Skip to the content

Boards using the CC1200RHB

19 boards

Boards in 19 GitHub repositories, designed in KiCad, that use the CC1200RHB by Texas Instruments (-123dBm -40℃~+85℃ 1.25Mbps 164MHz~950MHz 16dBm 23mA 2V~3.6V 46mA 869.5MHz ISM、802.15.4 Power-on reset function、Supports RSSI function、Supports FEC function、CRC check function、Automatic response function、Automatic retransmission function SPI transceiver VQFN-32-EP(5x5) RF Transceiver ICs ROHS). See how each wires it, with its parts, size, README and files; the CC1200RHB’s symbol, footprint and pinout are on its own page.

  • 4 layers202 × 125 mmM17-rru rf, the printed circuit board in 3D

    M17-rru rf

    M17-Project/rru-rf-hw

    Remote Radio Unit - RF board

    241 parts47
  • 4 layers99.6 × 43.7 mmMini17, the printed circuit board in 3D

    Mini17

    M17-Project/Mini17

    Mini17 - QRP M17 handheld

    209 parts41
  • 4 layers65.1 × 30.2 mmCC1200 Hat, the printed circuit board in 3D

    CC1200 Hat

    M17-Project/CC1200_HAT-hw

    CC1200 HAT - RF board

    77 parts26
  • 2 layers57.2 × 57.2 mmRocketBeaconModule, the printed circuit board in 3D

    RocketBeaconModule

    explosion33/ArmLabRadio_PCB

    KiCad files for CC1200 based 2m / 70cm radio

    96 parts4
  • 6 layers90 × 45 mmHw tele stern, the printed circuit board in 3D

    Hw tele stern

    shorlee/TeleSTERN

    The TeleSTERN Project is an Open Source Rocketry Flight Computer based on the TeleMega by Altus Metrum.

    303 parts3GPL-3.0
  • 4 layers90 × 90 mmSahel pcb, the printed circuit board in 3D

    Sahel pcb

    Aliou8/SAHEL-SPECTRA-RF

    CubeSat for educational purposes. It is based on an STM32H7 MCU for data handling and uses two CC1125 radios for communication. The software is developed using a Zephyr-like RTOS.

    172 parts2GPL-3.0
  • 4 layers50 × 50 mmCC1200 Dev Board, the printed circuit board in 3D

    CC1200 Dev Board

    camstillo/Trail_Camera_v1

    Schematic and ordering information for trail camera device

    85 parts
  • 4 layers68.3 × 25.4 mmFlutter ARM R5 Basic, the printed circuit board in 3D

    Flutter ARM R5 Basic

    flutterwireless/kicad_conversion

    converting the Flutter main boards to KiCAD

    288 parts
  • 6 layers17.2 × 35.4 mmOshEasyMini, the printed circuit board in 3D

    OshEasyMini

    Kev1n8088/OshEasyMini

    124 parts
  • 4 layers30 × 80 mmOshTelemega, the printed circuit board in 3D

    OshTelemega

    Kev1n8088/OshTelemega

    The Mega3080 FCU is an evolved clone of the Altus Metrum Telemega. Using the same firmware (meaning the same sensor suite), the primary developments are: - USB-C - Wago style spring terminals - Better GPS RF routing…

    166 parts
  • 4 layers40 × 40 mmCc1120-dev, the printed circuit board in 3D

    Cc1120-dev

    mck1117/cc1120-dev

    183 parts
  • 4 layers45.7 × 23.7 mmCc1200, the printed circuit board in 3D

    Cc1200

    seanstone/cc1200

    46 parts
  • 4 layers50 × 30 mmCc1200-balloon, the printed circuit board in 3D

    Cc1200-balloon

    tmpk13/cc1200-balloon

    High altitude balloon payload: a CC1200 sub-GHz telemetry downlink and an air quality sensor stack, hosted by a Seeed Wio-E5 module. Four-layer 50 x 30 mm board, routed.

    108 partsMIT
  • 4 layers31 × 40 mmOSS Radio 2M70CM, the printed circuit board in 3D

    OSS Radio 2M70CM

    Arkos-Engineering/HT-15_hardware

    We can split this out into separate repos later, right now its very convenient to have everything here.

    112 parts72
  • 4 layers63.4 × 66.3 mmLTT, the printed circuit board in 3D

    LTT

    waterloo-rocketry/canhw

    Hardware monorepo avionics PCB

    110 parts15GPL-3.0
  • 4 layers35 × 55 mmCARP, the printed circuit board in 3D

    CARP

    aweeri/Control-Avionics-RP2350

    Control Avionics RP2350 [CARP] is a compact system designed specifically for operating small scale sounding rockets.

    96 parts2
  • 2 layersMini17, the printed circuit board in 3D

    Mini17

    kitspace-test-repos/kicad6-file-collection

    170 partsMIT