUT IOUT–40 °C ≤ TJ ≤ 105 °Cmin 0 · max 1.5 A6
Current-limit threshold resistor range (nominal 1%) from ILIM to GND RILIMmin 15 · max 232 kΩ6
Continuous FAULT sink current IOmin 0 · max 10 mA6
Input de-coupling capacitance, IN to GNDmin 0.1 uF6
Operating virtual junction temperature TJIOUT ≤ 1.2 Amin -40 · max 125 °C6
Operating virtual junction temperature TJIOUT ≤ 1.5 Amin -40 · max 105 °C6
Junction-to-ambient thermal resistance RθJATPS2552, DBV (SOT-23), 6 PINStyp 182.6 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)TPS2552, DBV (SOT-23), 6 PINStyp 122.2 °C/W6
Junction-to-board thermal resistance RθJBTPS2552, DBV (SOT-23), 6 PINStyp 29.4 °C/W6
Junction-to-top characterization parameter ψJTTPS2552, DBV (SOT-23), 6 PINStyp 20.8 °C/W6
Junction-to-board characterization parameter ψJBTPS2552, DBV (SOT-23), 6 PINStyp 28.9 °C/W6
Static drain-source on-state resistance rDS(on)DBV package, TJ = 25°Ctyp 85 · max 95 mΩ7
Static drain-source on-state resistance rDS(on)DBV package, –40°C ≤TJ ≤125°Cmax 135 mΩ7
Rise time, output trCL = 1 uF, RL = 100 Ω, VIN = 6.5 V; see Figure 20typ 1.1 · max 1.5 ms7
Rise time, output trCL = 1 uF, RL = 100 Ω, VIN = 2.5 V; see Figure 20typ 0.7 · max 1 ms7
Fall time, output tfCL = 1 uF, RL = 100 Ω, VIN = 6.5 V; see Figure 20min 0.2 · max 0.5 ms7
Fall time, output tfCL = 1 uF, RL = 100 Ω, VIN = 2.5 V; see Figure 20min 0.2 · max 0.5 ms7
Enable pin turn on/off thresholdmin 0.66 · max 1.1 V7
Input current IENVEN = 0 V or 6.5 V, VEN = 0 V or 6.5 Vmin -0.5 · max 0.5 uA7
Turnon time tonCL = 1 uF, RL = 100 Ω, (see Figure 20)max 3 ms7
Turnoff time toffCL = 1 uF, RL = 100 Ω, (see Figure 20)max 3 ms7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 15 kΩ, –40°C ≤TJ ≤105°Cmin 1610 · typ 1700 · max 1800 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 20 kΩ, TJ = 25°Cmin 1215 · typ 1295 · max 1375 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 20 kΩ, –40°C ≤TJ ≤125°Cmin 1200 · typ 1295 · max 1375 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 49.9 kΩ, TJ = 25°Cmin 490 · typ 520 · max 550 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 49.9 kΩ, –40°C ≤TJ ≤125°Cmin 475 · typ 520 · max 565 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 210 kΩmin 110 · typ 130 · max 150 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSILIM shorted to INmin 50 · typ 75 · max 100 mA7
Response time to short circuit tIOSVIN = 5 V (see Figure 21)typ 2 us7
Reverse-voltage comparator trip point (VOUT – VIN)min 95 · typ 135 · max 190 mV7
Time from reverse-voltage condition to MOSFET turn offVIN = 5 Vmin 3 · typ 5 · max 7 ms7
Supply current, low-level output IIN_offVIN = 6.5 V, No load on OUT, VEN = 6.5 V or VEN = 0 Vtyp 0.1 · max 1 uA7
Supply current, high-level output IIN_onVIN = 6.5 V, No load on OUT, RILIM = 20 kΩtyp 120 · max 140 uA7
Supply current, high-level output IIN_onVIN = 6.5 V, No load on OUT, RILIM = 210 kΩtyp 100 · max 120 uA7
Reverse leakage current IREVVOUT = 6.5 V, VIN = 0 V, TJ = 25 °Ctyp 0.01 · max 1 uA7
Low-level input voltage, IN UVLOVIN risingtyp 2.35 · max 2.45 V7
Hysteresis, INTJ = 25 °Ctyp 25 mV7
Output low voltage, FAULT VOLI/FAULT = 1 mAmax 180 mV7
Off-state leakageV/FAULT = 6.5 Vmax 1 uA7
FAULT deglitchFAULT assertion or de-assertion due to overcurrent conditionmin 5 · typ 7.5 · max 10 ms7
FAULT deglitchFAULT assertion or de-assertion due to reverse-voltage conditionmin 2 · typ 4 · max 6 ms7
Thermal shutdown thresholdmin 155 °C7
Thermal shutdown threshold in current-limitmin 135 °C7
HysteresisThermal shutdowntyp 10 °C7

Pins, by the datasheet

6
1 IN
Input voltage; connect a 0.1 uF or greater ceramic capacitor from IN to GND as close to the IC as possible. · p. 5
2 GND
Ground connection; connect externally to PowerPAD. · p. 5
3 EN
Enable input; logic low turns on power switch. · p. 5
4 FAULT
Active-low open-drain output asserted during overcurrent, overtemperature, or reverse-voltage conditions. · p. 5
5 ILIM
External resistor sets the current-limit threshold; recommended 15 kΩ ≤ RILIM ≤ 232 kΩ. · p. 5
6 OUT
Power-switch output. · p. 5

Ordering codes, by the datasheet

2
TPS2552DBVR
SOT-23 (DBV), 6 pins · Package quantity 3000; operating temperature -40 to 125 °C. · p. 27
TPS2552DBVT
SOT-23 (DBV), 6 pins · Package quantity 250; operating temperature -40 to 125 °C. · p. 27

Open-source boards using it

3
  • 6 layers201.5 × 139.2 mmGc3 panelized, the printed circuit board in 3D

    Gc3 panelized

    masahirosuzuka/GC3

    1,528 parts
  • 6 layers99.1 × 66.8 mmGc3, the printed circuit board in 3D

    Gc3

    masahirosuzuka/GC3

    382 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS2552DBV?

Yes. The symbol is EasyEDA_Cloud:TPS2552DBVR-1 and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS2552DBV?

SOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the TPS2552DBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS2552DBV?

JLCPCB lists it as part C46506, with 10,219 in stock; the sellers' links on this page open their listings.

What can replace the TPS2552DBV?

Parts like it in the library: the TPS22918DBV by Texas Instruments, the TPS2553DBV by Texas Instruments, the AP2553W6 by Diodes Incorporated and the TPS27081ADDC by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS2552DBV?

3 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.