Skip to the content

Boards using the IRM-05-5

18 boards

Boards in 17 GitHub repositories, designed in KiCad, that use the IRM-05-5 by MW (0.1W 120V~430V 1A 200mVp-p 21.5mm 25.4mm 3kV 45.7mm 5V 5W 71% 85VAC~305VAC AC/DC-DC Short Circuit Protection、Over Current Protection、Overvoltage protection ±2.5% DIP,45.7x25.4mm Power Module/Power Supply ROHS). See how each wires it, with its parts, size, README and files; the IRM-05-5’s symbol, footprint and pinout are on its own page.

  • 2 layers120 × 67 mmSilvia pid board, the printed circuit board in 3D

    Silvia pid board

    haydenridd/silvia-pid-board

    The following outlines: - Board circuit design - Hookup/wiring guide - Board mounting - BOM/Fabrication info

    39 parts10MIT
  • 2 layers126 × 57 mmMini Oven Controller, the printed circuit board in 3D

    Mini Oven Controller

    MAWoodMain/ESP-Reflow-Oven

    A retro fit of a Lidl middle aisle mini oven into a home reflow oven

    46 parts2MIT
  • 2 layers51.5 × 92 mmEcoport bridge v1, the printed circuit board in 3D

    Ecoport bridge v1

    jrowe88/ecoport-bridge

    CTA-2045 (EcoPort) bridge for a Rinnai REHP65 heat pump water heater

    74 parts1AGPL-3.0
  • 2 layers250 × 100 mmIroutlet, the printed circuit board in 3D

    Iroutlet

    bgs72/iroutlet

    The project consists of three major folders:

    66 parts
  • 2 layers55 × 96 mmMrReflow, the printed circuit board in 3D

    MrReflow

    C3MA/MrReflow

    To achieve that, readings from a thermocouple are used for closed loop temperature control of the target board. The controller does it's best to follow a preconfigured temperature profile for a particular SMT soldering.

    28 partsGPL-3.0
  • 2 layersApoce, the printed circuit board in 3D

    Apoce

    ckl67/apoce

    APOCE : Arduino Pilote pour Optimiser la gestion de Consommation Electrique

    38 parts
  • 2 layers142.2 × 106.7 mmSwitchFoil, the printed circuit board in 3D

    SwitchFoil

    falue/rebekkaSwitchFoil

    This repo is using a HLK-LD2450 microwave human presence sensor and a Sparkfun Thing Plus. This uses Micropython. See below for instructions to set it up.

    31 parts
  • 2 layers54.5 × 104.5 mmReflowOven, the printed circuit board in 3D

    ReflowOven

    gevanisko/ReflowOven

    Contains schematics, design and code for a toaster oven based solder reflow oven

    17 parts
  • 2 layers212 × 84 mmEurorack psu, the printed circuit board in 3D

    Eurorack psu

    ghosty141/eurorack-psu

    40 partsCERN-OHL-S-2.0
  • 4 layers102.6 × 148 mmLoRa Monitor, the printed circuit board in 3D

    LoRa Monitor

    m-scasserra/TrabajoFinal_MIoT

    242 parts
  • 2 layers75.6 × 81.9 mmAccessController, the printed circuit board in 3D

    AccessController

    minsk-hackerspace/accessController

    Control access to BIG DANGEROUS tools in hackerspace

    36 parts
  • 4 layers100 × 100 mmWattwiser, the printed circuit board in 3D

    Wattwiser

    rndfm/wattwiser_pcb

    49 parts
  • 2 layers72 × 68 mmCarbentra, the printed circuit board in 3D

    Carbentra

    hicancan/carbentra-smart-plug

    CARBENTRA smart plug: AIoT edge device for campus energy orchestration

    36 parts1AGPL-3.0
  • 2 layers100 × 100 mmBackplane DC, the printed circuit board in 3D

    Backplane DC

    AHWV/HBridge_HFreq_HVolt_r0

    19 parts
  • 2 layers60 × 100 mmAnalogPCB, the printed circuit board in 3D

    AnalogPCB

    dwynnychuk/SmartSmoker

    Upgrades for Traeger to add smart capability

    60 parts
  • 2 layers160 × 110 mmPumpengruppe rs485, the printed circuit board in 3D

    Pumpengruppe rs485

    freezweb/de.freezweb.heizungssteuerung

    Dieses Verzeichnis enthaelt den KiCad-Startentwurf fuer die dezentrale Pumpengruppen-Platine:

    112 parts
  • 4 layers100 × 100 mmWattwiser, the printed circuit board in 3D

    Wattwiser

    rndfm/wattwiser_pcb

    47 parts