Skip to the content

Open-source KiCad boards

15 match “PICO_PADS”

Printed circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.

  • 2 layers160 × 100 mmPico euro, the printed circuit board in 3D

    Pico euro

    shabaz123/pico-eurocard

    This repository contains PCB Gerber files and bill of materials for a Pi Pico Eurocard Development Board. See James' Workshop Wednesday's Video which demonstrates the revision 2.0 board.

    150 parts19
  • 4 layers82.1 × 21 mmPico stretch2, the printed circuit board in 3D

    Pico stretch2

    jvanderberg/pico-stretch2

    An RP2350B dev board that breaks out all 48 GPIO pins while following the original Raspberry Pi Pico footprint for the first 20 pins on each side.

    70 parts2
  • 2 layers114.1 × 81.2 mmMacropad, the printed circuit board in 3D

    Macropad

    ConstantlyDying/Macropad_V1

    A wireless macropad with haptics!!, comes with 11 switches and 2 rotary encoders.

    49 parts4
  • 2 layers55 × 89.5 mmPad board, the printed circuit board in 3D

    Pad board

    veroxzik/pump-ac-conversion

    A hyper-specific collection of mods for converting Pump It Up arcade pads to expensive USB controllers.

    16 parts2GPL-3.0
  • 6 layers60 × 20.4 mmRp3a0-mini, the printed circuit board in 3D

    Rp3a0-mini

    CopperPilot/rpi-zero-2w-kicad

    KiCad port of jonny12375/rp3a0: Raspberry Pi Zero 2W's RP3A0 on a Pi Pico-sized board

    124 parts1
  • 2 layers54 × 86 mmCahoots, the printed circuit board in 3D

    Cahoots

    yourbuddyconner/cahoots

    A 54 × 86 mm two-layer board that a Raspberry Pi Pico 2 solders onto. Front: the raw 1.54" e-paper (Good Display GDEY0154D67) on its 24-pin flex, two tactile switches, the pin half of a magnetic pogo connector at the…

    46 parts1
  • 2 layers80 × 40 mmMOD-0011, the printed circuit board in 3D

    MOD-0011

    buildwithnoknok/module-I2C-picohub-MOD-0011

    noknok PicoHub (MOD-0011): Pico 2 W carrier with a USB-PD power manager (CH32X035), Qwiic ports, USB host port and mezzanine interface. Firmware MIT, hardware CC BY-SA 4.0.

    129 partsMIT
  • 6 layers14 × 101.5 mmMainboard revD, the printed circuit board in 3D

    Mainboard revD

    Mmrliu-gooooood/smart-pen-codex

    首次重建时先用kicad-cli sch export netlist --format kicadxml ...生成XML,再buildpcb。runchecks.sh固定使用可写/tmp XDG目录,不写只读home配置。没有原厂PDF或私有相机图片打包。

    102 parts
  • 2 layers40 × 40 mmTopaz's Board, the printed circuit board in 3D

    Topaz's Board

    picovrfbt/PicoVR-Trackers

    A Collection of trackers & Designs as well as documentation for PicoVR Trackers

    49 partsApache-2.0
  • 4 layers36.8 × 35.6 mmESCv4.3, the printed circuit board in 3D

    ESCv4.3

    runger1101001/roboesc_micro

    108 parts
  • 4 layers70 × 109.2 mmManafish, the printed circuit board in 3D

    Manafish

    Tropaion/Manafish_Mainboard

    The Manafish Mainboard is the main electronics board of the Manafish ROV. It replaces the Raspberry Pi 3B, the USB-connected Raspberry Pi Pico and the wiring between them with one board:

    127 partsAGPL-3.0
  • 2 layers36 × 36 mmNora b106-board, the printed circuit board in 3D

    Nora b106-board

    rain-1/nora-b106

    Minimum assembly is still U1 plus C1 (4.7 µF) and C2 (100 nF), with external regulated 3.3 V and SWD wires. Headers are optional. The module's 82 hidden LGA pads need controlled reflow/hot-plate assembly.

    15 parts
  • 4 layers70 × 70 mmPF233-CB1, the printed circuit board in 3D

    PF233-CB1

    sappystick/ARX

    58 parts
  • 2 layers25.4 × 52.1 mmFakeTecv5, the printed circuit board in 3D

    FakeTecv5

    mofosyne/roTec_pcb

    A low-cost nrf52 device, targeting cases that supports rotary encoder. Forked from jtljac's take on faketec v5

    35 parts17CERN-OHL-P-2.0