Skip to the content

MMC5983MA

MEMSICExtended

-40℃~+105℃ 18bit 2.8V~3.6V 450uA I2C、SPI ±8Gs ±8Gs LGA-16(3x3) 3D Magnetic Sensors ROHS

Part id
memsic/MMC5983MA
Category
3D Magnetic Sensors
Package
LGA-16(3x3)
Pins
16
In stock
6,736 at JLCPCB (C404329)
Used on
95 open-source boards

Overview

The MMC5983MA is a 3D Magnetic Sensor made by MEMSIC in a LGA-16(3x3) package with 16 pins. -40℃~+105℃ 18bit 2.8V~3.6V 450uA I2C、SPI ±8Gs ±8Gs LGA-16(3x3) 3D Magnetic Sensors ROHS.

PCBKit's library has its KiCad symbol (Sensors:MMC5983MA, from CERN's library) and its footprint (ICs And Semiconductors SMD:PQFN50P300X300X100-16N_a, from CERN's library), ready for a KiCad board. 6,736 are in stock at JLCPCB (part C404329). 95 open-source boards in 73 repositories on GitHub use it.

Symbol

1SCL/SPI_SCK16SDA/SPI_SDI5SPI_SDO4PSI_CS15INT13VDDIO2VDD3NC6NC7NC8NC12NC14NC10CAP9GND11GND
Sensors:MMC5983MAFrom CERN's library

Footprint

ICs And Semiconductors SMD:PQFN50P300X300X100-16N_aFrom CERN's library

From the datasheet

7
Supply, least
2.8 V · VDD, recommended operating min · p. 2
Supply, most
3.6 V · VDD, recommended operating max · p. 2
Supply, absolute maximum
3.6 V · Supply Voltage, absolute max · p. 9
Works from
-40 °C · Operating Temperature min · p. 2
Works up to
105 °C · Operating Temperature max · p. 2
Takes working
450 µA · Supply Current typical, BW=00, 7 measurements/second, VDD=3.0V · p. 2
Takes asleep
1 µA · Power Down Current typical · p. 2

What it is and has

14
Sensor axes
3 · p. 1
Magnetic field range
±8 G · p. 1
Resolution
18 bits · p. 1
Total RMS noise
0.4 mG · p. 1
Maximum output data rate
1000 Hz · p. 1
Package dimensions
3.0mm x 3.0mm x 1.0mm · p. 1
Degaussing
Built-in SET/RESET function · p. 1
Sensitivity compensation
On-chip · p. 1
Temperature sensor
On-chip · p. 1
Interrupt
Data_Ready · p. 1
I2C
Slave, FAST mode, ≤400 KHz · p. 1
SPI
Available · p. 1
Compliance
RoHS · p. 1
Qualification
AEC-Q100 · p. 1

Around it

3
cap 10 uF
between CAP and GND; Minimum capacitance; low ESR; place close to CAP for the SET/RESET coil. · p. 11
res 2.7K ohm
between SDA and VDD; I2C pull-up for bus length less than 10 cm. · p. 12
res 10K ohm
between SDA and VDD; I2C pull-up for bus length less than 5 cm. · p. 12

Specifications

42
ParameterConditionsAs printedPage
Field Range (Each Axis)Total applied field; measurements @ 25C, VDD=3.0Vtyp 8 G2
Supply VoltageVDDmin 2.8 · typ 3 · max 3.6 V2
Supply VoltageVDDIO(I2Cinterface and INT)min 2.8 · typ 3 · max 3.6 V2
Supply Voltage Rise Timemax 5 ms2
Supply CurrentBW=00; 7 measurements/second; VDD=3.0V; 25Ctyp 450 uA2
Supply CurrentBW=01; 7 measurements/second; VDD=3.0V; 25Ctyp 225 uA2
Supply CurrentBW=10; 7 measurements/second; VDD=3.0V; 25Ctyp 112.5 uA2
Supply CurrentBW=11; 7 measurements/second; VDD=3.0V; 25Ctyp 32 uA2
Power Down CurrentVDD=3.0V; 25Ctyp 1 uA2
Operating Temperaturemin -40 · max 105 C2
Storage Temperaturemin -55 · max 125 C2
Linearity Error (Best fit straight line)FS=±8G; Happlied=±4Gtyp 0.1 %FS2
Hysteresis3 sweeps across ±8Gtyp 0.01 %FS2
Repeatability Error3 sweeps across ±8Gtyp 0.1 %FS2
Alignment Errortyp 1 · max 3 Degrees2
Transverse Sensitivitytyp 0.8 %2
Total RMS NoiseBW=00typ 0.4 mG2
Total RMS NoiseBW=01typ 0.6 mG2
Total RMS NoiseBW=10typ 0.8 mG2
Total RMS NoiseBW=11typ 1.2 mG2
Output Resolutiontyp 18 Bits2
Max Output data rateBW=00typ 50 Hz2
Max Output data rateBW=01typ 100 Hz2
Max Output data rateBW=10typ 225 Hz2
Max Output data rateBW=11typ 580 Hz2
Max Output data rateBW=11(CM_Freq=111)typ 1000 Hz2
Heading AccuracyUsing MEMSIC’s proprietary software or algorithmtyp 1 Degrees2
Sensitivity Accuracy8 Gtyp 5 %2
Sensitivity AccuracyWith16bits operationtyp 4096 Counts/G2
Sensitivity AccuracyWith18bits operationtyp 16384 Counts/G2
Sensitivity Change Over Temperature-40~105 C; Delta from 25 C, 8 Gtyp 5 %2
Null Field Outputtyp 0.5 G2
Null Field OutputWith16bits operationtyp 32768 Counts2
Null Field OutputWith18bits operationtyp 131072 Counts2
Null Field Output Change Over Temperature using SET/RESET-40~105 C; Delta from 25 Ctyp 3 mG2
Temperature Sensor Outputtyp 0.8 C/Count2
Disturbing FieldExternal field tolerated without changing sensor characteristics; SET/RESET required if exceededtyp 10 G2
Maximum Exposed Fieldmax 10000 G2
SET/RESET Repeatabilitytyp 1 mG2
Supply Voltagemin -0.5 · max 3.6 V9
Storage Temperaturemin -55 · max 125 C9
Maximum Exposed Fieldmax 10000 G9

Pins, by the datasheet

16
1 SCL/SPI_SCK
Serial clock line for I2C/SPI bus. · p. 9
2 VDD
Power supply; internally shorted to CAP. · p. 11
3 NC
Not Connected. · p. 9
4 SPI_CS
Active-low SPI chip select; tie to VDDIO for I²C interface. · p. 9
5 SPI_SDO
SPI serial data out. · p. 9
6 NC
Not Connected. · p. 9
7 NC
Not Connected. · p. 9
8 NC
Not Connected. · p. 9
9 GND
Connect to Ground. · p. 9
10 CAP
Supply input for SET/RESET coil; connect a minimum 10 uF low ESR capacitor close to the pin; internally shorted to VDD. · p. 11
11 GND
Connect to Ground. · p. 9
12 NC
Not Connected. · p. 9
13 VDDIO
Power supply for I2C and INT. · p. 9
14 NC
Not Connected. · p. 9
15 INT
Active-high interrupt output; held as hi-Z until an interrupt function is enabled. · p. 11
16 SDA/SPI_SDI
Serial data line for I2C/SPI bus. · p. 9

Ordering codes, by the datasheet

1
MMC5983MA
LGA16 · Industrial Grade; RoHS compliant; tape and reel, 5000pcs per 13” reel; 7-bit I2C address 0110000. · p. 9

Open-source boards using it

95See all 95
  • 4 layers33 × 90 mmActive drag system, the printed circuit board in 3D

    Active drag system

    RocketryVT/active-drag-system

    Eigen Library, cmake, and arm-none-eabi-gcc tooling required for successful build.

    100 parts6MIT
  • 4 layers70.8 × 100 mmFlapjack, the printed circuit board in 3D

    Flapjack

    Caleb646/Flapjack

    A custom VTOL drone platform — from airframe to PCB to firmware.

    116 parts4
  • 4 layers47 × 21.6 mmRotini Hardware, the printed circuit board in 3D

    Rotini Hardware

    AlfredoSystems/Rotini-Hardware

    📖 Documentation: https://www.alfredosys.com/Rotini-Hardware/ (pinout, power limits, flashing ExpressLRS, first Arduino upload)

    116 parts3MIT
  • 4 layers31 × 100 mmKp ptr, the printed circuit board in 3D

    Kp ptr

    PTR-projects/PTR_mega_hardware

    Welcome to the KPPTR-hardware repository! This repository contains the design files for the hardware components used in the KPPTR project.

    208 parts3MIT
  • 2 layers120 × 80 mmMainBoard v1, the printed circuit board in 3D

    MainBoard v1

    shimotoriharuki/2021RoboTrace_Kicad

    This repository contains circuit data for line-following robot (UnderBird).

    166 parts3GPL-3.0
  • 6 layers90 × 45 mmHw tele stern, the printed circuit board in 3D

    Hw tele stern

    shorlee/TeleSTERN

    The TeleSTERN Project is an Open Source Rocketry Flight Computer based on the TeleMega by Altus Metrum.

    303 parts3GPL-3.0
  • 4 layers50 × 100 mmStDevboard, the printed circuit board in 3D

    StDevboard

    teletype7/IRIS

    166 parts3MIT

Questions

Is there a KiCad symbol and footprint for the MMC5983MA?

Yes. The symbol is Sensors:MMC5983MA and the footprint ICs And Semiconductors SMD:PQFN50P300X300X100-16N_a, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MMC5983MA?

LGA-16(3x3), with 16 pins. Its footprint is drawn on this page.

Where is the MMC5983MA datasheet?

MEMSIC publishes it: the Datasheet link on this page opens it.

Where can I order the MMC5983MA?

JLCPCB lists it as part C404329, with 6,736 in stock; the sellers' links on this page open their listings.

Which open-source boards use the MMC5983MA?

95 boards in 73 repositories on GitHub; the most starred are listed on this page, with their KiCad files.