2 layers98.9 × 78 mm
Siot gateway particle io
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
28 parts9Apache-2.0
2 layers21.8 × 20.8 mm
Siot node current clamp
simpleiot/hardware9Hardware designs for IoT devices and sensor nodes.
- Size
- 21.8 × 20.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 9
- Nets
- 8
- Pads
- 30
- Tracks, vias
- 54, 15
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 21 Sep 2019
- Updated
- 4 Mar 2021
Overview
Siot node current clamp is an open-source printed circuit board by simpleiot, from the simpleiot/hardware repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 21.8 × 20.8 mm with 9 parts on 8 nets, routed with 54 tracks and 15 vias.
It is built around the ADP7142AUJZ-5.0-R7 and DS2438Z+. Its parts include 3 capacitors, 3 connectors, 2 ICs and 1 resistor. It belongs with the home automation and IoT boards of this library.
Main components
2
ADP7142AUJZ-5.0-R7
TSOT-23-5-40℃~+125℃@(Ta) 1 11uVrms 200mA 40V 5V 88dB@(10kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAnalog DevicesVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
DS2438Z+
SOIC-8-40℃~+85℃ 1~2 2.4V~10V SOIC-8 Battery Management ROHSMaxim Integrated (Analog Devices)Battery Management
README
rpi-odroid-expansion/README.mdrPI/Odroid Exansion Board
Features
This board is designed to provide a number of expansion features to Raspberry PI and ODROID-C4 SBCs.
- CAN
- RS485
- 1-wire
- LCD/Touchscreen
- pass through rPI expansion connector to provide use of unused pins.
- XBee socket (Digi, Nimbelink, etc radios)
- reference design: https://nimbelink.com/products/raspberry-pi-skywire-adapter/
- supports both standard 40-pin expansion and compute module
- LoraWan radio
MPU Interface
MPU/MCU communication link
There is a UART and SPI ports (todo) wired between the host MPU and the MCU on the expansion board.
- UART is likely simplest as the existing CAN firmware implements a USB serial port. Also, for RS485, it is just a pass through.
- SPI would allow us to run both CAN and RS485 at the same time.
- may only be two hardware SPI chip selects, so not sure how well more than 2 SPI devices will work.
MCU Implementation
A STM32F042K4Tx MCU is used to implement the following functionality:
- CAN Interface
- Board ID EEPROM (implements i2c slave)
Reference
CAN
Can is typically implemented using a SPI CAN controller (ex MCP2517), but these devices do not offer any buffering so are a poor choice for non real-time operating systems like Linux. Thus, we've chosen to use a MCU to provide the CAN interface and hopefully leverage firmware from the following projects:
HAT ID EEPROM
RS485
Parts
9| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 2.2uF_50V | Capacitor_SMD:C_0603_1608Metric | C2, C3 |
| 2 | xConnect_smd | BEC:xConnect_smd | J1, J3 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | ADP7142AUJZ-5.0 | Package_TO_SOT_SMD:TSOT-23-5 | U1 |
| 1 | Conn_01x02_Female | BEC:1x03_solder-pads | J2 |
| 1 | DS2438 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
Questions
How big is the Siot node current clamp PCB?
It measures 21.8 × 20.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Siot node current clamp use?
9 parts, built around the ADP7142AUJZ-5.0-R7 and DS2438Z+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Siot node current clamp KiCad files?
From the simpleiot/hardware repository on GitHub, at the commit this page was made from: the board is siot-node-current-clamp/siot-node-current-clamp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Siot node current clamp design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from simpleiot/hardware
7- 2 layers100 × 45.5 mm
Siot gateway particle
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
25 parts9Apache-2.0 - 2 layers65 × 56.5 mm
Rpi odroid expansion
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
14 parts9Apache-2.0 - 2 layers37.2 × 46.6 mm
Siot node relay
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
12 parts9Apache-2.0 - 2 layers21.6 × 21.6 mm
Siot node temp
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
9 parts9Apache-2.0 - 2 layers
Siot node temp humidity rj11
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
5 parts9Apache-2.0 - 2 layers37.3 × 46.6 mm
Siot splice kit
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
4 parts9Apache-2.0
Similar boards
- 2 layers56.3 × 118.2 mm
Robot
jhud/robot_board
Controller board for building servo-based robots, such as hexapods.
90 parts1GPL-3.0 - 2 layers
- 2 layers160 × 120 mm
- 2 layers88.6 × 69.9 mm
ExpressionController
amonbenson/expad
A four-jack USB MIDI adapter for expression and sustain pedals, built on a Raspberry Pi Pico 2 W. It works out what is plugged into each jack - whichever contact a pedal's wiper is on, and whether it is a potentiometer…
147 partsMIT - 4 layers300 × 270 mm
- 2 layers78 × 62.5 mm
Scr23-sens to can
m888r/scr23-analog-to-can
USC Racing 2023 FSAE Car Analog/Digital to CAN module
62 parts - 4 layers99.9 × 99.9 mm
Signal generator
Pejo-306/digital-function-generator-v2
Цифров генератор на сигнали с тъчскрийн
157 partsMIT - 4 layers84.8 × 84.3 mm
Beuty
HrishikeshMRao/Electronics_Hardware_Projects
Find my simulation files and PCB_Designs here
58 parts2