4 layers58.4 × 22.9 mm
Quickfeather board
QuickLogic-Corp/quick-feather-dev-board
100% open source dev kit for EOS S3 MCU+eFPGA SoC supported by fully open source SDK and FPGA Toolchain
101 parts66CC-BY-SA-4.0
4 layers58.4 × 22.9 mm
Quickfeather board
antmicro/quickfeather-dev-board6This project contains open hardware design files for the QuickFeather development board based on the QuickLogic EOS S3 Sensor Processing Platform.
- Size
- 58.4 × 22.9 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 101
- Nets
- 144
- Pads
- 428
- Tracks, vias
- 1,689, 224
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 21 Nov 2019
- Updated
- 18 Mar 2024
Overview
Quickfeather board is an open-source printed circuit board by antmicro, from the antmicro/quickfeather-dev-board repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 4-layer board of 58.4 × 22.9 mm with 101 parts on 144 nets, routed with 1,689 tracks and 224 vias.
It is built around the DPS310, GD25Q16CWIGR and TPS62821DLCR, with the EOSAI-S-PUN64, MC3635 and MCP73831T-2ACI/OT-HXY among its other parts. Its parts include 41 resistors, 19 capacitors, 8 connectors, 7 diodes and 6 ICs.
Main components
12
DPS310
LGA-8(2x2.5)-40℃~+85℃ 0.5pa/K 1.7V~3.6V 100pa 27.6ms 30Kpa~1.2bar 500nA 6pa I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output Yes LGA-8(2x2.5) Pressure Sensors ROHSInfineon TechnologiesPressure Sensors
GD25Q16CWIGR
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 120MHz 16Mbit 1uA 2.7V~3.6V 20 Years 600us SPI WSON-8-EP(5x6) NOR FLASH ROHSGigaDevice Semicon BeijingNOR FLASH
TPS62821DLCR
VSON-8(1.5x2)-40℃~+125℃@(TJ) 1 1A 2.2MHz 2.4V~5.5V 4uA 600mV~4V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Operating status indication、Cycle-by-cycle current limiting、Hiccup current limiting Step-down type Yes VSON-8(1.5x2) DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
EOSAI-S-PUN64
UncategorisedQuickLogic
MC3635
LGA-10(1.6x1.6)-40℃~+85℃ 1.7V~3.6V 100nA 8bit、10bit、12bit、14bit Accelerometer SPI、I2C X,Y,Z ±16g 运动事件检测 LGA-10(1.6x1.6) Accelerometers ROHSMEMSICAccelerometers
MCP73831T-2ACI/OT-HXY
SOT-23-5LBattery ManagementHXY MOSFET
CR0402-FX-1002GLF
0402-55℃~+155℃ 10kΩ 50V 62.5mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface MountCR0402-FX-22R0GLF
0402-55℃~+155℃ 22Ω 50V 62.5mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface Mount
EXB2HV220JV
SMD-16P,3.8x1.6mm16 22Ω 63mW 8 ±200ppm/℃ ±5% SMD-16P,3.8x1.6mm Resistor Networks, Arrays ROHSPanasonicResistor Networks & ArraysCR0402-FX-1000GLF
0402UncategorisedBournsCR0402-FX-1003GLF
0402-55℃~+155℃ 100kΩ 50V 62.5mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface MountCR0402-FX-1501GLF
0402-55℃~+155℃ 1.5kΩ 50V 62.5mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSBournsChip Resistor - Surface Mount
README
README.mdQuickFeather Development Board
Copyright (c) 2019-2024 Antmicro
Overview
This project contains open hardware design files for the QuickFeather development board based on the QuickLogic EOS S3 Sensor Processing Platform. The design files were created by Antmicro in cooperation with QuickLogic. The board has been designed to keep compatibility with the Adafruit Feather ecosystem of evaluation boards. This allows the user to explore functionalities of the EOS S3 platform.
Project structure:
The main directory contains the KiCad design files, LICENSE and README. The remaining files are stored in the following directories:
img- contains graphics for this READMEdoc- contains generated schematics and other documentationlib- contains KiCad component library
Key features
- QuickLogic EOS S3 Processing Platform
- mCube MC3635 accelerometer
- Infineon DPS310 pressure sensor
- Infineon IM69D130 MEMS microphone
- 16Mbit of on-board flash memory
- User button and RGB LED
- Powered from USB or a single Li-Po battery
- Integrated battery charger
- USB data signals tied to programmable logic
- IO signals break-routed into general purpose pinheads
- Compatible with standard 0.1" breadboards
Development ecosystem
Simulation
The board is supported in Renode, the open source simulation framework by Antmicro - you can run a virtual copy of this hardware for software development purposes on your PC. A link to the relevant demo script is provided in Renode's supported boards section.
License
This project is licensed under the CC BY-SA 4.0 DEED license.
Parts
101| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | R_10k_0402 | quickfeather-board-footprints:R_0402_1005Metric | R6, R8, R10, R14, R15, R19, R21, R22, R23, R31, R32, R34, R36, R37 |
| 9 | C_100n_0402 | quickfeather-board-footprints:C_0402_1005Metric | C8, C9, C10, C11, C12, C13, C15, C17, C18 |
| 7 | R_22R_0402 | quickfeather-board-footprints:R_0402_1005Metric | R7, R11, R28, R29, R38, R39, R40 |
| 5 | C_4u7_0603 | quickfeather-board-footprints:C_0603_1608Metric | C1, C2, C5, C14, C16 |
| 4 | 8x22R | quickfeather-board-footprints:R_Array_8x0602_Panasonic_EXB2HV | R30, R33, R41, R42 |
| 4 | MP_Pad3.3mm_Drill2.5mm | quickfeather-board-footprints:MP_Pad3.3mm_Drill2.5mm | MP1, MP2, MP3, MP4 |
| 3 | R_100R_0402 | quickfeather-board-footprints:R_0402_1005Metric | R13, R24, R26 |
| 3 | R_100k_0402 | quickfeather-board-footprints:R_0402_1005Metric | R5, R12, R17 |
| 3 | R_1k5_0402 | quickfeather-board-footprints:R_0402_1005Metric | R3, R9, R27 |
| 3 | R_4k7_0402 | quickfeather-board-footprints:R_0402_1005Metric | R2, R18, R20 |
| 3 | TPD2EUSB30DRTR | quickfeather-board-footprints:SOT-3 | D3, D5, D11 |
| 3 | TP_1mm_SMD | quickfeather-board-footprints:TP_SMD_1mm | TP1, TP2, TP6 |
| 2 | 2N7002PV | quickfeather-board-footprints:SOT-563 | Q2, Q3 |
| 2 | C_12p_0402 | quickfeather-board-footprints:C_0402_1005Metric | C6, C7 |
| 2 | PinHeader_1x2_P2.54mm_Drill1.1mm | quickfeather-board-footprints:PinHeader_1x2_P2.54_Drill0.9mm | J1, J7 |
| 2 | SW_KMR211NGLFS_SMD | quickfeather-board-footprints:SW_KMR211NGLFS_SMD | S1, S2 |
| 1 | 470n/3.6A | quickfeather-board-footprints:L_0806_2016Metric | L1 |
| 1 | 61301611121 | quickfeather-board-footprints:PinHeader_1x16_P2.54mm_Drill1.1mm | J3 |
| 1 | ASMB-MTB1-0A3A2 | quickfeather-board-footprints:PLCC4_3.2x2.8mm | D4 |
| 1 | C_100p_0402 | quickfeather-board-footprints:C_0402_1005Metric | C3 |
| 1 | C_1u_0402 | quickfeather-board-footprints:C_0402_1005Metric | C19 |
| 1 | C_22u_0603 | quickfeather-board-footprints:C_0603_1608Metric | C4 |
| 1 | DMG1012T-7 | quickfeather-board-footprints:SOT-523 | Q4 |
| 1 | DPS310 | quickfeather-board-footprints:LGA-8_2x2.5mm | U4 |
| 1 | EOSAI-S-PUN64 | quickfeather-board-footprints:QFN-64-1EP_8.5x8.5mm_P0.5mm_Lay17x15 | U6 |
| 1 | GD25Q16CWIGR | quickfeather-board-footprints:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4mm | U3 |
| 1 | IM69D130 | quickfeather-board-footprints:IM69D130 | MIC1 |
| 1 | LED_G_0603_LG_L29K-G2J1-24-Z | quickfeather-board-footprints:LED_0603_1608Metric_G | D2 |
| 1 | MBR0520LT1G | quickfeather-board-footprints:D_SOD-123 | D1 |
| 1 | MC3635 | quickfeather-board-footprints:LGA-10_1.6x1.6mm | U5 |
| 1 | MCP73831T-2AC_SOT | quickfeather-board-footprints:SOT-753 | U2 |
| 1 | NX3008CBKV | quickfeather-board-footprints:SOT-666 | Q1 |
| 1 | PinHeader_1x12_P2.54m_Drill1.1mm | quickfeather-board-footprints:PinHeader_1x12_P2.54mm_Drill1.1mm | J2 |
| 1 | PinHeader_2x5_P1.27mm_SMD_Latch | quickfeather-board-footprints:PinHeader_2x5_P1.27mm_SMD_Latch | J6 |
| 1 | PinHeader_2x8_P2.54mm_Drill1mm | quickfeather-board-footprints:PinHeader_2x8_P2.54mm_Drill1.1mm | J8 |
| 1 | R_1M5_0402 | quickfeather-board-footprints:R_0402_1005Metric | R1 |
| 1 | R_200k_0402 | quickfeather-board-footprints:R_0402_1005Metric | R16 |
| 1 | R_220R_0402 | quickfeather-board-footprints:R_0402_1005Metric | R25 |
| 1 | R_453k_0402 | quickfeather-board-footprints:R_0402_1005Metric | R4 |
| 1 | Resonator_32.768kHz_ECX-31B | quickfeather-board-footprints:SMD-2_3.2x1.5mm | X1 |
| 1 | S2B-PH-SM4-TB(LF)(SN) | quickfeather-board-footprints:Conn_JST_PH_1x2_S2B-PH-SM4-TB-LF-SN | J4 |
| 1 | SD05C.TCT | quickfeather-board-footprints:SOD-323 | D6 |
| 1 | TPS62821DLCR | quickfeather-board-footprints:QFN-8_2x1.5mm | U1 |
| 1 | TP_0.75mm_SMD | quickfeather-board-footprints:TP_SMD_0.75mm | TP4 |
| 1 | TP_THT | quickfeather-board-footprints:TP_SMD_1mm | TP5 |
| 1 | USB-Micro-B_Molex_473460001 | quickfeather-board-footprints:USB-Micro-B_Receptacle_Molex_473460001 | J5 |
| 1 | oshw_logo | quickfeather-board-footprints:oshw-logo | N1 |
| 1 | ql_logo | quickfeather-board-footprints:LOGO | N2 |
Questions
How big is the Quickfeather board PCB?
It measures 58.4 × 22.9 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Quickfeather board use?
101 parts, built around the DPS310, GD25Q16CWIGR, TPS62821DLCR and EOSAI-S-PUN64. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Quickfeather board KiCad files?
From the antmicro/quickfeather-dev-board repository on GitHub, at the commit this page was made from: the board is quickfeather-board.kicad_pcb and its schematic quickfeather-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Quickfeather board design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 8 layers90 × 120.4 mm
Ecp5-dc scm
antmicro/ecp5-dc-scm
Experimental Lattice ECP5-driven Data Center Security Communication Module
506 parts23Apache-2.0 - 6 layers52 × 43 mm
Cm4-lvds adapter
antmicro/cm4-baseboard-lvds-adapter
Adapter board converting MIPI DSI into LVDS with additional circuitry for integrating custom displays
155 parts7Apache-2.0 - 2 layers60 × 27 mm
Accelerometer PCB
Radu-Maris/Analog_Devices_Internship_Accelerometer
Built from scratch a PCB that measures the tilt of the device using an accelerometer
81 parts - 6 layers107 × 68 mm
Cm4-baseboard
antmicro/cm4-baseboard
Experimental baseboard supporting System on Modules with Raspberry Pi CM4/CM5 pinout
516 parts36Apache-2.0 - 4 layers80.1 × 22.2 mm
M2-smart iot module
antmicro/m2-smart-iot-module
https://antmicro.com/blog/2021/08/open-hardware-smart-m2-radio-module-for-iot/
212 parts30Apache-2.0 - 2 layers50 × 73 mm
- 2 layers17 × 17 mm
QuickBGA64 cheap
intergalaktik/QuickLogic-EOS-S3-BGA64
Signal Name|Signal Type|I/O Bank|WCLSP Ball|BGA Ball|QFNc|Description|Alternate Function --|--|--|--|--|--|--|-- IO2|IO|VCCIOA|--|A1|6||FBIO2, SPISENSORSSn2, DEBUGMON0, BATTMON, SENSORINT1 IO3|IO|VCCIOA|C7|A2|2||FBIO3…
22 parts1