

Mini MK1
Building custom flight computers
- Size
- 25 × 80 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 135
- Nets
- 159
- Pads
- 648
- Tracks, vias
- 697, 353
- Pours
- 15
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 14 Oct 2020
- Updated
- 7 Nov 2026
Overview
Mini MK1 is an open-source printed circuit board by ISSUIUC, from the ISSUIUC/ISS-PCB repository on GitHub. It is a 4-layer board of 25 × 80 mm with 135 parts on 159 nets, routed with 697 tracks and 353 vias.
It is built around the E22-400MM22S, ESP32-S3-MINI-1U-N8 and SAM-M10Q-00B, with the MMC5983MA, MS5611-01BA03 and ZDSD64GLGEAG-R among its other parts. Its parts include 55 resistors, 27 capacitors, 16 ICs, 10 diodes and 10 connectors. It belongs with the sensors and measurement boards and the ESP32 and NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
12E22-400MM22S
SMD,10x10mm-147dBm 1.8V~3.7V 100mA 22.3dBm 433MHz、470MHz 6.5mA 7km Continuous frequency coverage LoRa SPI Stamp Hole Antenna、IPEX interface SMD,10x10mm LoRa Modules ROHSChengdu Ebyte Elec TechLoRa ModulesESP32-S3-MINI-1U-N8
VFQFN-56-EP-40℃~+105℃ -98.4dBm 1.8V~3.6V、3V~3.6V 2.4GHz 21dBm 340mA 88mA Bluetooth5.0 ESP32-S3 UART、SDIO、SPI、I2C、I2S、JTAG、USB VFQFN-56-EP WiFi Modules ROHSEspressif SystemsWiFi ModulesSAM-M10Q-00B
LGA-20Hot start acceleration LGA-20 GNSS Modules ROHSu-bloxGNSS ModulesMMC5983MA
LGA-16(3x3)-40℃~+105℃ 18bit 2.8V~3.6V 450uA I2C、SPI ±8Gs ±8Gs LGA-16(3x3) 3D Magnetic Sensors ROHSMEMSIC3D Magnetic SensorsMS5611-01BA03
QFN-8(3x5)QFN-8(3x5) Pressure Sensors ROHSMEASPressure SensorsZDSD64GLGEAG-R
LGA-8(6.2x8)-25℃~+85℃ 2.7V~3.6V 200uA 50MHz 64Gbit ECC error correction function、Bad block management function SPI、SD interface Yes LGA-8(6.2x8) NAND FLASH ROHSZettaNAND FLASHTVS1800DRV
WSON-6(2x2)-40℃~+125℃ 116pF 18V 21.3V 22.8V 40A@8/20us 500pA 960W@8/20us IEC 61000-4-2、IEC 61000-4-5 TVS Unidirectional WSON-6(2x2) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsSurge Protection Devices (SPDs)ECMF02-2AMX6
UFQFN-6(1.5x1.7)-40℃~+85℃ 2 2.5Ω 200mA UFQFN-6(1.5x1.7) Common Mode Filters ROHSSTMicroelectronicsCommon Mode FiltersLSM6DSV320X
LGA-14L(2.5x3)-40℃~+85℃ 1.71V~3.6V 2.9uA 4.5KB IMU (accelerometer + gyroscope) Motion event detection、Synchronization and timestamp SPI、I2C X,Y,Z X,Y,Z ±320g ±4000dps LGA-14L(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometersTCA4307DGK
MSOP-8-40℃~+125℃ 10ns 2-Wire Bus 2-Wire Bus 2.3V~5.5V 400Kbps 5pF Buffer Bus capacitance isolation、Hot-swap protection、Power-off isolation MSOP-8 Signal Buffers, Repeaters, Splitters ROHSTexas InstrumentsSignal Buffers, Repeaters, SplittersTCAL9538PW
TSSOP-16TSSOP-16 I/O Expanders ROHSTexas InstrumentsI/O ExpandersSDM05U40CSP
X3-WLB1006-2-55℃~+150℃ 14A 40V 415mV@500mA 500mA 75uA@40V Independent X3-WLB1006-2 Schottky Diodes ROHSDiodes IncorporatedSchottky Diodes
README
boards/Feather_Duo/README.mdFeather Duo
The Feather Duo radio receiver was conceived to optimize communication with MIDAS and simplify the team’s ground station setup, including two LoRa radios for concurrent reception from both stages and software support for increased data rates. It succeeds the Adafruit Feather M0 RFM96 as the team’s primary ground station receiver.
Read more about the Feather Duo, MIDAS and the surrounding avionics systems in the MIDAS MK2 Report.
Schematics
Printable PDF schematics and layouts for the Feather Duo can be found in the PDFs and images folders.
Photos
Parts
135| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100k | Resistor_SMD:R_0402_1005Metric | R101, R103, R104, R105, R108, R109, R116, R404, R407, R408, R414, R419, R420 |
| 13 | 100nF | Capacitor_SMD:C_0402_1005Metric | C105, C106, C107, C108, C109, C113, C114, C301, C302, C304, C305, C306, C403 |
| 7 | TestPoint_Small | TestPoint:TestPoint_Pad_D1.0mm | TP101, TP102, TP103, TP104, TP105, TP106, TP107 |
| 6 | 1uF | Capacitor_SMD:C_0402_1005Metric | C101, C102, C103, C112, C201, C202 |
| 5 | 1k | Resistor_SMD:R_0402_1005Metric | R405, R406, R412, R417, R418 |
| 5 | 470 | Resistor_SMD:R_0402_1005Metric | R121, R122, R123, R124, R207 |
| 5 | 50k | Resistor_SMD:R_0402_1005Metric | R110, R111, R112, R113, R114 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric | R115, R119, R423, R424 |
| 4 | 18k | Resistor_SMD:R_0402_1005Metric | R409, R410, R421, R422 |
| 4 | 3.3k | Resistor_SMD:R_0402_1005Metric | R401, R402, R415, R416 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H101, H102, H103, H104 |
| 2 | 10uF | Capacitor_SMD:C_0402_1005Metric | C110, C303 |
| 2 | 150k | Resistor_SMD:R_0402_1005Metric | R403, R413 |
| 2 | 16.9k | Resistor_SMD:R_0402_1005Metric | R201, R203 |
| 2 | 4.7k | Resistor_SMD:R_0402_1005Metric | R117, R118 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C204, C402 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R106, R107 |
| 2 | 5k | Resistor_SMD:R_0402_1005Metric | R202, R204 |
| 2 | ESD321 | Package_SON:Texas_DPY0002A_0.6x1mm_P0.65mm | D102, D103 |
| 2 | RED LED | LED_SMD:LED_0603_1608Metric | D104, D203 |
| 2 | SDM05U40CSP | Diode_SMD:D_SOD-882 | D101, D202 |
| 2 | Screw_Terminal_01x06 | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-6_1x06_P2.54mm_Horizontal | J102, J103 |
| 2 | Si7232DN | Transistor_FET_Vishay:Vishay_PowerPAK_1212-8_Dual | Q401, Q402 |
| 2 | TVS1800DRV | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U201, U202 |
| 1 | 100mF | Capacitor_SMD:CP_Elec_10x10.5 | C203 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C111 |
| 1 | 20 | Resistor_SMD:R_0612_1632Metric | R206 |
| 1 | 20k | Resistor_SMD:R_0402_1005Metric | R120 |
| 1 | 21.5k | Resistor_SMD:R_0402_1005Metric | R205 |
| 1 | 22uF | Capacitor_SMD:C_0402_1005Metric | C104 |
| 1 | 330nH | Inductor_SMD:L_0402_1005Metric | L101 |
| 1 | 4.7nF | Capacitor_SMD:C_0402_1005Metric | C401 |
| 1 | 560k | Resistor_SMD:R_0402_1005Metric | R102 |
| 1 | 820 | Resistor_SMD:R_0402_1005Metric | R411 |
| 1 | ADS7138-Q1 | Package_DFN_QFN:WQFN-16-1EP_3x3mm_P0.5mm_EP1.68x1.68mm | U101 |
| 1 | BAS116L | Diode_SMD:D_SOD-882 | D201 |
| 1 | BLUE LED | LED_SMD:LED_0603_1608Metric | D107 |
| 1 | Buzzer | Buzzer:Buzzer_SMTB-0927-TW-R | BZ101 |
| 1 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J202 |
| 1 | Conn_01x02 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | J107 |
| 1 | Conn_01x03 | Connector_Molex_Micro-Lock-Plus:Molex_Micro-Lock_2200980371_1x03_P1.25mm_Horizontal | J104 |
| 1 | Conn_01x03 | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J106 |
| 1 | Conn_01x03 | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J108 |
| 1 | E22-400MM22S | RF_Module_Ebyte:E22-400MM22S | U106 |
| 1 | ECMF02-2AMX6 | Package_DFN_QFN:ST_UQFN-6L_1.5x1.7mm_P0.5mm | U102 |
| 1 | ESP32-S3-MINI-1U | RF_Module:ESP32-S2-MINI-1U | U103 |
| 1 | GREEN LED | LED_SMD:LED_0603_1608Metric | D106 |
| 1 | LOGO | memes:Grainger_smaller | G*** |
| 1 | LOGO | Logos_ISS:ISS_LOGOV2_tiny | G*** |
| 1 | LSM6DSV320X | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U302 |
| 1 | MMC5983MA | Package_LGA:LGA-16_3x3mm_P0.5mm | U301 |
| 1 | MS5611-01BA | Package_LGA:LGA-8_3x5mm_P1.25mm | U303 |
| 1 | ORANGE LED | LED_SMD:LED_0603_1608Metric | D105 |
| 1 | SAM-M10Q | RF_GPS:ublox_SAM-M8Q | U107 |
| 1 | SMA | Connector_Coaxial:SMA_Molex_73251-2120_EdgeMount_Horizontal | J105 |
| 1 | TCA4307 | Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.45x2.4mm | U105 |
| 1 | TCAL9538 | Package_DFN_QFN:UQFN-16_1.8x2.6mm_P0.4mm | U402 |
| 1 | TPS2121 | Package_DFN_QFN:Texas_VQFN-HR-12_2x2.5mm_P0.5mm | U203 |
| 1 | TPS25947 | Package_VQFN:VQFN-HR-RPW0010A | U401 |
| 1 | TPS746-Q1 | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U204 |
| 1 | TestPoint | TestPoint:TestPoint_THTPad_1.5x1.5mm_Drill0.7mm | J201 |
| 1 | USB4105-GF-A | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J101 |
| 1 | ZDSD64GLGEAG-R | Package_LGA:LGA-8_8x6.2mm_P1.27mm | U104 |
More from ISSUIUC/ISS-PCB
12- 4 layers60 × 100 mm

- 4 layers60 × 100 mm

- 4 layers45 × 100 mm

- 4 layers45 × 100 mm

- 4 layers70 × 70 mm

- 4 layers70 × 70 mm

- 4 layers40 × 60 mm

- 2 layers40 × 60 mm

- 4 layers40 × 40 mm

- 4 layers62 × 82 mm
/GATOR.kicad_pcb.jpg?size=s&soon)
- 2 layers100 × 80 mm

- 4 layers50 × 55 mm

Similar boards
- 4 layers48.4 × 61.4 mm

Flight computer
Terrapin-Rocket-Team/SRAD-Avionics
Code and PCBs for the avionics subteam for the SRAD flight computer and side projects
101 parts17 - 6 layers31.1 × 10.9 mm

Emg afe module
Genabl/parasitic_monorepo
Second-board regression target for the volume-conductor pipeline.
39 partsMIT - 6 layers30 × 60 mm

Flight Computer
Pioneer-Rocketry/Flight-Computer
Pioneer Rocketry’s latest generation flight computer for high power, STM32-based avionics system designed for experimental high-power rockets.
116 parts2 - 4 layers102.8 × 88.4 mm

- 4 layers85 × 65 mm

Power Board
AdvikChitre/MSL_Imperial_2023
Repository for Imperial College London Robocup MSL team 2023
175 parts2 - 4 layers16 × 39 mm

- 4 layers40 × 75 mm

CUR flight computer 25-26
CU-Rocketry/flight_computer
Competition Flight Computer Module 25-26
169 parts1 - 4 layers26 × 28 mm

Questions
How big is the Mini MK1 PCB?
It measures 25 × 80 mm and has 4 copper layers, 1.61 mm thick.
What parts does the Mini MK1 use?
135 parts, built around the E22-400MM22S, ESP32-S3-MINI-1U-N8, SAM-M10Q-00B and MMC5983MA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Mini MK1 KiCad files?
From the ISSUIUC/ISS-PCB repository on GitHub, at the commit this page was made from: the board is boards/Mini-MK1/Mini-MK1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Mini MK1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask ISSUIUC before reusing the design.