Skip to the content
123456

AP22615AWU

Diodes IncorporatedExtended

-40℃~+85℃ 1 3A 3V~5.5V 40mΩ Active High、Active Low High Side Switch Overvoltage protection、Output discharge function、Soft-start、Under-voltage lockout、Overcurrent Protection、Over temperature protection、Short-Circuit Protection、Reverse current blocking TSOT-23-6 Power Distribution Switches ROHS

Part id
diodes/AP22615AWU
Category
Power Distribution Switches
Package
TSOT-23-6
Pins
6
In stock
715 at JLCPCB (C2680357)
Used on
1 open-source board

Overview

The AP22615AWU is a power Distribution Switche made by Diodes Incorporated in a TSOT-23-6 package with 6 pins. -40℃~+85℃ 1 3A 3V~5.5V 40mΩ Active High、Active Low High Side Switch Overvoltage protection、Output discharge function、Soft-start、Under-voltage lockout、Overcurrent Protection、Over temperature protection、Short-Circuit Protection、Reverse current blocking TSOT-23-6 Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:AP22615AWU, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 715 are in stock at JLCPCB (part C2680357). 1 open-source board in 1 repository on GitHub use it.

Symbol

1OUT2GND3FLG4EN5ISET6IN
Regulator_Linear:AP22615AWUFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

15
Supply, least
3 V · VIN, recommended operating min · p. 4
Supply, most
5.5 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
6 V · VIN, absolute maximum · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 4
Works up to
85 °C · Operating ambient temperature max · p. 4
Junction, hottest
150 °C · Junction temperature max · p. 4
Takes working
300 µA · VIN quiescent current typical, enabled, OUT open · p. 5
Takes asleep
100 nA · VIN shutdown current typical, disabled, OUT open · p. 5
Gives
3 A · Continuous output max, 4.0V ≤ VIN ≤ 5.5V · p. 4
Gives
1.5 A · Continuous output max, 3.0V ≤ VIN < 4.0V · p. 4
Current limit
3.6 A · Overload limit typical, VIN = 5V, VOUT = 4V, RLIM = 1.94kΩ · p. 5
Current limit
1 A · Overload limit typical, VIN = 5V, VOUT = 4V, RLIM = 6.8kΩ · p. 5
Junction to air (TSOT26)
80 K/W · Junction to ambient, TA = +25°C, four-layer JEDEC 51-7 board · p. 4
Junction to case (TSOT26)
30 K/W · Junction to case, TA = +25°C, four-layer JEDEC 51-7 board · p. 4
Edge
200 µs · Output turn-off fall time typical, CL = 10uF, RLOAD = 10Ω, VIN = 5V · p. 5

What it is and has

12
Adjustable current limit
0.4A to 4.0A · p. 1
Enable
Active-low or active-high · p. 1
Output overvoltage protection
Auto recovery · p. 1
Overcurrent protection
Auto recovery · p. 1
Short-circuit protection
Auto recovery · p. 1
Overtemperature protection
Auto recovery · p. 1
Protection
Output reverse voltage/current protection · p. 1
Fast role-swap
Integrated · p. 1
UL recognition
File Number E322375 · p. 1
Certification
IEC60950-1 CB Scheme · p. 1
Certification
IEC62368-1 CB Scheme · p. 1
Package
TSOT26, RoHS compliant · p. 1

Around it

4
cap 1μF
between IN and GND; Required X7R or X5R ceramic bypass capacitor, close to the device. · p. 12
cap 10μF or 47μF
between IN and GND; Recommended close to the input pin when the output transient load is heavy. · p. 12
cap 100μF minimum or 22μF MLCC
between OUT and GND; Required for hot-plug applications; 100uF option is low ESR electrolytic or tantalum. · p. 12
cap 0.1μF
between OUT and GND; Required ceramic bypass capacitor for hot-plug applications; improves short-circuit transient immunity. · p. 12

Specifications

48
ParameterConditionsAs printedPage
Human Body ESD Protection ESD HBMTA = +25°Cmax 2000 V4
Machine Model ESD Protection ESD MMTA = +25°Cmax 200 V4
Input Voltage VINTA = +25°Cmin -0.3 · max 6 V4
Output Voltage (VOUT to GND, VOUT to VIN) VOUTTA = +25°Cmin -0.3 · max 28 V4
Enable Voltage VENTA = +25°C; maximum VIN +0.3 Vmin -0.3 V4
ISET Voltage VISETTA = +25°C; maximum VIN +0.3 Vmin -0.3 V4
Maximum Junction Temperature TJ(max)max 150 °C4
Storage Temperature TSTGmin -65 · max 150 °C4
Thermal Resistance, Junction to Ambient (Note 6) RΘJATSOT26; TA = +25°C; high effective thermal conductivity four-layer test board per JEDEC 51-7max 80 °C/W4
Thermal Resistance, Junction to Case (Note 6) RΘJCTSOT26; TA = +25°C; high effective thermal conductivity four-layer test board per JEDEC 51-7max 30 °C/W4
Input Voltage VINmin 3 · max 5.5 V4
Output Current, 4.0V ≤ VIN ≤ 5.5V IOUT4.0V ≤ VIN ≤ 5.5Vmin 0 · max 3 A4
Output Current, 3.0V ≤ VIN < 4.0V IOUT3.0V ≤ VIN < 4.0Vmin 0 · max 1.5 A4
EN Input Logic Low Voltage VILmin 0 · max 0.4 V4
Current-Limit Threshold Resistor Range (1% Initial Tolerance) RLIM1% Initial Tolerancemin 1.94 · max 6.8 kΩ4
Output Voltage VOUTmin 0 · max 23 V4
EN Input Logic High Voltage VIHMaximum VINmin 1.2 V4
Operating Ambient Temperature TAmin -40 · max 85 C4
Input UVLO VUVLOVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nF; VIN Risingmin 2.1 · typ 2.5 · max 2.9 V5
Input UVLO Hysteresis ΔVUVLOTA = +25°C, CIN = 1uF, CL = 100nF; VIN Decreasingtyp 180 mV5
Input Shutdown Current ISHDNVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nF; Disabled, OUT = Open (Discharge Current Included)typ 0.1 · max 10 uA5
Input Quiescent Current IQVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nF; Enabled, OUT = Opentyp 300 uA5
Input Leakage Current ILEAKVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nF; Disabled, OUT Groundedtyp 0.1 · max 1 uA5
Reverse Leakage Current IREVTA = +25°C, CIN = 1uF, CL = 100nF; Disabled, VIN = 0V, VOUT = 5V, IREV at OUTtyp 0.5 · max 15 uA5
Reverse Leakage Current IREVTA = +25°C, CIN = 1uF, CL = 100nF; Disabled, VIN = 0V, VOUT = 20V, IREV at OUTtyp 0.5 · max 30 uA5
Overload Current Limit ILIMITAP22615; VIN = 5V, VOUT = 4V, RLIM = 1.94kΩ; TA = +25°C, CIN = 1uF, CL = 100nFmin 3.1 · typ 3.6 · max 4.2 A5
Overload Current Limit ILIMITAP22615; VIN = 5V, VOUT = 4V, RLIM = 6.8kΩ; TA = +25°C, CIN = 1uF, CL = 100nFmin 0.75 · typ 1 A5
Short-Circuit Current Limit ISHORTVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nF; Enabled, Output Short to Groundtyp 1 A5
Short-Circuit Response Time tSHORTVIN = 5V, No Load; TA = +25°C, CIN = 1uF, CL = 100nFtyp 5 us5
EN Input Logic Low Voltage VILVIN = 5V; TA = +25°C, CIN = 1uF, CL = 100nFmax 0.4 V5
EN Input Logic High Voltage VIHVIN = 5V; TA = +25°C, CIN = 1uF, CL = 100nFmin 1.2 V5
EN Input Leakage ILEAK-ENVIN = 5V, VEN = 0V and 5.5V; TA = +25°C, CIN = 1uF, CL = 100nFtyp 1 · max 2 uA5
Output Leakage Current ILEAK-OVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nF; Disabled, VOUT = 0Vtyp 0.5 · max 1 uA5
Output Turn-On Delay Time tD(ON)CL = 10uF, RLOAD = 10Ω @ VIN = 5V (Figure 1); TA = +25°C, CIN = 1uFtyp 2.2 ms5
Output Turn-On Rise Time tRCL = 10uF, RLOAD = 10Ω @ VIN = 5V (Figure 1); TA = +25°C, CIN = 1uFmin 1 · typ 1.9 · max 3.5 ms5
Output Turn-Off Delay Time tD(OFF)CL = 10uF, RLOAD = 10Ω @ VIN = 5V (Figure 1); TA = +25°C, CIN = 1uFtyp 0.02 ms5
Output Turn-Off Fall Time tFCL = 10uF, RLOAD = 10Ω @ VIN = 5V (Figure 1); TA = +25°C, CIN = 1uFtyp 0.2 ms5
FLG Output FET On-Resistance RFLGIFLG = 10mA; VIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFtyp 40 · max 60 Ω5
FLG Off Current IFOHVFLG = 5V; VIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFtyp 0.01 · max 1 uA5
FLG Blanking Time tBLANKAssertion or Deassertion due to Overvoltage, Overcurrent, and Overtemperature Condition; VIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFmin 2 · typ 7 · max 20 ms5
Discharge Resistance RDISVIN = 5V, Disabled, VOUT = 1V; TA = +25°C, CIN = 1uF, CL = 100nFtyp 100 Ω5
Thermal Shutdown Threshold TSHDNEnabled; VIN = 5.0V, CIN = 1uF, CL = 100nFtyp 140 °C5
Thermal Shutdown Hysteresis THYSVIN = 5.0V, CIN = 1uF, CL = 100nFtyp 35 °C5
Output OVP Lockout VOV_TRIPVOUT Rising Threshold; VIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFmin 5.5 · typ 5.7 · max 5.9 V5
Output OVP Lockout VOV_TRIPVOUT Falling Threshold; VIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFtyp 5.6 V5
Output OVP Hysteresis OUTHYSVIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFtyp 0.1 V5
OVP Response Time tOVPIOUT = 0.5A, CL = 1uF, VOUT from 5.5V to 6V; VIN = 5.0V, TA = +25°C, CIN = 1uFtyp 1 us5
Reverse-Voltage Comparator Trip Point VRVPVOUT - VIN; VIN = 5.0V, TA = +25°C, CIN = 1uF, CL = 100nFtyp 65 mV5

Pins, by the datasheet

6
1 OUT
Voltage Output Pin. · p. 3
2 GND
Ground Pin of the Circuitry. · p. 3
3 FLG
Overcurrent and overtemperature fault report; open-drain flag is active low when triggered. · p. 3
4 EN
Enable input, active low or active high. · p. 3
5 ISET
Set OCP current by attaching resistor; ILIM (A) = 6800/RLIM (Ω). · p. 3
6 IN
Voltage Input Pin. · p. 3

Open-source boards using it

1
  • 4 layers70 × 88 mmUSB2514B, the printed circuit board in 3D

    USB2514B

    Ryanharma/USB2514B

    USB Hub design project on Kicad => schematic + pcb layout (beginner)

    80 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AP22615AWU?

Yes. The symbol is Regulator_Linear:AP22615AWU and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AP22615AWU?

TSOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the AP22615AWU datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the AP22615AWU?

JLCPCB lists it as part C2680357, with 715 in stock; the sellers' links on this page open their listings.

What can replace the AP22615AWU?

Parts like it in the library: the TPS22918DBV by Texas Instruments, the TPS2553DBV by Texas Instruments, the AP2553W6 by Diodes Incorporated and the TPS27081ADDC by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AP22615AWU?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.