Skip to the content

Boards using the MMBT3906LT1G

17 boards

Boards in 16 GitHub repositories, designed in KiCad, that use the MMBT3906LT1G by onsemi (-55℃~+150℃ 1 PNP 200mA 225mW 250MHz 250mV 40V 50nA 5V 60 PNP SOT-23 Bipolar (BJT) ROHS). See how each wires it, with its parts, size, README and files; the MMBT3906LT1G’s symbol, footprint and pinout are on its own page.

  • 6 layers100 × 120 mmAstra piNas, the printed circuit board in 3D

    Astra piNas

    jlcjak/astra_piNas

    Six-layer CM5 Lite dual-NVMe carrier with PCIe switch, Ethernet, microSD, USB-C PD and PoE. Review design; fabrication hold documented.

    176 parts30
  • 2 layers162 × 90 mmDJetECUTester, the printed circuit board in 3D

    DJetECUTester

    ajayre/djetecutesterv2

    D-Jetronic ECU Tester V2

    160 parts2
  • 2 layers56 × 47 mmUlp flasher, the printed circuit board in 3D

    Ulp flasher

    LieBtrau/ultra-low-power-led-flasher

    ATtiny13 firmware to drive the flasher

    56 parts2GPL-3.0
  • 4 layers110 × 90 mmURC, the printed circuit board in 3D

    URC

    spikonado/URC

    Universal Robot Controller

    180 parts2CERN-OHL-W-2.0
  • 2 layers100 × 75 mmPowerBox PCB, the printed circuit board in 3D

    PowerBox PCB

    Alvin-Alford/PowerBox

    Add Later

    113 parts1
  • 4 layers101 × 51.5 mmQuack core, the printed circuit board in 3D

    Quack core

    HeyPCB/quack-core

    Brain board for the Open Duck Mini: Pi Zero 2W carrier, 14-servo STS bus, fused 2S power path in stitched copper zones (15-18 A battery side), USB-C charging with balancing, IMU.

    138 parts1CERN-OHL-S-2.0
  • 2 layers34 × 32.5 mmDyno, the printed circuit board in 3D

    Dyno

    drewradcliff/dyno

    Finger strength dynamometer

    21 partsMIT
  • 2 layers100 × 100 mmOpamp, the printed circuit board in 3D

    Opamp

    gallicchio/op-amp-pcb

    The op-amp of Learning the Art of Electronics (Hayes and Horowitz, 2016), Lab 5L, built from six 2N3904 / 2N3906 transistors on a 100 x 100 mm board whose silkscreen is the schematic.

    65 parts
  • 4 layers64 × 80 mmIris brainstem, the printed circuit board in 3D

    Iris brainstem

    HeyPCB/iris-brainstem

    Iris Brainstem: power and servo hub of the Iris robot head. 9 V USB-C PD in, 6 V / 5 A servo rail in stitched copper zones (measured), 5 V rail, half-duplex servo bus with ten ports, speaker amp.

    97 partsCERN-OHL-S-2.0
  • 2 layers32.1 × 50 mmBike voltage regulator rectifier, the printed circuit board in 3D

    Bike voltage regulator rectifier

    indoor-industry/bike_voltage_regulator-rectifier

    Schematic, PCB and case of a regulator-rectifier for batteryless single-wire stator motorbikes

    29 parts
  • 2 layers30 × 30 mmEce souvenir, the printed circuit board in 3D

    Ece souvenir

    patthananb/ECE_Openhouse_Souvenir

    KiCad design for ECE OPEN HOUSE 2026

    29 parts
  • 2 layers54.9 × 58.4 mmIR Digipot, the printed circuit board in 3D

    IR Digipot

    sergeyvfx/IR-Volume-Control

    Digipot volume control using IR controller

    134 partsMIT
  • 4 layers64 × 115 mmAmp board, the printed circuit board in 3D

    Amp board

    splogdes/Audio-Engine-A5-Input-Stage

    198 parts
  • 4 layers69.4 × 23.1 mmA1185 BMS Board, the printed circuit board in 3D

    A1185 BMS Board

    the-electron-vault/Apple

    172 parts12
  • 4 layers85 × 78 mmPod, the printed circuit board in 3D

    Pod

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    35 parts3MIT
  • 4 layers130 × 90 mmProgrammable usb2 hub, the printed circuit board in 3D

    Programmable usb2 hub

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    218 parts3MIT