Skip to the content

Boards using the TLV9062IDR-MS

16 boards

Boards in 14 GitHub repositories, designed in KiCad, that use the TLV9062IDR-MS by MSKSEMI (-2.75V~-1.1V、1.1V~2.75V -40℃~+85℃ 10V/us 11MHz 2 2.2V~5.5V 20mA 300uA 30pA 400pA 600nV/℃ 60nV/√Hz@1kHz 800uV 95dB Rail-to-Rail Input, Rail-to-Rail Output SOP-8 Operational Amplifier ROHS). See how each wires it, with its parts, size, README and files; the TLV9062IDR-MS’s symbol, footprint and pinout are on its own page.

  • 2 layers73 × 99.8 mmSodium, the printed circuit board in 3D

    Sodium

    kanengomibako/Sodium

    85 parts14Unlicense
  • 2 layers60 × 60 mmScbs pico, the printed circuit board in 3D

    Scbs pico

    CoolNamesAllTaken/scbs

    Single Cell Battery Simulator for testing a BMS.

    64 parts4
  • 4 layers116 × 112 mmBldc esc, the printed circuit board in 3D

    Bldc esc

    EwoudVV/bldc-esc

    A custom STM32 motor controller for BLDC and PMSM motors.

    453 parts2
  • 4 layers90 × 60 mmBench psu, the printed circuit board in 3D

    Bench psu

    PaulBichl/VibePCB-bench-psu

    USB-C PD (20 V) powered bench supply, 2 independent channels, 1.6-16.6 V / 3 A each, constant voltage / constant current, designed with VibePCB.

    206 parts1
  • 2 layers71 × 46.4 mmProbe, the printed circuit board in 3D

    Probe

    0xDBFB7/psychic-probe

    A dirt-cheap high-sample-rate multi-channel datalogger.

    104 parts
  • 4 layers54.8 × 83.5 mmE nez, the printed circuit board in 3D

    E nez

    gberthou/e-nez

    Data acquisition platform | e-nez

    108 partsMIT
  • 4 layers67 × 140.3 mmUnkey, the printed circuit board in 3D

    Unkey

    natecermak/unkey

    Swimmie-Textie

    139 parts
  • 6 layers98 × 64 mmLa ecp5, the printed circuit board in 3D

    La ecp5

    PaulBichl/VibePCB-LA

    A 16-channel, 100 MSa/s USB 2.0 HS logic analyzer: a Lattice ECP5 FPGA (CABGA-256 BGA) capturing into a 32 MB SDRAM (54-ball BGA), read out over an FT2232H. 98 x 64 mm, 6 layers.

    103 parts
  • 2 layers60 × 60 mmScbs stm32g4, the printed circuit board in 3D

    Scbs stm32g4

    CoolNamesAllTaken/scbs

    Single Cell Battery Simulator for testing a BMS.

    64 parts4
  • 4 layers65 × 42 mmCrowsync recorder, the printed circuit board in 3D

    Crowsync recorder

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    55 parts3MIT
  • 4 layers85 × 78 mmPod, the printed circuit board in 3D

    Pod

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    35 parts3MIT
  • 2 layers41 × 36.5 mmCarradio audio rev07, the printed circuit board in 3D

    Carradio audio rev07

    gschuurman/android_vendor_gschuurman_vehicle_interfaces

    vehicle interfaces for android automotive for a custom headunit

    70 parts
  • 4 layers25 × 50 mmBalancerREF OptHead, the printed circuit board in 3D

    BalancerREF OptHead

    natehorst240-sketch/HoboBalancer

    Hobby helicopter rotor-balancing instrumentation. KiCad 10 projects plus ESP32-S3 firmware.

    31 parts
  • 2 layers100 × 100 mmAquaPCB, the printed circuit board in 3D

    AquaPCB

    schwabix-1311/aquaPCB

    Open-hardware Raspberry Pi base board for aquaPi software. 12 V supply; six 5 A MOSFET outputs for LED lamps and fans (2 with hardware PWM); 4 SSR/relay drivers; protected inputs; 1-Wire; ADS1115 with a pH amplifier on…

    147 partsCERN-OHL-S-2.0
  • 4 layers60 × 60 mmCrown, the printed circuit board in 3D

    Crown

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    95 parts