
Open-source KiCad boards
107,410 boardsPrinted circuit boards designed in KiCad and published on GitHub, each with its parts, layers and size, its README and its files; open any of them in PCBKit.
- 2 layers76.5 × 38.1 mm

- 2 layers29.8 × 70.5 mm

- 2 layers45.7 × 38.1 mm

- 2 layers75 × 66 mm

- 2 layers46.7 × 40.9 mm

CASIO VX4 YM2413 Soundcard v1.1
hwreverse/PokeConSound
Soundcard Designs for Pocket Computers (ポケコン) (Sharp, Casio, TRS80-M100,...)
22 parts7MIT - 2 layers60 × 100 mm

- 2 layers72.6 × 24.9 mm

Huesful power adaptor
Hypfer/huesful-power-adaptor
Use proper PSUs with Hue Signes, Playbars and more
8 parts7CC-BY-SA-4.0 - 2 layers121.9 × 129 mm

Name unneeded
ibnuda/name-unneeded
Name Unneeded 36 keys, your basic minidox-look-alike. 38 keys, your basic minidox-look-alike plus 2 more thumb keys.
66 parts7GPL-3.0 - 2 layers111.4 × 40.9 mm

Rainworks Electrical
IceyPlazza/EWB-EPA-Rainworks
26-27 EWB EPA Rainworks project; We're putting a sensor box in the ground!
29 parts7 - 2 layers63.5 × 56.6 mm

- 2 layers

Headphone amp
ildus/pangaea_cp16
Guitar cabinet simulator (on impulse responses) based on AMT Pangaea CP-16
77 parts7 - 2 layers249.2 × 109.8 mm

Ebbe34
indianpojken/ebbe34
Wireless 34-key unibody keyboard w/ hotswappable choc v1 & v2 switches
90 parts7 - 2 layers88.9 × 59.7 mm

FloppyRider
inmbolmie/FloppyRider
Full-featured DIY PC-compatible 8-inch Diskette drive based on the IBM 51TD.
32 parts7GPL-3.0 - 4 layers100 × 40.1 mm

- 2 layers70 × 40 mm

Scale ltc6915
IoTReady/low-power-nrf52-weighing-scale
https://iotready.co/low-power-nrf52-weighing-scale/
76 parts7 - 2 layers50 × 35 mm

- 2 layers124.7 × 140.5 mm

CANSAT PAYLOAD MK3B
its-villada/mCALCAN
Satélite CANSAT del instituto técnico salesiano Villada.
61 parts7GPL-3.0 - 2 layers59.7 × 41.9 mm

Vs1053-waveblaster se
ivop/vs1053-waveblaster
New WaveBlaster Daughterboard based on the VS1053 chip
43 parts7 - 4 layers26 × 25.6 mm

Framework usb2can
JackToaster/framework-usb2can
USB to CAN device in a Framework laptop expansion card
39 parts7 - 4 layers66 × 36 mm

Gas sensor
JamesTwallin/gas_sensor
A tiny plug-in board for the rev E phone-companion board. It stands upright in a notch in rev E's sensor end, between the two gas sensor cans, and pokes 4.5 mm out through a slot in the case face, so its tip sits in the…
81 parts7MIT - 2 layers36 × 33.5 mm

- 2 layers30.7 × 17.6 mm

OtterPill CAN
Jana-Marie/OtterPill-CAN-Adapter
CAN-adapter for the OtterPill running candleLight firmware.
10 parts7 - 2 layers110 × 83.7 mm

RAMPS STM32F407 TFT Touch
Jarins/STM32F407-RAMPS
RAMPS for STM32F407ZE_ZG Dev. Board Black edition
104 parts7GPL-3.0 - 2 layers128 × 25.4 mm

A500 86pin internal adapter
jbilander/A500_Edge_Expansion_adapter
A500 86pin edge connector adapter. Turns the expansion edge into a 86pin female socket inside the A500 case.
3 parts7CC-BY-SA-4.0