Skip to the content
123456

AP2553W6

Diodes IncorporatedExtended

-40℃~+125℃ 1 2.1A 2.7V~5.5V 70mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Over Voltage Protection、Undervoltage Protection(UVP)、Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-26 Power Distribution Switches ROHS

Part id
diodes/AP2553W6
Category
Power Distribution Switches
Package
SOT-26
Pins
6
In stock
60,339 at JLCPCB (C212302)
Used on
5 open-source boards

Overview

The AP2553W6 is a power Distribution Switche made by Diodes Incorporated in a SOT-26 package with 6 pins. -40℃~+125℃ 1 2.1A 2.7V~5.5V 70mΩ Active High High Side Switch Short-Circuit Protection(SCP)、Over Voltage Protection、Undervoltage Protection(UVP)、Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-26 Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS2552DBVR-1, from EasyEDA) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 60,339 are in stock at JLCPCB (part C212302). 5 open-source boards in 5 repositories on GitHub use it.

Symbol

1IN2GND3EN4FAULT5ILIM6OUT
EasyEDA_Cloud:TPS2552DBVR-1From EasyEDA

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

20
Supply, least
2.7 V · IN, recommended operating minimum · p. 4
Supply, most
5.5 V · IN, recommended operating maximum · p. 4
Supply, absolute maximum
6.5 V · IN, absolute maximum · p. 4
Works from
-40 °C · Operating ambient minimum · p. 4
Works up to
85 °C · Operating ambient maximum · p. 4
Junction, hottest
150 °C · Junction temperature absolute maximum · p. 4
Takes working
100 µA · IN quiescent typical, enabled, VIN = 5.5V, RLIM = 20kΩ · p. 5
Takes working
80 µA · IN quiescent typical, enabled, VIN = 5.5V, RLIM = 210kΩ · p. 5
Takes asleep
100 nA · IN shutdown typical, VIN = 5.5V, disabled · p. 5
Gives
2.1 A · Continuous output maximum, -40°C ≤ TA ≤ +85°C · p. 4
Current limit
2.365 A · Typical, RLIM = 10kΩ, -40°C ≤ TA ≤ +85°C · p. 5
Current limit
1.632 A · Typical, RLIM = 15kΩ, -40°C ≤ TA ≤ +85°C · p. 5
Current limit
1.251 A · Typical, RLIM = 20kΩ, TJ = +25°C · p. 5
Current limit
530 mA · Typical, RLIM = 49.9kΩ, TJ = +25°C · p. 5
Current limit
529 mA · Typical, RLIM = 49.9kΩ, -40°C ≤ TA ≤ +85°C · p. 5
Current limit
142 mA · Typical, RLIM = 210kΩ · p. 5
Current limit
75 mA · Typical, ILIM shorted to IN or GND · p. 5
A pin gives at most
25 mA · FAULT continuous sink absolute maximum · p. 4
Junction to air (W6)
160 K/W · Junction to ambient, High-K board · p. 4
Junction to case (W6)
55 K/W · Junction to case, High-K board · p. 4

What it is and has

11
Maximum load current
2.1A · p. 1
Adjustable current limit
75mA - 2360mA · p. 1
Current-limit accuracy
±6%, 1.63A with RLIM = 15kΩ · p. 1
Over-current behavior
Constant-current · p. 1
Short-circuit response time
2µs typical · p. 1
Soft-start
3ms typical rise time · p. 1
Protection
Over-current, output over-voltage and thermal protection · p. 1
Fault reporting
FAULT output with blanking time · p. 1
ESD protection
2kV HBM, 500V CDM · p. 1
Enable polarity
Active high · p. 1
UL recognition
File Number E322375, Vol. 1 · p. 1

Around it

7
cap 0.1µF or greater
between IN and GND; Ceramic; place as close to the IC as possible. · p. 2
res 10kΩ ≤RLIM≤210kΩ
between ILIM and GND; Recommended 1% current-limit programming resistor; keep traces short. · p. 10
cap 0.01-μF to 0.1-μF
between IN and GND; X7R or X5R ceramic bypass capacitor, close to the device. · p. 11
cap 10μF minimum
between IN and GND; High-value electrolytic capacitor recommended when output load is heavy. · p. 11
cap 120µF
between OUT and GND; High-value electrolytic capacitor recommended when output load is heavy; 120uF output capacitance is required for USB. · p. 11
cap 0.1μF to 4.7μF
between OUT and GND; Ceramic bypass capacitor improves immunity to short-circuit transients and prevents negative output during turn-off. · p. 11
cap 2.2uF 50V 0805
between OUT and GND; External output capacitor used on the EVM for the 15kV system ESD pass test. · p. 4

Specifications

64
ParameterConditionsAs printedPage
Human Body Model ESD Protection HBMTA = +25°Cmax 2 kV4
Charged Device Model ESD Protection CDMTA = +25°Cmax 500 V4
Surges per EN61000-4-2. 1999 Applied to Output Terminals of EVM Note (5) IEC system levelExternal output capacitor; pass test only, not a limitmax 15 kV4
Voltage on IN, OUT, FAULT , ILIM, EN, EN VIN, VOUT, VFAULT, VILIM, VENTA = +25°Cmin -0.3 · max 6.5 V4
Continuous FAULT Sink CurrentTA = +25°Cmax 25 mA4
ILIM Source CurrentTA = +25°Cmax 1 mA4
Maximum Junction Temperature TJ(MAX)min -40 · max 150 °C4
Storage Temperature Range (Note 4) TSTmin -65 · max 150 °C4
Thermal Resistance θJA θJAW6; High-K (Note 6)typ 160 °C/W4
Thermal Resistance θJC θJCW6; High-K (Note 6)typ 55 °C/W4
Power RatingW6; High-K (Note 6); TA ≤ +25°Cmax 625 mW4
Derating Factor Above TA = +25°CW6; High-K (Note 6)typ 6.25 mW/°C4
Power RatingW6; High-K (Note 6); TA = +70°Cmax 340 mW4
Power RatingW6; High-K (Note 6); TA = +85°Cmax 250 mW4
Input Voltage VINTA = +25°Cmin 2.7 · max 5.5 V4
Continuous Output Current (-40°C ≤ TA ≤ +85°C) IOUT-40°C ≤ TA ≤ +85°Cmin 0 · max 2.1 A4
Enable Voltage VENmin 0 · max 5.5 V4
High-Level Input Voltage on EN or EN VIHMaximum: VINmin 2 V4
Low-Level Input Voltage on EN or EN VILmin 0 · max 0.8 V4
Current-Limit Threshold Resistor Range RLIM1% initial tolerancemin 10 · max 210 kΩ4
Continuous FAULT Sink Current IOmin 0 · max 10 mA4
Input De-Coupling Capacitance, IN to GNDmin 0.1 uF4
Operating Ambient Temperature TAmin -40 · max 85 C4
Operating Junction Temperature TJmin -40 · max 125 C4
Input UVLO VUVLOVIN Risingtyp 2.4 · max 2.65 V5
Input UVLO Hysteresis VUVLOVIN Decreasingtyp 25 mV5
Input Shutdown Current ISHDNVIN = 5.5V, Disabled, OUT = Opentyp 0.1 · max 1 uA5
Input Quiescent Current IQVIN = 5.5V, Enabled, OUT = Open, RLIM = 20kΩtyp 100 · max 140 uA5
Input Quiescent Current IQVIN = 5.5V, Enabled, OUT = Open, RLIM = 210kΩtyp 80 · max 120 uA5
Reverse Leakage Current IREVDisabled, VIN = 0V, VOUT = 5.5V, IREV at VINtyp 0.01 · max 1 uA5
Switch On-Resistance RDS(ON)SOT26 Package, TJ = +25°C, VIN = 5.0Vtyp 70 · max 95 mΩ5
Switch On-Resistance RDS(ON)SOT26 Package, -40°C ≤ TA ≤ +85°Cmax 135 mΩ5
Output Turn-On Rise Time tRVIN = 5.5V, CL = 1uF, RLOAD = 100Ω. See Figure 1typ 1.1 · max 1.5 ms5
Output Turn-On Rise Time tRVIN = 2.7V, CL = 1uF, RLOAD = 100Ω.typ 0.7 · max 1 ms5
Output Turn-Off Fall Time tFVIN = 5.5V, CL = 1uF, RLOAD = 100Ω. See Figure 1min 0.1 · max 0.5 ms5
Output Turn-Off Fall Time tFVIN = 2.7V, CL = 1uF, RLOAD = 100Ω.min 0.1 · max 0.5 ms5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 10kΩ, -40°C ≤ TA ≤ +85°Cmin 2200 · typ 2365 · max 2542 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 15kΩ, -40°C ≤ TA ≤ +85°Cmin 1540 · typ 1632 · max 1730 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 20kΩ, TJ = +25°Cmin 1180 · typ 1251 · max 1326 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 20kΩ, -40°C ≤ TA ≤ +85°Cmin 1160 · typ 1251 · max 1340 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 49.9kΩ, TJ = +25°Cmin 500 · typ 530 · max 562 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 49.9kΩ, -40°C ≤ TA ≤ +85°Cmin 485 · typ 529 · max 573 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITRLIM = 210kΩmin 121 · typ 142 · max 162 mA5
Current-Limit Threshold (maximum DC output current), VOUT = VIN -0.5V ILIMITILIM Shorted to IN or GNDmin 50 · typ 75 · max 100 mA5
Short-Circuit Current Limit, OUT Connected to GND ISHORTRLIM = 10kΩtyp 2620 mA5
Short-Circuit Current Limit, OUT Connected to GND ISHORTRLIM = 15kΩtyp 1820 mA5
Short-Circuit Current Limit, OUT Connected to GND ISHORTRLIM = 20kΩtyp 1380 mA5
Short-Circuit Current Limit, OUT Connected to GND ISHORTRLIM = 49.9kΩtyp 570 mA5
Short-Circuit Current Limit, OUT Connected to GND ISHORTRLIM = 210kΩtyp 150 mA5
Short-Circuit Current Limit, OUT Connected to GND ISHORTILIM Shorted to IN or GNDtyp 75 mA5
Short-Circuit Response Time tSHORTVOUT = 0V to IOUT = ILIMIT (OUT shorted to ground); See Figure 2typ 2 us5
EN Input Leakage Current ILEAK-ENVIN = 5V, VEN = 0V and 6Vmin -0.5 · max 0.5 uA5
Turn-On Time tONCL = 1uF, RL = 100Ω. See Figure 1max 3 ms5
Turn-Off Time tOFFCL = 1uF, RL = 100Ω. See Figure 1max 1 ms5
Discharge Resistance (Note 8) RDISVIN = 5V, Disabled, IOUT =1mAtyp 600 Ω5
Reverse-Voltage Comparator Trip Point VRVPVOUT – VINmin 95 · typ 135 · max 190 mV6
Reverse Current Limit IROCPVOUT – VIN = 200mVtyp 0.72 A6
FAULT Output Low Voltage VOLIFAULT = 1mAmax 180 mV6
FAULT Off Current IFOHVFAULT = 6Vmax 1 uA6
FAULT Blanking and Latch Off Time (Over-Current) tBlank_OCAssertion or deassertion due to overcurrentmin 5 · typ 7.5 · max 10 ms6
FAULT Blanking Time (Reverse-Voltage) tBlank_RVAssertion or deassertion due to reverse-voltagemin 2 · typ 3.75 · max 6 ms6
Thermal Shutdown Threshold TSHDNEnabled, RLOAD = 1kΩtyp 160 °C6
Thermal Shutdown Threshold under Current Limit TSHDN_OCPEnabled, RLOAD = 1kΩtyp 140 °C6
Thermal Shutdown Hysteresis THYStyp 20 °C6

Pins, by the datasheet

6
1 IN
Input supply; connect a 0.1uF or greater ceramic capacitor to GND as close to the IC as possible. · p. 2
2 GND
Ground. · p. 2
3 EN
Enable input; logic high turns on power switch. · p. 2
4 FAULT
Active-low output asserted during over-current, over-temperature, or reverse-voltage conditions. · p. 2
5 ILIM
Use an external resistor to set the current-limit threshold. · p. 2
6 OUT
Output. · p. 2

Ordering codes, by the datasheet

2
AP2553W6-7
SOT26 · Active-high enable; output current limits; 3000 per 7-inch tape and reel; -7 suffix. · p. 12
AP2553W6-7R
SOT26 · Active-high enable; output current limits; 3000 per 7-inch tape and reel; -7R suffix. · p. 12

Open-source boards using it

5
  • 2 layers119.4 × 74.9 mmTtydriver01, the printed circuit board in 3D

    Ttydriver01

    John-Nagle/ttyloopdriver

    Hardware device for driving antique Teletype machines

    73 parts52GPL-3.0
  • 2 layers174 × 111 mmPedalboard hw, the printed circuit board in 3D

    Pedalboard hw

    pedalboard/pedalboard-hw

    pedalboard audio midi processor open hardware

    169 parts14CERN-OHL-P-2.0
  • 4 layers76 × 121 mmBeta main, the printed circuit board in 3D

    Beta main

    BETA-KNH/beta

    Humanoid robot repository.

    93 parts5
  • 4 layers80 × 80 mmTravel router, the printed circuit board in 3D

    Travel router

    0x62b/travel-router

    CM5 travel router carrier board with dual 1G ethernet, wifi

    56 parts1
  • 2 layers130 × 65 mmCan breakout pcb, the printed circuit board in 3D

    Can breakout pcb

    the-mr-music/OrangeCanBreakout

    Board to test the MCP2517 SPI CAN controller together with the Orange Pi Zero Plus 2

    154 parts1CC-BY-SA-4.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AP2553W6?

Yes. The symbol is EasyEDA_Cloud:TPS2552DBVR-1 and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AP2553W6?

SOT-26, with 6 pins. Its footprint is drawn on this page.

Where is the AP2553W6 datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the AP2553W6?

JLCPCB lists it as part C212302, with 60,339 in stock; the sellers' links on this page open their listings.

What can replace the AP2553W6?

Parts like it in the library: the TPS22918DBV by Texas Instruments, the TPS2553DBV by Texas Instruments, the TPS27081ADDC by Texas Instruments and the AP22653W6 by Diodes Incorporated. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AP2553W6?

5 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.