Skip to the content

Boards using the MS561101BA03-50

20 boards

Boards in 18 GitHub repositories, designed in KiCad, that use the MS561101BA03-50 by TE Connectivity (-40℃~+85℃ 1.8V~3.6V 140nA 150pa 1Kpa~1.2bar 8.22ms I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output Yes QFN-8(3x5) Pressure Sensors ROHS). See how each wires it, with its parts, size, README and files; the MS561101BA03-50’s symbol, footprint and pinout are on its own page.

  • 2 layers136.2 × 85.9 mmBATDATUNIT01, the printed circuit board in 3D

    BATDATUNIT01

    mlab-modules/BATDATUNIT01

    Multiple parallel Li-ion 18650 battery cell module with BMS and data storage with MCU control.

    225 parts5GPL-3.0
  • 4 layers70 × 40 mmFlight comp srad-2026, the printed circuit board in 3D

    Flight comp srad-2026

    vito-pp/FlightComputer-SRAD-2026

    HW and SW documentation of a Student Researched And Developed (SRAD) flight computer in charge of telemetry for ITBA's rocketry team 2026

    86 parts3
  • 4 layers101.6 × 26.9 mmLiaka V3, the printed circuit board in 3D

    Liaka V3

    LulaUAV/Laika-Flight-Computer

    Kicad files for the Laika flight computer

    81 parts2
  • 4 layers91 × 30.1 mmStrelka Flight Computer, the printed circuit board in 3D

    Strelka Flight Computer

    LulaUAV/Strelka-Flight-Computer

    Strelka exists in the family of rocket dog flight computers. This flight computer is fully capable of deploying recovery events.

    170 parts2
  • 4 layers50 × 75 mmOneroiV1, the printed circuit board in 3D

    OneroiV1

    HomeOnDuna/Nyx-Flight-Computers

    Contains the Nyx flight computer family developed for UNSW Rocketry Avionics team.

    166 parts1
  • 4 layers38.4 × 82.8 mmHorizon, the printed circuit board in 3D

    Horizon

    ChladpavPy/Horizon

    Custom Rocket Flight Controller

    99 parts
  • 4 layers44.5 × 44.5 mmQUT Autopilot Pixracer, the printed circuit board in 3D

    QUT Autopilot Pixracer

    Heckus/QUT-OpenFCU

    The primary objective is to create an alternative to the difficult-to-source off-the-shelf Pixhawk 6. This work builds upon a edited pixracer version produced by KAI (Wesley) in 2022.

    145 parts
  • 6 layers40 × 40 mmKestrel fc, the printed circuit board in 3D

    Kestrel fc

    HeyPCB/kestrel-fc

    Kestrel H7: STM32H743 FPV flight controller with ICM-20602 + BMI088, MS5611, 16 MB blackbox, 5 V and switchable 10 V BECs.

    114 partsCERN-OHL-S-2.0
  • 6 layers40 × 40 mm20x20 fc, the printed circuit board in 3D

    20x20 fc

    lmiez/yecnodF405

    Open source flight controller based on the STM32F405 MCU that runs betaflight.

    120 partsGPL-3.0
  • 4 layers80 × 60.6 mmEsp extension, the printed circuit board in 3D

    Esp extension

    Miky8745/HalfLife-Drone

    It's an extension for an ESP32 S3 that allows it to safely control 4 coreless DC motors and get data from an IMU and Barometer units. Meaning it's prepared to be used in a quadcopter. And a frame for the drone itself.

    66 parts
  • 4 layers46 × 238 mmAssembly review, the printed circuit board in 3D

    Assembly review

    OAK-WJR/rocket-flight-computer

    Amateur rocket flight computer: single-board KiCad PCB (STM32H743), firmware and diagnostics

    208 parts
  • 4 layersControl Systems, the printed circuit board in 3D

    Control Systems

    Ryerson-Rocketry/Canards-PCB

    PCB for Canards

    122 parts
  • 2 layers65 × 65.5 mmSchmatic, the printed circuit board in 3D

    Schmatic

    Yorha-7/Rocket

    in this repo we are simulating rocket basic physics and make a onboard flight computer which utilizes MCU, gyro, pressure sensor, fin servo controls, to get realtime target tracking abilities to a solid fuel rocket.

    77 parts
  • 6 layers100.2 × 63.5 mmXavier NX IO Shield, the printed circuit board in 3D

    Xavier NX IO Shield

    ApotheoTech/APT-XAV-PX4

    A PX4 based Xavier NX flight controller

    309 parts2GPL-3.0
  • 2 layers36.7 × 75 mmIrisV1, the printed circuit board in 3D

    IrisV1

    HomeOnDuna/Nyx-Flight-Computers

    Contains the Nyx flight computer family developed for UNSW Rocketry Avionics team.

    93 parts1
  • 2 layers49.5 × 71.5 mmCNC PCB, the printed circuit board in 3D

    CNC PCB

    Terrapin-Rocket-Team/Payload

    Code and PCBS for the payload team

    17 parts1MIT
  • 4 layers50 × 50 mmMCU Board 0.1, the printed circuit board in 3D

    MCU Board 0.1

    thejamesrhodes/Hyades-Flight-Computer

    Full Hardware and Electronics design, Bare-metal GNC flight software for an actively attitude-controlled high-power rocket

    80 parts1Apache-2.0
  • 4 layers46 × 186 mmM3 assy r1, the printed circuit board in 3D

    M3 assy r1

    OAK-WJR/rocket-flight-computer

    Amateur rocket flight computer: single-board KiCad PCB (STM32H743), firmware and diagnostics

    135 parts
  • 4 layers58.9 × 58.9 mmNavPoTS Bridge, the printed circuit board in 3D

    NavPoTS Bridge

    RuberDuck9/NavPoTS

    74 partsAGPL-3.0