
TLV73312PDBV
Texas InstrumentsExtended
-40℃~+125℃@(Tj) 1 1.2V 120uVrms 125mV@(300mA) 300mA 34uA 5.5V 50dB Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS
- Part id
- ti/TLV73312PDBV
- Category
- Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
- Package
- SOT-23-5
- Pins
- 5
- In stock
- 36 at JLCPCB (C2871228)
- Used on
- 13 open-source boards
Overview
The TLV73312PDBV is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃@(Tj) 1 1.2V 120uVrms 125mV@(300mA) 300mA 34uA 5.5V 50dB Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.
PCBKit's library has its KiCad symbol (Regulator_Linear:TLV73312PDBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 36 are in stock at JLCPCB (part C2871228). 13 open-source boards in 12 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
13- Supply, least
- 1.4 V · VIN, recommended operating min · p. 5
- Supply, most
- 5.5 V · VIN, recommended operating max · p. 5
- Supply, absolute maximum
- 6 V · VIN, absolute max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature absolute max · p. 5
- Takes working
- 34 µA · Ground pin current typical, IOUT = 0 mA · p. 6
- Takes asleep
- 100 nA · Shutdown current typical, VEN ≤ 0.35 V, TJ = 25°C · p. 6
- Gives
- 300 mA · Recommended continuous output current max · p. 5
- Current limit
- 360 mA · Output current limit min · p. 6
- Dropout
- 420 mV · Dropout max at 300 mA, 1.2 V output, –40°C ≤ TJ ≤ 85°C · p. 6
- Dropout
- 450 mV · Dropout max at 300 mA, 1.2 V output, –40°C ≤ TJ ≤ 125°C · p. 6
- Junction to air (DBV (SOT-23))
- 228.4 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to board (DBV (SOT-23))
- 55.8 K/W · Junction-to-board thermal resistance · p. 5
- Junction to case (DBV (SOT-23))
- 151.5 K/W · Junction-to-case top thermal resistance · p. 5
What it is and has
5- Capacitor-free operation
- Stable with or without capacitors · p. 1
- Protection
- Foldback overcurrent protection · p. 1
- Output accuracy
- 1% typical, 1.4% maximum · p. 1
- Output discharge
- Active output discharge · p. 1
- Package
- SOT-23, 5 pins · p. 4
Around it
2- cap small capacitor
- between IN and GND; Recommended at the input pin; capacitance is not specified on this page. · p. 4
- cap 1-μF
- between OUT and GND; Ceramic; recommended for best transient response. · p. 4
Specifications
35| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Voltage VIN | With respect to GND | min -0.3 · max 6 V | 5 |
| Voltage VEN | With respect to GND; maximum VIN + 0.3 V | min -0.3 V | 5 |
| Voltage VOUT | With respect to GND | min -0.3 · max 3.6 V | 5 |
| Temperature TJ | Operating junction | min -40 · max 150 °C | 5 |
| Temperature Tstg | Storage | min -65 · max 160 °C | 5 |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V | max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 V | max 500 V | 5 |
| Input range, VIN VIN | Over operating junction temperature range | min 1.4 · max 5.5 V | 5 |
| Output range, VOUT VOUT | Family output range | min 1 · max 3.3 V | 5 |
| Output current, IOUT IOUT | Over operating junction temperature range | min 0 · max 300 mA | 5 |
| Enable range, VEN VEN | Maximum VIN | min 0 V | 5 |
| Junction temperature, TJ TJ | min -40 · max 125 °C | 5 | |
| Junction-to-ambient thermal resistance RθJA | DBV (SOT-23), 5 PINS | typ 228.4 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | DBV (SOT-23), 5 PINS | typ 151.5 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | DBV (SOT-23), 5 PINS | typ 55.8 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | DBV (SOT-23), 5 PINS | typ 31.4 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | DBV (SOT-23), 5 PINS | typ 54.8 °C/W | 5 |
| Input voltage VIN | TJ = –40°C to +125°C | min 1.4 · max 5.5 V | 6 |
| DC output accuracy | TJ = 25°C | min -1 · max 1 % | 6 |
| DC output accuracy | –40°C ≤ TJ ≤ +125°C | min -1.4 · max 1.4 % | 6 |
| Undervoltage lockout UVLO | VIN rising | typ 1.3 · max 1.4 V | 6 |
| Undervoltage lockout UVLO | VIN falling | typ 1.25 V | 6 |
| Line regulation ΔVO(ΔVI) | ΔVI = VIN(nom) to VIN(nom) + 1 | typ 1 mV | 6 |
| Load regulation ΔVO(ΔIO) | ΔIO = 1 mA to 300 mA, DBV package | typ 25 mV | 6 |
| Dropout voltage (1) VDO | VOUT = 0.98 × VOUT(nom), IOUT = 300 mA; 1.2 V ≤ VOUT < 1.5 V, –40°C ≤ TJ ≤ 85°C | max 420 mV | 6 |
| Dropout voltage (1) VDO | VOUT = 0.98 × VOUT(nom), IOUT = 300 mA; 1.2 V ≤ VOUT < 1.5 V, –40°C ≤ TJ ≤ 125°C | max 450 mV | 6 |
| Ground pin current IGND | IOUT = 0 mA | typ 34 · max 60 uA | 6 |
| Shutdown current ISHDN | VEN ≤ 0.35 V, 2.0 V ≤ VIN ≤ 5.5 V, TJ = 25°C | typ 0.1 · max 1 uA | 6 |
| EN pin high voltage (enabled) VEN(HI) | min 0.9 V | 6 | |
| EN pin low voltage (disabled) VEN(LO) | max 0.35 V | 6 | |
| EN pin current IEN | VEN = 5.5 V | typ 0.01 uA | 6 |
| Pull-down resistor | VIN = 2.3 V | typ 120 Ω | 6 |
| Output current limit ILIM | min 360 · max 700 mA | 6 | |
| Thermal shutdown Tsd | Shutdown, temperature increasing | typ 160 °C | 6 |
| Thermal shutdown Tsd | Reset, temperature decreasing | typ 140 °C | 6 |
Pins, by the datasheet
5- 1 IN
- Input pin; a small capacitor to ground is recommended. · p. 4
- 2 GND
- Ground pin. · p. 4
- 3 EN
- Drive above VEN(HI) to enable the regulator or below VEN(LO) for shutdown. · p. 4
- 4 NC
- No internal connection. · p. 4
- 5 OUT
- Regulated output; use a small 1-uF ceramic capacitor to ground for best transient response. · p. 4
- 2 layers100 × 68 mm

- 4 layers117.5 × 30 mm

- 6 layers34 × 30.2 mm

USB LiDAR VL53L9
RemiFM/USB-LiDAR-VL53L9
USB accessory device with VL53L9 Time of Flight sensor (dToF 3D LiDAR) & 6-axis IMU
72 parts24MIT - 4 layers30.9 × 30.9 mm

Fpv video in v1
Cinetronix/fpv-video-in-v1
KiCad hardware design for an HDMI-to-MIPI CSI bridge board, designed for FPV camera systems.
48 parts11 - 2 layers96.5 × 96.5 mm

Transmitter Main Board
akreager/rc-transmitter
Open-source design for 3D printed pistol-grip RC Transmitter.
49 parts1GPL-3.0 - 6 layers60.6 × 100 mm

- 2 layers97.6 × 74.6 mm

- 2 layers

Pcb dev fpga iCE40
shishir-dey/pcb-dev-fpga-iCE40
A 2 layer development board with a Lattice Semiconductor ICE40UP5K-SG48ITR FPGA. Made with KiCad
57 partsMIT
Parts like it
8ME6211C12M5G-N
SOT-23-5-40℃~+150℃ 1 1.2V 280mV@(100mA)、500mV@(200mA) 300mA 30uA 50uVrms 6V 70dB@(1kHz) Fixed Over Current Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV74312PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V 120uVrms 300mA 34uA 420mV@(300mA) 5.5V 50dB@(1kHz) Fixed Over Current Protection、Enable、Thermal Shutdown Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMIC5504-1.2YM5-TR
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V 175uVrms 300mA 380mV@(300mA) 5.5V 55uA 60dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTLV75712PDBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V 1A 25uA 425mV@(1A) 45dB@(100kHz) 5.5V 71.5uVrms Fixed Positive Under Voltage Lockout、Over Current Protection、Soft Start、Thermal Shutdown SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPRT9193-12GB
SOT-23-5-40℃~+85℃@(Ta) 1 1.2V 300mA 50uVrms 6V 70dB@(1kHz) Fixed Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsCJ6205B12M
SOT-23-5L-40℃~+85℃@(Ta) 1 1.2V 150mV@(150mA) 40uVrms 500mA 50uA 6V 75dB@(1kHz) Fixed Over Current Protection、Short Circuit Protection Positive SOT-23-5L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSJiangsu Changjing Electronics Technology (CJ)Voltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLP3984-12B5F
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V 300mA 300mV@(300mA) 300uVrms 5.5V 68dB@(1kHz) Fixed Over Current Protection、Thermal Shutdown Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSLOWPOWERVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSPX3819M5-L-1-2/TR
SOT-23-5-40℃~+125℃@(Tj) 1 1.2V 20V 40uVrms 500mA 700mV@(500mA) 70dB 90uA Fixed Over Current Protection、Over Temperature Protection、Reverse connection protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMaxLinearVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Questions
Is there a KiCad symbol and footprint for the TLV73312PDBV?
Yes. The symbol is Regulator_Linear:TLV73312PDBV and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TLV73312PDBV?
SOT-23-5, with 5 pins. Its footprint is drawn on this page.
Where is the TLV73312PDBV datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TLV73312PDBV?
JLCPCB lists it as part C2871228, with 36 in stock; the sellers' links on this page open their listings.
What can replace the TLV73312PDBV?
Parts like it in the library: the ME6211C12M5G-N by MICRONE, the TLV74312PDBV by Texas Instruments, the MIC5504-1.2YM5-TR by Microchip Technology and the TLV75712PDBV by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TLV73312PDBV?
13 boards in 12 repositories on GitHub; the most starred are listed on this page, with their KiCad files.