

USB LiDAR VL53L9
USB accessory device with VL53L9 Time of Flight sensor (dToF 3D LiDAR) & 6-axis IMU
- Size
- 34 × 30.2 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 72
- Nets
- 64
- Pads
- 281
- Tracks, vias
- 618, 125
- Pours
- 257
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 26 Jun 2026
- Updated
- 12 Sep 2026
Overview
USB LiDAR VL53L9 is an open-source printed circuit board by RemiFM, from the RemiFM/USB-LiDAR-VL53L9 repository on GitHub, published under the MIT licence. It is a 6-layer board of 34 × 30.2 mm with 72 parts on 64 nets, routed with 618 tracks and 125 vias.
It is built around the STM32C552KEU6, LM3670MF-3.3 and 74LVC1T45W6, with the LSF0102DP, LSM6DSV and TLV73312PDBV among its other parts. Its parts include 33 capacitors, 16 resistors, 12 ICs, 3 diodes and 2 connectors. It belongs with the sensors and measurement boards and the STM32 boards of this library.
Main components
11STM32C552KEU6
UFQFPN-32(5x5)UFQFPN-32(5x5) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)LM3670MF-3.3
SOT-23-5-40℃~+85℃@(TA) 1 15uA 1MHz 2.5V~5.5V 3.3V 350mA Buck Buck Built-in Fixed Yes SOT-23-5 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters74LVC1T45W6
SOT-26-40℃~+125℃ 1 1 1.65V~5.5V 1.65V~5.5V Bidirectional Power-Off Protection Tri-State SOT-26 Translators, Level Shifters ROHSDiodes IncorporatedTranslators, Level ShiftersLSF0102DP
TSSOP82-Bit Bidirectional Multi-Voltage Level Translator; Open-Drain; Push-PullNexperiaUncategorisedLSM6DSV
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 4.5KB Accelerometer Gyroscope SPI、I2C、I3C X,Y,Z X,Y,Z ±16g ±4000dps LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometersTLV73312PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V 120uVrms 125mV@(300mA) 300mA 34uA 5.5V 50dB Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV73318PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.8V 120uVrms 125mV@(300mA) 300mA 34uA 5.5V 68dB@(100Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV73328PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 125mV@(300mA) 2.8V 300mA 34uA 5.5V 50dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Soft Start、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)DF2B7AE,H3F
SC-79(SOD-523)100nA 20V 4A@8/20us 5.5V 6.8V 8.5pF 80W@8/20us Bidirectional IEC 61000-4-2 TVS SC-79(SOD-523) ESD and Surge Protection (TVS/ESD) ROHSToshibaESD And Surge Protection (TVS/ESD)USB4106-GF-A
-- HWDG ROHSGlobal Connector Technology (GCT)Uncategorised
README
README.mdUSB-C LiDAR Node (VL53L9)
A compact and low-cost USB device with integrated LiDAR sensor and IMU. This hardware node packages STMicroelectronics' VL53L9 advanced direct Time-of-Flight (dToF) matrix LiDAR with a 6-axis IMU into a plug-and-play USB-C device. Designed for mobile robotics, micro-UAVs, and academic SLAM research. The hardware is designed in KiCad 10.
System Architecture

| Feature | Detail | Datasheet |
|---|---|---|
| LiDAR | ST VL53L9CX dToF module with up to 54×42 (2.3 k) discrete ranging zones, 5 cm–8.8 m range | link |
| IMU | ST LSM6DSV 6-axis IMU with embedded sensor fusion engine, orientation quaternions generated on-chip | link |
Data Format
Raw binary packet framing is used instead of verbose text formats (JSON/CSV) to stay well within the 12 Mbps USB Full-Speed ceiling while imposing zero processing overhead on the MCU.
Per the VL53L9CX datasheet (DS14879, Table 2), the I3C interface is specified for a 12.5 MHz bus clock and a 12.5 Mbps output data rate. Full resolution is hard-limited to 30 Hz. Two pre-configured profiles are available:
| Profile | Output Matrix | Frame Rate |
|---|---|---|
| Full Resolution (default) | 54 × 42 zones | 30 Hz |
| Binned Navigation (high-velocity) | 24 × 20 zones | 60 Hz |
Mechanical Specs
The PCB measures 34 × 30 mm and has 4× M3 mounting holes on a 20 mm square pitch, fitting small drone frame stacks.
Parts
72| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100nF | Capacitor_SMD:C_0603_1608Metric | C12, C15, C21, C22, C23, C26, C27, C30, C31, C32, C33, C34, C35 |
| 8 | 1µF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C9, C25 |
| 5 | 4.7µF | Capacitor_SMD:C_0603_1608Metric | C7, C10, C11, C16, C24 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric | R8, R11, R16, R17 |
| 2 | 100R | Resistor_SMD:R_0603_1608Metric | R12, R13 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C18, C19 |
| 2 | 10µF | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | 2k2 | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | 74LVC1T45 | USB-LiDAR-VL53L9:Diodes_Inc_SOT363 | U13, U14 |
| 1 | +5V | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 16MHz | Crystal:Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R23 |
| 1 | 1X6 P0.5" | USB-LiDAR-VL53L9:Connector_TH_1x06_P1.27mm | J3 |
| 1 | 1k@100MHz | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | 2.2µF | Capacitor_SMD:C_0603_1608Metric | C20 |
| 1 | 200k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 22R | Resistor_SMD:R_0603_1608Metric | R15 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | 4.7nF | Capacitor_SMD:C_0805_2012Metric | C36 |
| 1 | 4.7µH | Inductor_SMD:L_1008_2520Metric | L1 |
| 1 | 47µF | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | DF2B7AE,H3F | Diode_SMD:D_SOD-523 | D2 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | LED GREEN | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | LED RED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | LM3670MF-3.3 | USB-LiDAR-VL53L9:TI_SOT23_DBV0005A | U7 |
| 1 | LSF0102 | USB-LiDAR-VL53L9:TI_VSSOP_DCU0008A | U8 |
| 1 | LSM6DSV | USB-LiDAR-VL53L9:ST_LSM6DSV | U3 |
| 1 | SN74AXC1T45DCKR | USB-LiDAR-VL53L9:TI_SOT363-DCK0006A | U12 |
| 1 | STM32C552KEU6 | USB-LiDAR-VL53L9:ST_UFQFPN32 | U2 |
| 1 | TLV73312PDBV | USB-LiDAR-VL53L9:TI_SOT23_DBV0005A | U4 |
| 1 | TLV73318PDBV | USB-LiDAR-VL53L9:TI_SOT23_DBV0005A | U5 |
| 1 | TLV73328PDBV | USB-LiDAR-VL53L9:TI_SOT23_DBV0005A | U6 |
| 1 | USB4106 | USB-LiDAR-VL53L9:GCT_USB4106 | J1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U10 |
| 1 | VL53L9CX | USB-LiDAR-VL53L9:ST_VL53L9CX | U1 |
Similar boards
- 6 layers60.6 × 100 mm

- 4 layers117.5 × 30 mm

- 2 layers69 × 112.2 mm

UltraPCB KiCAD
enliktjioe/three-workshops
HfK Bremen - Three Workshops course from Ralf Baecker
52 partsGPL-3.0 - 4 layers85 × 88 mm

- 2 layers133.7 × 120.8 mm

3phaseDiverter
FredM67/PVRouter-KiCad
Fichiers de conception KiCad pour le Mk2 PV Router — un système open-source de routage solaire photovoltaïque universel (monophasé, triphasé avec ou sans neutre, biphasé).
204 partsCC-BY-SA-4.0 - 2 layers280 × 110 mm

PCB Piano v1.1
ninjatill/PCB-Capacitive-Touch-Synth
A Raspberry Pi-based synthesizer with capacitive touch keys directly on a PCB.
284 parts - 4 layers135.5 × 25 mm

Obstacle detector
farhanarrafi/embedded-project-website
UNT Embedded Hardware/Software Design Course Report
12 parts - 4 layers128 × 85 mm

Questions
How big is the USB LiDAR VL53L9 PCB?
It measures 34 × 30.2 mm and has 6 copper layers, 1.6 mm thick.
What parts does the USB LiDAR VL53L9 use?
72 parts, built around the STM32C552KEU6, LM3670MF-3.3, 74LVC1T45W6 and LSF0102DP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the USB LiDAR VL53L9 KiCad files?
From the RemiFM/USB-LiDAR-VL53L9 repository on GitHub, at the commit this page was made from: the board is pcb/USB-LiDAR-VL53L9.kicad_pcb and its schematic pcb/CAN.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the USB LiDAR VL53L9 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).