Skip to the content
12345678

DPS310

Infineon TechnologiesExtended

-40℃~+85℃ 0.5pa/K 1.7V~3.6V 100pa 27.6ms 30Kpa~1.2bar 500nA 6pa I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output Yes LGA-8(2x2.5) Pressure Sensors ROHS

Part id
infineon/DPS310
Category
Pressure Sensors
Package
LGA-8(2x2.5)
Pins
8
In stock
0 at JLCPCB (C130156)
Used on
27 open-source boards

Overview

The DPS310 is a pressure Sensor made by Infineon Technologies in a LGA-8(2x2.5) package with 8 pins. -40℃~+85℃ 0.5pa/K 1.7V~3.6V 100pa 27.6ms 30Kpa~1.2bar 500nA 6pa I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output Yes LGA-8(2x2.5) Pressure Sensors ROHS.

PCBKit's library has its KiCad symbol (DPS310:DPS310, from Antmicro) and its footprint (lga-8-2x2-5mm:LGA-8_2x2.5mm, from Antmicro), ready for a KiCad board. JLCPCB lists it (part C130156). 27 open-source boards in 25 repositories on GitHub use it.

Symbol

1GND2CSB3SDI4SCK5SDO6VDDIO8VDD
DPS310:DPS310From Antmicro

Footprint

12345678
lga-8-2x2-5mm:LGA-8_2x2.5mmFrom Antmicro

From the datasheet

9
Supply, least
1.7 V · VDD, recommended operating min · p. 6
Supply, most
3.6 V · VDD, recommended operating max · p. 6
Supply, least
1.2 V · VDDIO, recommended operating min · p. 6
Supply, absolute maximum
4 V · VDD and VDDIO, absolute max · p. 7
Works from
-40 °C · Ta, operating min · p. 6
Works up to
85 °C · Ta, operating max · p. 6
Takes working
11 µA · typical, standard precision, 1 measurement per second, VDD = VDDIO = 1.8 V · p. 7
Takes at most
345 µA · typical peak during pressure measurement, VDD = VDDIO = 1.8 V · p. 7
Takes asleep
500 nA · typical standby, VDD = VDDIO = 1.8 V · p. 7

What it is and has

13
Measurement range
Pressure: 300–1200 hPa; temperature: -40–85 °C · p. 1
Pressure precision
±0.005 hPa (±0.05 m), high precision mode · p. 1
Relative accuracy
±0.06 hPa (±0.5 m) · p. 1
Absolute accuracy
±1 hPa (±8 m) · p. 1
Temperature accuracy
±0.5°C · p. 1
Pressure temperature sensitivity
0.5Pa/K · p. 1
Measurement result resolution
24 bit · p. 1
Operating modes
Command (manual), Background (automatic), Standby · p. 1
Calibration
Individually calibrated with coefficients for measurement correction · p. 1
FIFO
32 pressure or temperature measurements · p. 1
Interface
I2C and SPI, both with optional interrupt · p. 1
Package
8-pin LGA, 2.0 mm x 2.5 mm x 1.0 mm · p. 1
Compliance
Green Product (RoHS) Compliant · p. 1

Specifications

52
ParameterConditionsAs printedPage
Pressure Pamin 300 · max 1200 hPa6
Temperature Tamin -40 · max 85 °C6
Supply voltage VDDmin 1.7 · max 3.6 V6
Supply voltage IO VDDIOmin 1.2 · max 3.6 V6
Supply voltage ramp-up time tvddupTime for supply voltage to reach 90% of final value.min 0.001 · max 5 ms6
Solder drift1)Minimum solder height 50um. Effects of solder drift can be eliminated by one point calibration.typ 0.8 hPa6
Long term stabilityDepending on environmental conditions; typical value is ±1 hPa.typ 1 hPa6
VDD and VDDIO VDDxx_maxmax 4 V7
Voltage on any pin Vmaxmax 4 V7
Storage temperature Tsmin -40 · max 125 °C7
Pressure Pmaxmax 10000 hPa7
ESD VESD_HBMHBM (JS001)min -2 · max 2 KV7
Peak Current Consumption IpeakDuring Pressure measurement; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 345 uA7
Peak Current Consumption IpeakDuring Temperature measurement; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 280 uA7
Standby Current Consumption IstbVDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 0.5 uA7
Current Consumption. ( 1 measurement per second.) I1HzLow precision; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 2.1 uA7
Current Consumption. ( 1 measurement per second.) I1HzStandard precision; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 11 uA7
Current Consumption. ( 1 measurement per second.) I1HzHigh precision; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 38 uA7
Temperature accuracy AtTypical accuracy +/-0.5°C; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 0.5 °C8
Temperature data resolution At_resVDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 0.01 °C8
Temperature measurement rate fVDD=1.8V, VDDIO=1.8V.min 1 · max 128 Hz8
Absolute pressure accuracy Ap_absAfter one point calibration; typical accuracy +/-10 Pa; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 10 Pa9
Absolute pressure accuracy Ap_absPA=300-1200hPa, TA=0 +65°C, excluding solder effects; typical accuracy +/-100 Pa; VDD=1.8V, VDDIO=1.8V.typ 100 Pa9
Relative pressure accuracy Ap_relAny Δ1hPa in PA=800-1200hPa, any constant temperature in TA=20 +60°C; typical accuracy +/-6 Pa; VDD=1.8V, VDDIO=1.8V.typ 6 Pa9
Pressure precision Ap_prcLow Power; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 5 PaRMS9
Pressure precision Ap_prcStandard; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 1.2 PaRMS9
Pressure precision Ap_prcHigh Precision; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 0.5 PaRMS9
Power supply rejection Ap_psrMeasured with 217Hz square wave and broad band noise, 100mVpp; VDD=1.8V, VDDIO=1.8V.max 0.063 PaRMS9
Pressure temperature sensitivity of calibrated measurements Ap_tmp1000hPa, 25 +65°C; VDD=1.8V, VDDIO=1.8V.typ 0.5 Pa/K9
Pressure data resolution Ap_resVDD=1.8V, VDDIO=1.8V.max 0.06 PaRMS9
Pressure measurement rate fVDD=1.8V, VDDIO=1.8V.min 1 · max 128 Hz9
Pressure measurement time tLow Power; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 5.2 ms9
Pressure measurement time tStandard; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 27.6 ms9
Pressure measurement time tHigh Precision; VDD=1.8V, VDDIO=1.8V, PA=1000hPa, TA=25°C.typ 105 ms9
Time to sensor ready TSensor_rdyFrom VDD > 1.2V & VDDIO > 0.6V or Soft Reset; SENSOR_RDY indicates sensor ready.max 12 ms10
Time to coefficients are available. TCoef_rdyFrom VDD > 1.2V & VDDIO > 0.6V or Soft Reset; COEF_RDY indicates coefficients can be read.max 40 ms10
I2C Clock. fI2Cmax 3.4 MHz10
SPI Clock fSPImax 10 MHz10
Pull-up resistor RpullInternal pull-up resistance to VDDIO.min 60 · typ 120 · max 180 kohm22
I2C bus load capacitor CbOn SDI and SCK.max 400 pF22
Data setup time on SDI pin tSetupS&F modemin 20 ns23
Data setup time on SDI pin tSetupHS modemin 5 ns23
Data hold time on SDI pin tHoldS&F&HSmodemin 0 ns23
Duty Cycle DCS&F modemax 70 %23
Duty Cycle DCHS modemax 55 %23
Duty Cycle (Thigh%) SPI_DCVDDIO = 1.2V; 4-wire and 3-wire SPI.min 30 %24
Duty Cycle (Thigh%) SPI_DCVDDIO = 1.8V/3.6V; 4-wire and 3-wire SPI.min 20 %24
SDI setup time T_setup_sdi4-wire and 3-wire SPI.min 2 ns24
SDI hold time T_hold_sdi4-wire and 3-wire SPI.min 2 ns24
Clock SPI_CLK4-wire and 3-wire SPI.max 10 MHz24
CSB setup time T_setup_csb4-wire and 3-wire SPI.min 15 ns24
CSB hold time4-wire and 3-wire SPI.min 15 ns24

Pins, by the datasheet

8
1 GND
Ground. · p. 5
2 CSB
Active-low SPI chip select; in I2C mode leave open with internal pull-up or tie to VDDIO. · p. 5
3 SDI
Serial data input/output in SPI 3-wire and I2C modes; serial data input in SPI 4-wire mode. · p. 5
4 SCK
Serial Clock. · p. 5
5 SDO
SPI 4-wire serial data output; optional interrupt in SPI 3-wire or I2C mode; I2C device address least significant bit; unused in SPI 3-wire without interrupt. · p. 5
6 VDDIO
Digital supply voltage for digital blocks and I/O interface. · p. 5
7 GND
Ground. · p. 5
8 VDD
Supply voltage for analog blocks. · p. 5

Open-source boards using it

27See all 27
  • 4 layers58.4 × 22.9 mmQuickfeather board, the printed circuit board in 3D

    Quickfeather board

    QuickLogic-Corp/quick-feather-dev-board

    100% open source dev kit for EOS S3 MCU+eFPGA SoC supported by fully open source SDK and FPGA Toolchain

    101 parts66CC-BY-SA-4.0
  • 4 layers34 × 40 mmWingFC, the printed circuit board in 3D

    WingFC

    BryanSouza91/WingFC

    WingFC is an open-source embedded flight controller for sub-250g fixed-wing aircraft, built with TinyGo. It provides stabilization, mixing, and safety features for elevon-equipped models, with a focus on reliability and…

    38 parts10MIT
  • 6 layers36 × 36 mmUltimateFC, the printed circuit board in 3D

    UltimateFC

    crteensy/yolo-chonker

    betaflight developer FC for the H735

    245 parts10CC-BY-SA-4.0
  • 6 layers100 × 60 mmAether, the printed circuit board in 3D

    Aether

    nasheed-x/aether

    Aether is a versatile flight computer for testing flight hardware and software, focusing on sensor fusion to monitor rocket states and interface with on-board systems.

    180 parts10
  • 2 layers70 × 70 mmAirSensor display, the printed circuit board in 3D

    AirSensor display

    MarcFinns/AirSensor-for-HomeAssistant

    AirSensor for HomeAssistant (hardware and software)

    30 parts8
  • 4 layers58.4 × 22.9 mmQuickfeather board, the printed circuit board in 3D

    Quickfeather board

    antmicro/quickfeather-dev-board

    This project contains open hardware design files for the QuickFeather development board based on the QuickLogic EOS S3 Sensor Processing Platform.

    101 parts6CC-BY-SA-4.0
  • 2 layers25 × 50 mmNuernberg Sensor, the printed circuit board in 3D

    Nuernberg Sensor

    opendata-nuernberg/open-sensor-platform

    Hardware Designs and Firmware of the Open Sensor Platform

    40 parts2MIT
  • 4 layers54.5 × 18 mmRicardo Altimeter, the printed circuit board in 3D

    Ricardo Altimeter

    icl-rocketry/Ricardo-Altimeter

    Altimeter for Electronics Team

    103 parts1

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the DPS310?

Yes. The symbol is DPS310:DPS310 and the footprint lga-8-2x2-5mm:LGA-8_2x2.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DPS310?

LGA-8(2x2.5), with 8 pins. Its footprint is drawn on this page.

Where is the DPS310 datasheet?

Infineon Technologies publishes it: the Datasheet link on this page opens it.

Where can I order the DPS310?

JLCPCB lists it as part C130156, with 0 in stock; the sellers' links on this page open their listings.

What can replace the DPS310?

Parts like it in the library: the DPS310XTSA1 by Infineon Technologies. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DPS310?

27 boards in 25 repositories on GitHub; the most starred are listed on this page, with their KiCad files.