Skip to the content
2 layers280 × 110 mmPCB Piano v1.1, the printed circuit board in 3D

A Raspberry Pi-based synthesizer with capacitive touch keys directly on a PCB.

Size
280 × 110 mm
Copper layers
2
Thickness
1.6 mm
Parts
284
Nets
244
Pads
966
Tracks, vias
2,573, 1,398
Pours
62
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
11 May 2026
Updated
19 Jun 2026

Overview

PCB Piano v1.1 is an open-source printed circuit board by ninjatill, from the ninjatill/PCB-Capacitive-Touch-Synth repository on GitHub. It is a 2-layer board of 280 × 110 mm with 284 parts on 244 nets, routed with 2,573 tracks and 1,398 vias.

It is built around the RP2040, 74AHCT2G125DP and PCA9685BS, with the MTCH2120-V/REB, W25Q128JVPIQ and TPS63001DRC among its other parts. Its parts include 76 capacitors, 68 resistors, 42 diodes, 14 ICs and 9 connectors. It belongs with the audio and music boards and the RP2040 boards of this library.

Main components

12

README

README.md

PCB-Capacitive-Touch-Synth

A Raspberry Pi-based synthesizer with capacitive touch keys directly on a PCB.

Licensing

Hardware

All files in /hardware are licensed under:

CC BY-NC-SA 4.0

Firmware

All files in /firmware are licensed under:

GPLv3

Concept

The PCB-Capacitive-Touch-Synth started as a sub-component of a larger science fair project. For my daughter's next science fair project (5th grade), she chose to create Plasma Speakers as we saw on the Franzoli Electronics YouTube page. The plasma speakers are flyback transformers that create a high-voltage arc (which ionizes the air into plasma). The frequeny of the arc creates audio tones. On Franzoli's demonstration videos, he plays MIDI-style music with each speaker acting as a left or right channel/voice. That is the concept we want to re-create.

If we re-create the plasma speakers, then how do we make then into an interactive display for the fair? Well, what if we had 2 midi-controller keyboards hooked up to a host PC. The host PC would do the heavy lifting of audio generation and output to the plasma speakers. Each keyboard would play its notes through either the left or right channel respectively. That's the main idea: 2 keyboards, a host PC, and plasma speakers.

To source the midi keyboards, you could go to Amazon and pick up a 30$-70$ keyboard (higher-end small midi keyboards can run upwards of 200-500$). But, commercial MIDI controllers usually do not output sound directly, it requires a host PC; so its usefullness outside the fair display is limited. The size and scale of the keyboards should be small (to match the entire setup which is portable and compact for a 36"-48" display.) The speakers on Franzoli's demos are very industrial/scientific looking. I thought commercial keyboards would look out of place or be too expensive. So I had a concept of creating keyboards printed on PCBs using capacitive touch buttons. The keyboards would be build to our specific needs and we can build in many features because of the DIY nature.

I decided the best course of action was to have my daughter re-create Fanzoli's Easy-Flyback circuits. It will teach her basic electrical components, schematic creation and PCB layout and fabrication. I think that's a wealth of knowledge for a 10 year old (maybe 11 by the time this comes to fruition). I will handle creating the PCB Capacitive Touch Synthesizer. It is a large complex project and is difficult for my own skill set.

Documentation

Concept to Schematic

As an electrical engineer, I have created PCBs for simple devices. A capacitive touch synthesizer is the largest project/PCB I will have created. So, to jumpstart the project, I consulted my new "friend", ChatGPT. ChatGPT was able to answer questions and make recommendations faster than I could search DigiKey/Mouser, review datasheets, and find the right combination of ICs. But to be clear, I was driving the design. I wanted specific features and ChatGPT helped me realize those features faster than I could alone.

I started with the following design critera

  • The front of the keyboard should be as flat as possible both for aestectic and functional reasons.
    • Aesthetically, I don't want a lot of clutter on the front of the board.
    • Functionally, Children will be interacting with this. I don't want exposed chip leads or solder pads. I also don't want through hole components sticking up with sharp edges. If kids can touch it, they will.
  • The keyboard should be as small as possible but still allowing for decent usability (key widths wide enough for easy touch, etc.)

From the design criteria, we landed with some of the following choices:

  • We will use capacitive touch sensors for the piano keys. Capacitive touch reduces mechanical parts that need fabricated (via 3D printing). It's more touch-friendly than many momentary push buttons.
  • We will keep all IC's on the back of the board. Only LEDs and a volume knob will protrude from the front.
  • We will use only surface mount components (to eliminate protrusions through the board and maintain the flat asthetic.)
  • We will 3D print a back cover that serves 2 purposes:
    • It will cover the back circuitry to prevent tampering.
    • It will raise the PCB off the display surface by a comfortable distance (and tilt it forward a few degrees) to increase usability.

Basic Functionality

  • The synthesizer will funtion in two main modes: standalone and MIDI.
    • In standalone mode, the keyboard will generate its own sounds via speaker or headphones.
    • In MIDI mode, the keyboard will send MIDI commands to a host PC (this is the intended mode for the science fair.

Parts

284
QtyValueFootprintReferences
3610kResistor_SMD:R_0603_1608MetricR22, R23, R24, R28, R29, R30, R31, R32, R34, R42, R43, R44, R45, R46, R47, R48 +20
353.3fV 180mcdPCBPiano_Footprints:LED_0603_1608MetricD10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25 +19
33.1uFCapacitor_SMD:C_0603_1608MetricC4, C14, C17, C19, C22, C25, C28, C29, C30, C32, C33, C34, C35, C38, C41, C43 +17
20~PCBPiano_Footprints:Pad_Solder_SMT_5x7mmSP1, SP2, SP3, SP4, SP5, SP10, SP11, SP12, SP13, SP14, SP15, SP16, SP17, SP18, SP19, SP20 +4
141uFCapacitor_SMD:C_0603_1608MetricC3, C6, C8, C13, C18, C23, C24, C31, C37, C44, C45, C50, C66, C74
13100kResistor_SMD:R_0603_1608MetricR12, R14, R25, R26, R27, R36, R37, R67, R69, R70, R73, R74, R79
1310uFCapacitor_SMD:C_0805_2012MetricC49, C52, C54, C56, C58, C63, C67, C77, C80, C81, C82, C83, C84
12~PCBPiano_Footprints:Touchpad_WhiteKeyTP1, TP3, TP5, TP7, TP8, TP10, TP12, TP13, TP15, TP17, TP19, TP20
8180 OhmPCBPiano_Footprints:R_Array_Convex_4x1206RN1, RN2, RN3, RN4, RN5, RN6, RN7, RN8
847uFCapacitor_Tantalum_SMD:CP_EIA-3528-15_AVX-HC15, C20, C21, C42, C60, C62, C78, C79
8~PCBPiano_Footprints:Touchpad_BlackKeyTP2, TP4, TP6, TP9, TP11, TP14, TP16, TP18
627Resistor_SMD:R_0603_1608MetricR15, R16, R38, R39, R40, R41
5MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4, H5
44.7kResistor_SMD:R_0603_1608MetricR17, R18, R19, R20
4ESD321PCBPiano_Footprints:D_SOD-523D1, D2, D3, D4
4~PCBPiano_Footprints:Touchpad_Circle_10mmTP21, TP22, TP23, TP24
31.5kResistor_SMD:R_0603_1608MetricR75, R76, R77
3FiducialFiducial:Fiducial_1mm_Mask3mmFID1, FID2, FID3
3PinHeader 1x02 SMTConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical_SMD_Pin1RightJ4, J5, J8
2100uFCapacitor_SMD:C_1206_3216MetricC26, C27
21kResistor_SMD:R_0603_1608MetricR33, R72
227pFCapacitor_SMD:C_0603_1608MetricC39, C40
2Dotstar LEDPCBPiano_Footprints:APA102-2020D40, D41
2LED ControllerPCBPiano_Footprints:NXP_HVQFN-28_6mmx6mmx0.85mmU4, U6
2Pushbutton MOPCBPiano_Footprints:SW_SWT0115-020025SSA_REVASW2, SW3
2SolderJumper_2_OpenPCBPiano_Footprints:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1, JP2
2Touch ControllerPackage_DFN_QFN:VQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mmU5, U10
11.8VPackage_TO_SOT_SMD:SOT-23-5U12
1100Resistor_SMD:R_0603_1608MetricR10
1128MBitPackage_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mmU7
112MHzCrystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mmY1
1150Resistor_SMD:R_1206_3216MetricR71
11:2 USB MUXPCBPiano_Footprints:TQFN-10_ZL_1.6x1.3mm_P0.4mmU14
11FPCBPiano_Footprints:SuperCap_HType_FoldedOutLegsC2
11uHPCBPiano_Footprints:L_Sumida_0530CDMCCDS-1R0MC_5.4x5.2mmL3
12.2kResistor_SMD:R_0603_1608MetricR35
12.2uHPCBPiano_Footprints:L_Pulse_BMRB00060630_7.3x6.6mmL2
12.2uHPCBPiano_Footprints:L_Bourns_SRP4020T_4.06x4.45x2.0mmL1
1220pFCapacitor_SMD:C_0603_1608MetricC36
122nFCapacitor_SMD:C_0805_2012MetricC75
13.3VPCBPiano_Footprints:Texas_DRC0010JU8
13.5mm TRRSPCBPiano_Footprints:AudioJack_TRS_Switch_TR1R2S_SJ3-35024K-SMT-TRJ3
132.768kHzPCBPiano_Footprints:Crystal_Kyocera_DT32_3.2x1.5mmY2
147uFCapacitor_Tantalum_SMD:CP_EIA-7343-43_Kemet-XC1
15VPackage_TO_SOT_SMD:SOT-563U9
1732kResistor_SMD:R_0603_1608MetricR11
1Audio DAC Class-D I2S/I2CPackage_DFN_QFN:Texas_RHB0032E_VQFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mmU11
1Dual Line BufferPackage_SO:VSSOP-8_2.3x2mm_P0.5mmU2
1JST PH 4-PINConnector_JST:JST_PH_B4B-PH-SM4-TB_1x04-1MP_P2.00mm_VerticalJ2
1JST-PH 1x03 SMTConnector_JST:JST_PH_B3B-PH-SM4-TB_1x03-1MP_P2.00mm_VerticalSW1
1JST-PH 2-PIN SMTConnector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_VerticalJ11
1MEMS I2S MicrophonePCBPiano_Footprints:InvenSense_ICS-43432-7_4x3mmMK1
1MER1045-24PCBPiano_Footprints:Switch_RotaryEncoder_MER1045-24SW4
1MFS 126 DPCBPiano_Footprints:Switch_Slide_MFS126E_PanelCutoutSWCUT1
1P-Ch Power MOSFETPCBPiano_Footprints:PPAK_3x3Q1
1PinHeader 2x10 SMT Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical_SMDJ7
1RP2040Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mmU1
1RTCPackage_DFN_QFN:DFN-10-1EP_2.6x2.6mm_P0.5mm_EP1.3x2.2mmU3
1SchottkyDiode_SMD:D_SOD-123D37
1TestPoint_SquarePCBPiano_Footprints:TestPoint_Pad_1.0x1.0mmTP25
1USB C Sink Ctrl/Batt ChgrPCBPiano_Footprints:QFN-22_2.5x3.2mm_P0.4mmU13
1USB4110-GF-APCBPiano_Footprints:USB_C_Receptacle_GCT_USB4110J1
1micro SD Card SlotPCBPiano_Footprints:microSD_HC_Hirose_DM3D-SFJ6

More from ninjatill/PCB-Capacitive-Touch-Synth

2
  • 2 layers280 × 110 mmPCB Piano v1.0, the printed circuit board in 3D

    PCB Piano v1.0

    ninjatill/PCB-Capacitive-Touch-Synth

    A Raspberry Pi-based synthesizer with capacitive touch keys directly on a PCB.

    267 parts
  • 2 layers20.5 × 25.4 mmDebug Breakout, the printed circuit board in 3D

    Debug Breakout

    ninjatill/PCB-Capacitive-Touch-Synth

    A Raspberry Pi-based synthesizer with capacitive touch keys directly on a PCB.

    3 parts

Similar boards

  • 2 layers100 × 100 mmSensorMicrocontroller, the printed circuit board in 3D

    SensorMicrocontroller

    WheelchairSeniorDesign/PCBs

    The PCB designs for the wheelchair for our senior design project

    39 parts1
  • 2 layers100 × 74 mmMicromouse, the printed circuit board in 3D

    Micromouse

    kbumsik/WolfieMouse

    IEEE Reion 1 Micromouse competition.

    214 parts79
  • 4 layers76 × 100 mmChlorine revD, the printed circuit board in 3D

    Chlorine revD

    kanengomibako/Chlorine

    206 parts11Unlicense
  • 2 layers195 × 148.5 mmSpecAnFrontEnd, the printed circuit board in 3D

    SpecAnFrontEnd

    richardhosking/Spectrum-analyser-Front-End-KICAD

    PCB/Schematic files

    151 parts2
  • 2 layersOldSpecAnFrontEnd, the printed circuit board in 3D

    OldSpecAnFrontEnd

    richardhosking/KicadSpecAnalayser-

    KICAD Files for Spectrum Analyser design

    156 parts1
  • 4 layers77.9 × 81.6 mmLilygo, the printed circuit board in 3D

    Lilygo

    Ndambia/lilygo

    A custom 4-layer KiCad PCB design integrating an ESP32 Wi-Fi/Bluetooth microcontroller with a SIM7600G-H 4G LTE Cat-4 cellular module, comprehensive power management, GPS tracking, GPRS connectivity, USB-C charging…

    188 parts
  • 8 layers136.9 × 155.9 mmRA8M1, the printed circuit board in 3D

    RA8M1

    pickplace-de/hexagon

    243 parts

Questions

How big is the PCB Piano v1.1 PCB?

It measures 280 × 110 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PCB Piano v1.1 use?

284 parts, built around the RP2040, 74AHCT2G125DP, PCA9685BS and MTCH2120-V/REB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PCB Piano v1.1 KiCad files?

From the ninjatill/PCB-Capacitive-Touch-Synth repository on GitHub, at the commit this page was made from: the board is hardware/PCB Piano v1.1/PCB Piano v1.1.kicad_pcb and its schematic hardware/Debug Breakout/Debug Breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PCB Piano v1.1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask ninjatill before reusing the design.