4 layers202 × 125 mm
CC1200RHB
Texas Instruments
-123dBm -40℃~+85℃ 1.25Mbps 164MHz~950MHz 16dBm 23mA 2V~3.6V 46mA 869.5MHz ISM、802.15.4 Power-on reset function、Supports RSSI function、Supports FEC function、CRC check function、Automatic response function、Automatic retransmission function SPI transceiver VQFN-32-EP(5x5) RF Transceiver ICs ROHS
Extended
- Category
- RF Transceiver ICs
- Package
- VQFN-32-EP(5x5)
- Pins
- 33
Overview
The CC1200RHB is a RF Transceiver IC made by Texas Instruments in a VQFN-32-EP(5x5) package with 33 pins. -123dBm -40℃~+85℃ 1.25Mbps 164MHz~950MHz 16dBm 23mA 2V~3.6V 46mA 869.5MHz ISM、802.15.4 Power-on reset function、Supports RSSI function、Supports FEC function、CRC check function、Automatic response function、Automatic retransmission function SPI transceiver VQFN-32-EP(5x5) RF Transceiver ICs ROHS.
PCBKit's library has its KiCad symbol (CC1200RHBT:CC1200RHBT, from Antmicro) and its footprint (Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm, from KiCad's library), ready for a KiCad board. 542 are in stock at JLCPCB (part C122881). 19 open-source boards in 19 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
14- Supply, least
- 2 V · VDD, AVDD_x, recommended operating min; all supply pins at the same voltage · p. 7
- Supply, most
- 3.6 V · VDD, AVDD_x, recommended operating max; all supply pins at the same voltage · p. 7
- Supply, absolute maximum
- 3.9 V · VDD, AVDD_x, absolute max · p. 7
- Works from
- -40 °C · Ambient operating min · p. 7
- Works up to
- 85 °C · Ambient operating max · p. 7
- Junction to case (RHB)
- 21.1 K/W · Junction-to-case top, 0.00 m/s airflow · p. 7
- Junction to board (RHB)
- 5.3 K/W · Junction-to-board, 0.00 m/s airflow · p. 7
- Junction to air (RHB)
- 31.3 K/W · Junction-to-free air, 0.00 m/s airflow · p. 7
- Takes working
- 23.5 mA · Typical RX packet reception, high-performance mode, 1.2 kbps; VDD = 3.0 V, TA = 25°C, fc = 869.5 MHz · p. 10
- Takes at most
- 54 mA · Typical TX at +15 dBm, 169-MHz band, high-performance mode; VDD = 3.0 V, TA = 25°C · p. 9
- Takes asleep
- 120 nA · Typical power down with retention; VDD = 3.0 V, TA = 25°C · p. 9
- Takes asleep
- 500 nA · Typical power down with retention, low-power RC oscillator running; VDD = 3.0 V, TA = 25°C · p. 9
- Data rate, most
- 1.25 Mbit/s · Packet mode max · p. 8
- Data rate, most
- 625 kbit/s · Transparent mode max · p. 8
What it is and has
8- Data FIFOs
- Separate 128-byte RX and TX · p. 1
- Modulation formats
- 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, MSK, OOK · p. 1
- Receiver sensitivity
- –123 dBm at 1.2 kbps · p. 1
- Receiver sensitivity
- –109 dBm at 50 kbps · p. 1
- Output power
- Programmable up to +16 dBm · p. 1
- Output power step
- 0.4 dB · p. 1
- SPI
- 4-wire, for configuration and data buffer access · p. 21
- Antenna diversity
- GPIO-controlled external antenna switch required · p. 22
Specifications
49| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage (VDD, AVDD_x) | All supply pins must have the same voltage | min -0.3 · max 3.9 V | 7 |
| Input RF level | max 10 dBm | 7 | |
| Voltage on any digital pin | max 3.9 V | min -0.3 V | 7 |
| Voltage on analog pins (including DCPL pins) | min -0.3 · max 2 V | 7 | |
| Storage temperature range Tstg | min -40 · max 125 °C | 7 | |
| Electrostatic discharge (ESD) performance VESD | Human body model (HBM), per ANSI/ESDA/JEDEC JS001 | min -2 · max 2 kV | 7 |
| Electrostatic discharge (ESD) performance VESD | Charged device model (CDM), per JESD22-C101; All pins | min -500 · max 500 V | 7 |
| Voltage supply range | All supply pins must have the same voltage | min 2 · max 3.6 V | 7 |
| Voltage on digital inputs | min 0 V | 7 | |
| Temperature range | Ambient | min -40 · max 85 °C | 7 |
| Junction-to-case (top) RθJC | RHB; airflow 0.00 m/s | typ 21.1 °C/W | 7 |
| Junction-to-board RθJB | RHB; airflow 0.00 m/s | typ 5.3 °C/W | 7 |
| Junction-to-free air RθJA | RHB; airflow 0.00 m/s | typ 31.3 °C/W | 7 |
| Junction-to-package top PsiJT | RHB; airflow 0.00 m/s | typ 0.2 °C/W | 7 |
| Junction-to-board PsiJB | RHB; airflow 0.00 m/s | typ 5.3 °C/W | 7 |
| Junction-to-case (bottom) RθJC | RHB; airflow 0.00 m/s | typ 0.8 °C/W | 7 |
| Frequency bands | min 820 · max 950 MHz | 8 | |
| Frequency bands | min 410 · max 475 MHz | 8 | |
| Frequency bands | min 164 · max 190 MHz | 8 | |
| Frequency bands | Contact TI for more information about the use of these frequency bands | min 274 · max 316.6 MHz | 8 |
| Frequency bands | Contact TI for more information about the use of these frequency bands | min 205 · max 237.5 MHz | 8 |
| Frequency bands | Contact TI for more information about the use of these frequency bands | min 137 · max 158.3 MHz | 8 |
| Frequency resolution | In 820–950 MHz band | typ 30 Hz | 8 |
| Frequency resolution | In 410–475 MHz band | typ 15 Hz | 8 |
| Frequency resolution | In 164–190 MHz band | typ 6 Hz | 8 |
| Data rate | Packet mode | min 0 · max 1250 kbps | 8 |
| Data rate | Transparent mode | min 0 · max 625 kbps | 8 |
| Power down with retention | TA = 25°C, VDD = 3.0 V | typ 0.12 · max 1 uA | 9 |
| Power down with retention | TA = 25°C, VDD = 3.0 V; Low-power RC oscillator running | typ 0.5 uA | 9 |
| XOFF mode | TA = 25°C, VDD = 3.0 V; Crystal oscillator / TCXO disabled | typ 180 uA | 9 |
| IDLE mode | TA = 25°C, VDD = 3.0 V; Clock running, system waiting with no radio activity | typ 1.5 mA | 9 |
| TX current consumption +14 dBm | TA = 25°C, VDD = 3.0 V | typ 46 mA | 9 |
| TX current consumption +10 dBm | TA = 25°C, VDD = 3.0 V | typ 36 mA | 9 |
| TX current consumption +15 dBm | TA = 25°C, VDD = 3.0 V | typ 49 mA | 9 |
| TX current consumption +10 dBm | TA = 25°C, VDD = 3.0 V | typ 35 mA | 9 |
| TX current consumption +15 dBm | TA = 25°C, VDD = 3.0 V | typ 54 mA | 9 |
| TX current consumption +14 dBm | TA = 25°C, VDD = 3.0 V | typ 50 mA | 9 |
| TX current consumption +10 dBm | TA = 25°C, VDD = 3.0 V | typ 39 mA | 9 |
| TX current consumption +10 dBm | TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 33.6 mA | 9 |
| RX Wait for sync | 1.2 kbps, 4-byte preamble (50 kHz Channel Filter Bandwidth); RX sniff mode; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 0.5 mA | 10 |
| RX Wait for sync | 1.2 kbps, 3-byte preamble (11 kHz Channel Filter Bandwidth); RX sniff mode; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 3.1 mA | 10 |
| RX Wait for sync | 38.4 kbps, 12-byte preamble; RX sniff mode; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 3.4 mA | 10 |
| RX Wait for sync | 50 kbps, 24-byte preamble; RX sniff mode; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 2.1 mA | 10 |
| RX Peak Current | 1.2kbps; Peak current consumption during packet reception; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 23.5 mA | 10 |
| Average current consumption | Check for data packet every 1 second using Wake on Radio; 50 kbps, 5-byte preamble, 40-kHz RC oscillator used as sleep timer; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 8 uA | 10 |
| RX Peak Current Low-power RX mode | 1.2 kbps; Peak current consumption during packet reception at the sensitivity limit; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ 19 mA | 10 |
| Saturation | TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz; BER limit 1% | typ 10 dBm | 10 |
| Digital channel filter programmable bandwidth | TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | min 9.5 · max 1600 kHz | 10 |
| IIP3 | At maximum gain; TA = 25°C, VDD = 3.0 V, fc = 869.5 MHz | typ -14 dBm | 10 |
Pins, by the datasheet
33- 1 VDD_GUARD
- 2.0–3.6 V VDD. · p. 6
- 2 RESET_N
- Asynchronous, active-low digital reset. · p. 6
- 3 GPIO3
- General-purpose I/O. · p. 6
- 4 GPIO2
- General-purpose I/O. · p. 6
- 5 DVDD
- 2.0–3.6 VDD to internal digital regulator. · p. 6
- 6 DCPL
- Digital regulator output to external decoupling capacitor. · p. 6
- 7 SI
- Serial data in. · p. 6
- 8 SCLK
- Serial data clock. · p. 6
- 9 SO(GPIO1)
- Serial data out (general-purpose I/O). · p. 6
- 10 GPIO0
- General-purpose I/O. · p. 6
- 11 CSn
- Active-low chip select. · p. 6
- 12 DVDD
- 2.0–3.6 V VDD. · p. 6
- 13 AVDD_IF
- 2.0–3.6 V VDD. · p. 6
- 14 RBIAS
- External high-precision resistor. · p. 6
- 15 AVDD_RF
- 2.0–3.6 V VDD. · p. 6
- 16 N.C.
- Not connected. · p. 6
- 17 PA
- Single-ended TX output; requires DC path to VDD. · p. 6
- 18 TRX_SW
- TX and RX switch; internally connected to GND in TX and floating in RX. · p. 6
- 19 LNA_P
- Differential RX input; requires DC path to ground. · p. 6
- 20 LNA_N
- Differential RX input; requires DC path to ground. · p. 6
- 21 DCPL_VCO
- External decoupling of VCO supply regulator. · p. 6
- 22 AVDD_SYNTH1
- 2.0–3.6 V VDD. · p. 6
- 23 LPF0
- External loop filter components. · p. 6
- 24 LPF1
- External loop filter components. · p. 6
- 25 AVDD_PFD_CHP
- 2.0–3.6 V VDD. · p. 6
- 26 DCPL_PFD_CHP
- External decoupling of PFD and CHP regulator. · p. 6
- 27 AVDD_SYNTH2
- 2.0–3.6 V VDD. · p. 6
- 28 AVDD_XOSC
- 2.0–3.6 V VDD. · p. 6
- 29 DCPL_XOSC
- External decoupling of XOSC supply regulator. · p. 6
- 30 XOSC_Q1
- Crystal oscillator pin 1; ground when using a TCXO or other external clock on EXT_XOSC. · p. 6
- 31 XOSC_Q2
- Crystal oscillator pin 2; leave floating when using a TCXO or other external clock on EXT_XOSC. · p. 6
- 32 EXT_XOSC
- External clock input; ground when using a regular crystal on XOSC_Q1 and XOSC_Q2. · p. 6
- – GND
- Ground pad; must connect to a solid ground plane. · p. 6
Ordering codes, by the datasheet
6- CC1200RHBR
- VQFN (RHB), 32 pins · 3000, LARGE T&R; NIPDAU or NIPDAUAG; -40 to 85 °C · p. 28
- CC1200RHBR.A
- VQFN (RHB), 32 pins · 3000, LARGE T&R; NIPDAU; -40 to 85 °C · p. 28
- CC1200RHBR.B
- VQFN (RHB), 32 pins · 3000, LARGE T&R; NIPDAU; -40 to 85 °C · p. 28
- CC1200RHBT
- VQFN (RHB), 32 pins · 250, SMALL T&R; NIPDAU or NIPDAUAG; -40 to 85 °C · p. 28
- CC1200RHBT.A
- VQFN (RHB), 32 pins · 250, SMALL T&R; NIPDAU; -40 to 85 °C · p. 28
- CC1200RHBT.B
- VQFN (RHB), 32 pins · 250, SMALL T&R; NIPDAU; -40 to 85 °C · p. 28
Parameters
20- Applications
- ISM
- Current - Supply
- 23.5mA
- Current - Supply(Max)
- 54mA
- Current Of Transmitting
- 46mA
- Data Rate
- 1.25Mbps
- Features
- Power-on Reset
- Frequency Range
- 164MHz~950MHz
- Interface
- SPI
- Operating Temperature
- -40℃~+85℃
- Output Power
- 16dBm
- Receive Current
- 23mA
- Sensitivity
- -123dBm
- Standby Current
- 120nA
- Thermal Resistance(Junction to Ambient)
- 31.3℃/W
- Thermal Resistance(Junction to Board)
- 5.3℃/W
- Thermal Resistance(Junction to Case)
- 21.1℃/W
- Type
- transceiver
- Typical Application Frequency
- 869.5MHz
- Voltage - Supply
- 2V~3.6V
- Voltage - Supply(Absolute Max)
- 3.9V
Order codes
2- CC1200RHBRLCSC C122881
- CC1200RHBTLCSC C201557
Pinout
33| Pin | Name | Type |
|---|---|---|
| 1 | VDD_GUARD | Power in |
| 2 | RESET | Input |
| 3 | GPIO3 | Input/output |
| 4 | GPIO4 | Input/output |
| 5 | DVDD | Passive |
| 6 | DCPL | Power out |
| 7 | SI | Input |
| 8 | SCLK | Input |
| 9 | SO(GPIO1) | Input/output |
| 10 | GPIO0 | Input/output |
| 11 | CS | Input |
| 12 | DVDD | Power in |
| 13 | AVDD_IF | Power in |
| 14 | RBIAS | Power in |
| 15 | AVDD_RF | Power in |
| 16 | NC | Not connected |
| 17 | PA | Passive |
| 18 | TRX_SW | Passive |
| 19 | LNA+ | Passive |
| 20 | LNA- | Passive |
| 21 | DCPL_VCO | Power in |
| 22 | AVDD_SYNTH1 | Power in |
| 23 | LPF0 | Passive |
| 24 | LPF1 | Passive |
| 25 | AVDD_PFD_CHP | Power in |
| 26 | DCPL_PFD_CHP | Power in |
| 27 | AVDD_SYNTH2 | Power in |
| 28 | AVDD_XOSC | Power in |
| 29 | DCPL_XOSC | Power in |
| 30 | XOSC_Q1 | Passive |
| 31 | XOSC_Q2 | Passive |
| 32 | EXT_XOSC | Input |
| 33 | EP | Power in |
Open-source boards using it
All 19- 4 layers99.6 × 43.7 mm
- 4 layers65.1 × 30.2 mm
- 2 layers57.2 × 57.2 mm
- 6 layers90 × 45 mm
Hw tele stern
shorlee/TeleSTERN
The TeleSTERN Project is an Open Source Rocketry Flight Computer based on the TeleMega by Altus Metrum.
303 parts3GPL-3.0 - 4 layers90 × 90 mm
Sahel pcb
Aliou8/SAHEL-SPECTRA-RF
CubeSat for educational purposes. It is based on an STM32H7 MCU for data handling and uses two CC1125 radios for communication. The software is developed using a Zephyr-like RTOS.
172 parts2GPL-3.0 - 4 layers76.2 × 25.4 mm
- 4 layers50 × 50 mm
CC1200 Dev Board
camstillo/Trail_Camera_v1
Schematic and ordering information for trail camera device
85 parts
Show this part on your page
<iframe src="https://pcbkit.io/embed/parts/ti/CC1200RHB" title="CC1200RHB in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe><img src="https://pcbkit.io/embed/parts/ti/CC1200RHB.jpg" alt="CC1200RHB" width="1200" height="900">[](https://pcbkit.io/parts/ti/CC1200RHB)Questions
Is there a KiCad symbol and footprint for the CC1200RHB?
Yes. The symbol is CC1200RHBT:CC1200RHBT and the footprint Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the CC1200RHB?
VQFN-32-EP(5x5), with 33 pins. Its footprint is drawn on this page.
Where is the CC1200RHB datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the CC1200RHB?
JLCPCB lists it as part C122881, with 542 in stock; the sellers' links on this page open their listings.
What can replace the CC1200RHB?
Parts like it in the library: the ESP8266EX by Espressif Systems and the NRF8001-R2Q32-T by Nordic Semicon. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the CC1200RHB?
19 boards in 19 repositories on GitHub; the most starred are listed on this page, with their KiCad files.
Parts like it
2
ESP8266EX
QFN-32-EP(5x5)-40℃~+125℃ -91dBm 120mA 2.4GHz 2.4GHz~2.4835GHz 2.5V~3.6V 21.5dBm 50mA 72.2Mbps SPI、UART、I2C、I2S WiFi transceiver QFN-32-EP(5x5) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICsNRF8001-R2Q32-T
QFN-32-EP(5x5)-40℃~+85℃ -87dBm 0dBm 1.9V~3.6V 1Mbps 2.4GHz Bluetooth SPI、UART、I2C QFN-32-EP(5x5) RF Transceiver ICs ROHSNordic SemiconRF Transceiver ICs