Skip to the content
2 layers83.3 × 58.1 mmQfn programmer, the printed circuit board in 3D

This repo contains all information needed to make a PCB business card. The card features NFC IC that allows users to tap their phone and receive the stored data on the card.

Size
83.3 × 58.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
7
Pads
36
Tracks, vias
40, 5
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
26 Jul 2026
Updated
26 Jul 2026

Overview

Qfn programmer is an open-source printed circuit board by finnhittson, from the finnhittson/PCB-Business-Card repository on GitHub. It is a 2-layer board of 83.3 × 58.1 mm with 10 parts on 7 nets, routed with 40 tracks and 5 vias.

It is built around the NT3H2111W0FHKH. Its parts include 2 connectors, 1 capacitor, 1 resistor, 1 IC and 1 diode. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

PCB Business Card

This repo contains all information needed to make a PCB business card. The card features NFC IC that allows users to tap their phone and receive the stored data on the card. Ideally this card is used at recruiting events to share a resume or a portfolio while also demonstrating one’s ability to make such a card. It also doubles as a fun way to rick roll your friends. This repo has a template for users to make their own PCB business card using the KiCad files in the electrical/ directory and the necessary software to configure the NFC tag in the software/ directory. The image below is my personal business card, but this repo also contains steps I took to make these cards in bulk. To see a demonstration of these cards working see this link and to see different designs see this link. card

Electrical

The schematic for the business card is very simple consisting of 5 devices. There is a resistor and LED to add effect and ambiance to the PCB and show the result of effective energy harvesting. There is a capacitor to store energy from the coil antenna. And finally, there is the NFC IC which is responsible for harvesting the energy captured by the coil, storing the data in EEPROM, and communicating with the phone. The following is the schematic for the card drawn in KiCad. card-schematic The IC used for this is the NT3H2111W0FHKH. The most engineeringly complex part of this card is the design of the antenna. The antenna effectively is an inductor that captures the magnetic field radiated from the phone. The phone generates an oscillating magnetic field at 13.56MHz and the capacitor on the IC forms a resonant take with the inductor to maximize energy captured. Thus, to design the antenna you can use the LC resonance formula below to calculate the value of inductance required. The datasheets recommends using a 220pF capacitor and with the frequency set to 13.56MHz we can rearrange and calculate the value for L.

$f_0=\frac{1}{2\pi\sqrt{LC}}$

Going through the math it is roughly 626nH. Next is to design the physical shape of the antenna and make sure it has 626nH of inductance. There are many inductor calculators online, but I found this one to be most helpful. This calculator lets you give dimensions for your antenna which is very helpful since we want this on a PCB with credit card dimensions. The next thing is to make a footprint with the same dimensions that the antenna calculator created. The image below is an image of the antenna laid out on a PCB template. card-layout With the PCB you can then modify the front and back silkscreen to have your name, phone number, and title. The backside can then have an image in which you can integrate an LED to add a cool effect.

Software

Annoyingly the NT3H2111W0FHKH IC come off the fab line in a read only state. I learned this the hard way when I soldered all my devices to my PCB card and couldn't write to it. To fix this I made another PCB to act as my programmer board that would unlock the ICs and then I would solder these unlocked ICs to the business cards. I wanted to use the smallest IC's possible, so the package type is an 8 pin QFN style package which is mighty small. I hot air gunned the IC to the PCB then programmed it using an Arduino as shown in the image below. programmer What the Arduino code is setting is the capability container (CC), described on page 25 of the datasheet, to have read and write access. This is done by setting the registers outlined in Table 8. This gives the CC register read write access. table8 However, because of the way memory is organized in this IC, caution needs to be taken so that you do not change other settings. When reading and writing to these registers you can only read and write to an entire page which contains more information than you need. A page at 16 bytes and we only need to modify 4 at a time. Therefore, the software reads a page, modifies the 4 bytes while leaving the other 12 unchanged, and then writes the entire page back to memory. Another caveat is that in enabling read write access for CC, the I2C address changes from 0x55 to 0x02 and you need to repeat the process twice; once for the 0x55 address and once for the 0x02 address. I found it easiest to start with the 0x55 address, verify the device was visible on the I2C bus, write my data, and repeat the process. I knew the write was successful if when I checked the I2C bus again I would see a device at 0x02 and no other address.

Once all of this was done and the unlocked IC is soldered to the board, I used NFC Tools app to program the IC to either my resume, linked account, or this link.

Parts

10
QtyValueFootprintReferences
4MountingHoleMountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH1, H2, H3, H4
2Conn_01x05_PinConnector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_VerticalJ1, J2
1220pCapacitor_SMD:C_0805_2012MetricC1
147Resistor_SMD:R_0805_2012MetricR1
1LEDLED_SMD:LED_0805_2012MetricD1
1NT3H2111W0FHKHcard:QFN8P50_160X160X50L40X20NU1

More from finnhittson/PCB-Business-Card

1
  • 2 layers85.6 × 54 mmCard template, the printed circuit board in 3D

    Card template

    finnhittson/PCB-Business-Card

    This repo contains all information needed to make a PCB business card. The card features NFC IC that allows users to tap their phone and receive the stored data on the card.

    5 parts

Similar boards

  • 2 layers85.4 × 54.1 mmBusiness Card v2, the printed circuit board in 3D

    Business Card v2

    WiHarper/nfc-card

    Open-Source Active PCB Business Card Powered by NFC

    39 parts105
  • 4 layers150 × 50 mmEmber, the printed circuit board in 3D

    Ember

    notaroomba/ember

    A custom hot plate powered by USB-C Power Delivery.

    136 parts25
  • 2 layers95.9 × 95 mmHnr26-badge, the printed circuit board in 3D

    Hnr26-badge

    nushackers/hnr26-badge-quacknroll

    Hack&Roll 2026 "Quack & Roll" badge source files, for both hardware and firmware

    77 parts8
  • 2 layers63.5 × 88.9 mmCHEAPSUITS, the printed circuit board in 3D

    CHEAPSUITS

    geg-tech/cheapsuit

    a NFC PCB card with a cyberpunk/poker aesthetic

    36 parts3
  • 2 layers93.2 × 100 mmBadge dragonJar-2025, the printed circuit board in 3D

    Badge dragonJar-2025

    ElectronicCats/badge-dragonJar-2025

    ¡El badge oficial de DragonJarCON 2025! Un dispositivo NFC programable con pantalla OLED, múltiples LEDs y un reto de hacking integrado. Diseñado para la comunidad de DragonJar

    66 parts2
  • 2 layers99.6 × 49.8 mmStasis badge, the printed circuit board in 3D

    Stasis badge

    MeghanaM4/stasis-badge

    74 parts2
  • 2 layers85.1 × 53.3 mmBusinessCard, the printed circuit board in 3D

    BusinessCard

    ACW-Electronics/PCB-Business-Card

    Making an NFC PCB Business Card

    6 parts1

Questions

How big is the Qfn programmer PCB?

It measures 83.3 × 58.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Qfn programmer use?

10 parts, built around the NT3H2111W0FHKH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Qfn programmer KiCad files?

From the finnhittson/PCB-Business-Card repository on GitHub, at the commit this page was made from: the board is electrical/qfn-programmer/qfn-programmer.kicad_pcb and its schematic electrical/card-template/card-template.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Qfn programmer design in my own project?

Its repository states no licence, so its author keeps all rights: ask finnhittson before reusing the design.