Skip to the content

Boards by WRansohoff

9 boards

Open-source boards designed in KiCad by WRansohoff on GitHub, from 8 repositories. A board’s address here is its repository’s there.

  • 2 layers17.8 × 30.5 mmSTM32L422KB LiPo, the printed circuit board in 3D

    STM32L422KB LiPo

    WRansohoff/STM32_LiPo_Example

    Simple lithium battery-powered STM32 board using an MCP73831 for charging.

    29 parts17MIT
  • 2 layers25.4 × 25.4 mmSSD1306 SPI Breakout, the printed circuit board in 3D

    SSD1306 SPI Breakout

    WRansohoff/OLED_test_boards

    Repository with KiCAD projects for two boards which provide SPI communication to a 30-pin 128x64 monochrome SSD1306 display panel, and a 23-pin 96x64 multicolor SSD1331 one.

    18 parts16MIT
  • 2 layers18.4 × 20.3 mmCP2102N bb, the printed circuit board in 3D

    CP2102N bb

    WRansohoff/CP2102N_simple

    Simple breakout board for a CP2102N USB / UART bridge.

    18 parts9MIT
  • 2 layers92.3 × 50.2 mmMotoMate, the printed circuit board in 3D

    MotoMate

    WRansohoff/MotoMate

    An STM32-based GPS receiver handheld board with a small display and microSD card slot: eventually, I'd like to make some simple mapping / logging firmware and a case for mounting it to motorcycle handlebars.

    63 parts1MIT
  • 2 layers17.8 × 38.1 mmSTM32G031Kx bb, the printed circuit board in 3D

    STM32G031Kx bb

    WRansohoff/STM32G031Kx_bb

    Simple open-source breakout board for a 32-pin STM32G031 microcontroller. Designed to be easy to hand-solder, with wide footprints and no parts smaller than 0805. Feedback is welcome!

    16 parts1MIT
  • 4 layers64.1 × 72.4 mmStm32 linux, the printed circuit board in 3D

    Stm32 linux

    WRansohoff/Magrat_v0

    Design files and test firmwares for a single-core STM32H7 board with extra RAM and a side of Flash.

    78 partsMIT
  • 2 layers21 × 17.8 mmMax31855 bb, the printed circuit board in 3D

    Max31855 bb

    WRansohoff/MAX31855_breakout

    Simple OSHW breakout board for a MAX31855 thermocouple amplifier chip.

    8 partsMIT
  • 2 layers54 × 85.7 mmSTEAMGal STM32F051Kx, the printed circuit board in 3D

    STEAMGal STM32F051Kx

    WRansohoff/STEAMGal_Tetris

    Try writing some 'tetris' firmware for a development board with a very small display, a buzzer, and a few buttons. That should introduce a few core peripherals.

    63 partsMIT
  • 2 layers25.4 × 25.4 mmSSD1331 SPI Breakout, the printed circuit board in 3D

    SSD1331 SPI Breakout

    WRansohoff/OLED_test_boards

    Repository with KiCAD projects for two boards which provide SPI communication to a 30-pin 128x64 monochrome SSD1306 display panel, and a 23-pin 96x64 multicolor SSD1331 one.

    14 parts16MIT