Skip to the content

Interfaces and adapters

7,328 boards
  • 4 layers42.5 × 28 mmSTM32-QSPI Flash Board, the printed circuit board in 3D

    STM32-QSPI Flash Board

    FarahCelebi/STM32-QSPI-Flash-Board

    High-speed QSPI interface board — STM32 reading/writing an external QSPI NOR flash chip, with controlled-impedance and length-matched routing.

    18 partsMIT
  • 2 layers54 × 64 mmTla probe sma breakout, the printed circuit board in 3D

    Tla probe sma breakout

    farlepet/tek-tla-probes

    Logic probes for Tektronix logic analyzers (specifically TLA5200 series)

    51 partsGPL-3.0
  • 2 layers209.6 × 120.7 mmChb inverter, the printed circuit board in 3D

    Chb inverter

    feaksel/chb-inverter

    5-Level Cascaded H-Bridge Inverter (ELE 401/402 graduation project, Hacettepe University EEE) — modular CHB topology, STM32 F303RE firmware, PySide6 dashboard. Hardware fabricated and bench-validated.

    95 partsApache-2.0
  • 2 layers50 × 18 mmCan nano shield, the printed circuit board in 3D

    Can nano shield

    feastorg/can-nano-shield

    A compact Arduino Nano shield with MCP2515 & TJA1051/3 for easy CAN bus integration. Work-in-progress.

    24 partsGPL-3.0
  • 2 layers55.9 × 105.4 mmC5g pmod adapter, the printed circuit board in 3D

    C5g pmod adapter

    felipebalbi/c5g-pmod-adapter

    Cyclone V GX Starter Kit PMOD Adapter Board

    11 partsCERN-OHL-W-2.0
  • 2 layers30 × 30 mmSerial to UPDI, the printed circuit board in 3D

    Serial to UPDI

    fenilchandarana/serial-to-UPDI

    Serial to UPDI converter where you can upload the code and read the data through serial monitor without reconnecting pins

    5 partsCC0-1.0
  • 2 layers40 × 38.1 mmDc dc-3-3V RT8259GE, the printed circuit board in 3D

    Dc dc-3-3V RT8259GE

    Fescron/Project-LabAnalogDesign2

    Project-LabAnalogDesign2

    27 parts
  • 2 layers90 × 80 mmKanalog jp12-breakout, the printed circuit board in 3D

    Kanalog jp12-breakout

    festlv/kanalog-jp12-breakout

    Breakout board for KFlop's Kanalog JP12 (adds 8 inputs, 8 outputs to Kanalog)

    103 parts
  • 2 layers58.9 × 29.5 mmRn52-breakout, the printed circuit board in 3D

    Rn52-breakout

    festlv/rn52-breakout

    RN52 Bluetooth module breakout board

    18 partsMIT
  • 2 layers22.9 × 22.9 mmSe050-adapter, the printed circuit board in 3D

    Se050-adapter

    fgervais/se050-adapter

    10 parts
  • 2 layers7.6 × 5.1 mmBreakout, the printed circuit board in 3D

    Breakout

    fifteenhex/nortools-breakout

    Solder down breakout connector for SPI NOR

    2 partsGPL-3.0
  • 2 layers130 × 115 mmObd2-simulator, the printed circuit board in 3D

    Obd2-simulator

    FilipRaic/obd2-simulator

    Open-source OBD-II simulator board: emulates a vehicle ECU per SAE J1979 and ISO 15031-5 over CAN. ESP32-S3 + MCP2515, 21 simulated parameters, DTC bank with MIL.

    107 partsMIT
  • 2 layers18.5 × 17.8 mmNrf24-breakout, the printed circuit board in 3D

    Nrf24-breakout

    filipsalo/nrf24-breakout

    A simple little 18x19mm breakout board to make the NRF24L01+ RF tranceiver reasonably breadboard-friendly.

    8 parts
  • 2 layers83.3 × 58.1 mmQfn programmer, the printed circuit board in 3D

    Qfn programmer

    finnhittson/PCB-Business-Card

    This repo contains all information needed to make a PCB business card. The card features NFC IC that allows users to tap their phone and receive the stored data on the card.

    10 parts
  • 4 layers15.6 × 31.3 mmPIC32Flex, the printed circuit board in 3D

    PIC32Flex

    finnhittson/PIC32-Breakout-Board

    PIC32Flex is a breakout board for the PIC32MX170F256B. This repo holds schematic revision information, how to fabricate this board for yourself, and examples on how to use the board.

    14 parts
  • 4 layers34.4 × 12.7 mmUsb uart plug, the printed circuit board in 3D

    Usb uart plug

    Finomnis/usb-uart-plug

    A cable termination that converts a USB-C into USB+UART pads

    22 partsMIT
  • 4 layers94.5 × 80.5 mmReboostV2.1 fixed, the printed circuit board in 3D

    ReboostV2.1 fixed

    fl4p/dcdc-parasitics

    KiCad → FastHenry extractor for half-bridge power-stage parasitics (commutation-loop L, common-source inductance, gate-loop L/R) → SPICE subckt + SVG schematic

    184 parts
  • 4 layers145 × 80 mmShunt reversal freerouting source, the printed circuit board in 3D

    Shunt reversal freerouting source

    fl4p/shunt-reversal

    MOSFET H-bridge current-reversal switch for shunt thermal-EMF cancellation. Script-generated KiCad. NOT RELEASED - see DESIGN.md section 12.

    100 parts
  • 4 layers35 × 29 mmHdmi breakout, the printed circuit board in 3D

    Hdmi breakout

    flaviut/ceclink

    The CECLink is a small device that can be used to allow a Linux computer to control a TV using the CEC protocol over HDMI.

    6 parts
  • 2 layers17.5 × 33 mmLogic breakout, the printed circuit board in 3D

    Logic breakout

    florolf/electronics-utils

    Little helpers

    12 partsCC0-1.0