
PCB design
1,387 boardsKiCad boards from 598 GitHub repositories tagged “pcb-design”, the most starred first; open any of them in PCBKit.
- 2 layers26 × 26 mm

- 2 layers74.2 × 79 mm

Kitchen timer
krystofh/kitchen_timer
TimeUp kitchen timer based on 4-digit segment display, Raspberry Pi Pico and running on Zephyr RTOS
39 partsApache-2.0 - 4 layers60 × 30 mm

BinaryClock3
kwame-y/BinaryClock
A rechargeable pocket clock displaying HH:MM:SS with 20 LEDs, built around an ATtiny1616, a constant-current LED driver, and a real-time clock.
58 parts - 4 layers78 × 49 mm

'atmega328p blink board
kyvrit05/KiCad-Model-1-ATmega328P-Blink-Board
A simple PCB design - Project 1
15 parts - 2 layers156 × 128 mm

Hybridimager v2-als pt19-32x32
lachlanchen/HybridImager
HybridImager: open hybrid single-pixel, event, frame, and spectral scientific imaging research workspace
1,033 parts - 2 layers100 × 80 mm

G474 Integrated Analyzer
Larryhul/periodic-signal-analyzer
STM32G474 periodic signal analyzer: FFT harmonic measurement (Upp/Urms/fundamental/spectrum), OPA2365 front end, KiCad PCB, firmware & dashboard. 2026 Shanghai electronic design contest, Problem G. 周期信号测量分析装置
64 partsMIT - 2 layers78 × 99.5 mm

Precision AFE ESP32
LemonAidLee/Precision-Analog-Front-End
A highly precise, ±100 mV analog front-end (AFE) designed for the ESP32 and ADS1115. Features a 4-stage TL082 architecture including a Sallen-Key low-pass filter, delivering 9.4 µV/LSB resolution for precision data…
29 partsCERN-OHL-P-2.0 - 4 layers55.9 × 78.7 mm

ESP32 BUCK WLED NO BOARD
lepetidozo/wledController_V1
I wanted to make a custom WLED controller for my bedroom's ledstrip and to learn more about electronics and PCB design
40 parts - 2 layers70 × 60 mm

- 4 layers66 × 58.5 mm

FOC Driver
Loredati-svg/BLDC-FOC-Motor-Driver
Single-motor BLDC/PMSM FOC driver: STM32G431 + DRV8323RH, 4-layer round PCB with on-board MA730 magnetic encoder. Motor block for a self-balancing robot. Designed in KiCad 10.
96 parts - 4 layers78.9 × 51 mm

ClockClock24
Loredati-svg/ClockClock24
ClockClock 24 replica: 24 analog clocks showing digital time. ESP32-S3 controllers with VID6606 stepper drivers, auto-addressed I2C bus and VID28-05 dual-shaft motors. KiCad 10.
46 parts - 2 layers100 × 100 mm

Tach v1.0
maheen-ahmed1/OptoTACH
Precision non-contact optical tachometer (0–9999 RPM/RPS) built entirely with discrete CMOS logic & 555 timers; no microcontroller, no firmware. Includes KiCad EDA, 3D model, Python simulation, and bench validation.
99 parts - 4 layers60 × 120 mm

Theoros
Majorwhiskey/gps-lora
Theoros is a USB-C GPS logger and LoRa tracker built on the ESP32-S3. It logs 1 Hz u-blox M10 fixes to microSD, shows status on an OLED and sends AES-128-CCM encrypted position over 868 MHz LoRa.
88 partsCERN-OHL-P-2.0 - 2 layers93 × 48 mm

Keypadplz
MakerJake01/ProMicro_MacroPad
This is all the files needed to build an 8 key ProMicro based MacroPad.
51 parts - 2 layers86 × 67 mm

- 2 layers46.5 × 19.6 mm

Arduino nano custom board
marwantm/arduino-nano-custom-board
Custom 2-layer Arduino Nano clone built around the ATmega328P.
37 parts - 4 layers99.6 × 55.8 mm

Esp32-sensor board
marwantm/esp32-sensor-board
ESP32-C3 IoT sensor node with USB-C power path management — KiCad PCB design project
86 parts - 4 layers54.2 × 28.1 mm

STM32-Bluetooth
marwantm/STM32-Bluetooth
STM32WB55 Bluetooth development board — KiCad PCB design project
48 parts - 2 layers60 × 34 mm

- 2 layers38 × 47 mm

Krabbler
maxikuehn/AMR_Krabbler
University Project, combining robotics, 3d-Printing and PCB-design.
20 partsMIT - 4 layers

Lora node
Mehdi-Ldj/lora-ble-sensor-node
Off-grid LoRa/BLE sensor node — 868 MHz LoRa, 2.4 GHz BLE, solar/LiFePO4
110 partsCERN-OHL-P-2.0 - 4 layers73 × 33 mm

CAN485-dongle
Mehdi-Ldj/usb-can-rs485-dongle
CAN-485 diagnostic gateway — rev A hardware
77 partsCERN-OHL-P-2.0 - 2 layers33 × 37 mm

Single Sided-5V Power Supply
Mimo-Mir/Single-Sided-5V-Power-Supply
PCB design project using KiCad 9: single-sided 5V regulated power supply with LM7805, full design workflow from schematic to Gerber files.
8 partsMIT - 2 layers96.5 × 63.5 mm

Led zeppelin board
MiroKeimioniemi/digital-fabrication-portfolio
My Digital Fabrication Portfolio created for the 2024 Digital Fabrication Fab Academy overlay course at Aalto Fablab, containing extensive documentation for 6 months worth of hands-on learning in designing and…
32 parts