Skip to the content
12345678

THVD1406D

Texas InstrumentsExtended

-40℃~+125℃ 1 1 1.7mA 256 3V~5.5V 500Kbps Enable shutdown、Automatic direction control Half-Duplex Transceiver ±16kV SOIC-8 RS-485 / RS-422 ICs ROHS

Part id
ti/THVD1406D
Category
RS 485, RS 422 ICs
Package
SOIC-8
Pins
8
In stock
5,682 at JLCPCB (C5215918)
Used on
4 open-source boards

Overview

The THVD1406D is a RS 485, RS 422 IC made by Texas Instruments in a SOIC-8 package with 8 pins. -40℃~+125℃ 1 1 1.7mA 256 3V~5.5V 500Kbps Enable shutdown、Automatic direction control Half-Duplex Transceiver ±16kV SOIC-8 RS-485 / RS-422 ICs ROHS.

PCBKit's library has its KiCad symbol (Analog & Interface:THVD1406, from CERN's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 5,682 are in stock at JLCPCB (part C5215918). 4 open-source boards in 3 repositories on GitHub use it.

Symbol

2RE1R3SHDN4D8VCC6A7B5GND
Analog & Interface:THVD1406From CERN's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

13
Supply, least
3 V · VCC, recommended operating min · p. 4
Supply, most
5.5 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
7 V · VCC, absolute max · p. 4
Works from
-40 °C · TA, operating ambient min · p. 4
Works up to
125 °C · TA, operating ambient max · p. 4
Junction, hottest
170 °C · TJ, absolute max · p. 4
Takes working
1.7 mA · VCC = 5.5 V, driver and receiver enabled, unloaded, typical · p. 6
Takes asleep
3 µA · VCC = 5.5 V, SHDN = 0, unloaded, typical · p. 6
A pin gives at most
24 mA · Receiver output current, absolute max · p. 4
Data rate, most
500 kbit/s · THVD1406 signaling rate max · p. 4
Junction to air (D (SOIC))
126 K/W · Junction to ambient · p. 5
Junction to case (D (SOIC))
66.2 K/W · Junction to case, top · p. 5
Junction to board (D (SOIC))
69.4 K/W · Junction to board · p. 5

What it is and has

6
Interface
Half-duplex RS-422/RS-485 · p. 1
Direction control
Automatic, using the data input pin · p. 1
Data rate
500kbps · p. 1
Bus fault protection
±16V · p. 1
Fail-safe
Open, shorted and idle bus · p. 1
Bus loading
1/8 unit load, up to 256 bus nodes · p. 1

Specifications

57
ParameterConditionsAs printedPage
电源电压 VCCmin -0.5 · max 7 V4
任何逻辑引脚(D、SHDN 或 RE)上的输入电压 VLmin -0.3 · max 5.7 V4
A 或 B 输入上的电压范围 VA、VBmin -16 · max 16 V4
接收器输出电流 IOmin -24 · max 24 mA4
结温 TJmax 170 °C4
存储温度 TSTGmin -65 · max 150 °C4
静电放电 V(ESD)人体放电模型(HBM),符合 ANSI/ESDA/JEDEC JS-001;总线端子(A、B)和 GND 之间min -16000 · max 16000 V4
静电放电 V(ESD)人体放电模型(HBM);所有其他引脚min -4000 · max 4000 V4
静电放电 V(ESD)充电器件模型 (CDM),符合 ANSI/ESDA/JEDEC JS-002min -1500 · max 1500 V4
静电放电 V(ESD)IEC 61000-4-2 ESD(接触放电),总线端子和接地 (GND)min -12000 · max 12000 V4
静电放电 V(ESD)IEC 61000-4-2 ESD(空气间隙放电),总线端子和接地 (GND)min -15000 · max 15000 V4
静电放电 V(ESD)IEC 61000-4-4 EFT (快速瞬变或突发)、总线端子和 GNDmin -4000 · max 4000 V4
电源电压 VCC标称值列为 5 Vmin 3 · typ 5 · max 5.5 V4
差分输入电压 VIDmin -12 · max 12 V4
任何总线端子上的输入电压 VImin -7 · max 12 V4
高电平输入电压(D、SHDN 和 RE 输入) VIHmin 2 · max 5.5 V4
低电平输入电压(D、SHDN 和 RE 输入) VILmin 0 · max 0.8 V4
输出电流 IO驱动器min -60 · max 60 mA4
输出电流 IO接收器min -8 · max 8 mA4
差分负载电阻 RL标称值列为 60 Ωmin 54 · typ 60 Ω4
信令速率:THVD1406 1/tUITHVD1406max 500 kbps4
结温 TJmin -40 · max 150 °C4
工作环境温度 TAmin -40 · max 125 °C4
热关断阈值(温度上升) TSHDNmin 150 · typ 170 °C4
热关断迟滞 THYStyp 15 °C4
结至环境热阻 RθJATHVD1406, D (SOIC), 8 引脚typ 126 °C/W5
结至外壳(顶部)热阻 RθJC(top)THVD1406, D (SOIC), 8 引脚typ 66.2 °C/W5
结至电路板热阻 RθJBTHVD1406, D (SOIC), 8 引脚typ 69.4 °C/W5
结至顶部特征参数 ψJTTHVD1406, D (SOIC), 8 引脚typ 18.7 °C/W5
结至电路板特征参数 ψJBTHVD1406, D (SOIC), 8 引脚typ 68.7 °C/W5
功率耗散 PDTHVD1406, 500kbps, 未端接, RL = 300Ω、CL = 50pF;驱动器和接收器已启用、VCC = 5.5V、TA = 125°C、50% 方波占空比和最大信号传输速率;表列值typ 150 mW5
功率耗散 PDTHVD1406, 500kbps, RS-422 负载, RL = 100Ω、CL = 50pF;驱动器和接收器已启用、VCC = 5.5V、TA = 125°C、50% 方波占空比和最大信号传输速率;表列值typ 175 mW5
功率耗散 PDTHVD1406, 500kbps, RS-485 负载, RL = 54Ω、CL = 50pF;驱动器和接收器已启用、VCC = 5.5V、TA = 125°C、50% 方波占空比和最大信号传输速率;表列值typ 220 mW5
驱动器差分输出电压幅度 │VOD│RL = 60Ω、–7V ≤ Vtest ≤ 12V;参阅图 7-1min 1.5 · typ 2 V6
驱动器差分输出电压幅度 │VOD│RL = 60Ω、–7V ≤ Vtest ≤ 12V、4.5V ≤ Vcc ≤ 5.5V;参阅图 7-1min 2.1 · typ 3 V6
驱动器差分输出电压幅度 │VOD│RL = 100Ω,CL = 50pF;参阅图 7-2min 2 · typ 2.5 V6
驱动器差分输出电压幅度 │VOD│RL = 54 Ω,CL = 50 pF;参阅图 7-2min 1.5 · typ 2 V6
驱动器差分输出电压幅度 │VOD│RL = 54Ω、4.5V ≤ Vcc ≤ 5.5V;参阅图 7-2min 2.1 · typ 3 V6
驱动器差分输出电压幅度的改变 Δ│VOD│RL = 54Ω 或 100Ω、CL = 50pF;参阅图 7-2min -50 · max 50 mV6
稳定状态共模输出电压 VOC(SS)RL = 54Ω 或 100Ω、CL = 50pF;参阅图 7-2;典型值为 VCC/2min 1 · max 3 V6
差分驱动器共模输出电压的变化 ΔVOCRL = 54Ω 或 100Ω、CL = 50pF;参阅图 7-2min -50 · max 50 mV6
峰值到峰值驱动器共模输出电压 VOC(PP)RL = 54Ω 或 100Ω、CL = 50pF、VCC = 3.3V;参阅图 7-2typ 200 mV6
驱动器短路输出电流 │IOS│–7V ≤ [VA 或 VB] ≤ 12V、或 A 引脚短接至 B 引脚min -250 · max 250 mA6
总线输入电流(驱动器已禁用) IIVCC = 0V 或 5.5V;VI = 12 Vtyp 75 · max 100 uA6
总线输入电流(驱动器已禁用) IIVCC = 0V 或 5.5V;VI = –7 Vmin -97 · typ -70 uA6
正向接收器差分输入电压阈值 VIT+-7 V ≤ VCM ≤ 12 Vtyp -70 · max -45 mV6
负向接收器差分输入电压阈值 VIT–-7 V ≤ VCM ≤ 12 Vmin -200 · typ -150 mV6
接收器差分输入电压阈值迟滞 (VIT+ – VIT–) VHYS-7 V ≤ VCM ≤ 12 Vmin 30 · typ 50 mV6
接收器低电平输出电压 VOLIOL=4mAtyp 0.2 · max 0.4 V6
接收器高阻抗输出电流 IOZVO = 0V 或 VCC、RE = VCCmin -1 · max 1 uA6
输入电流(D、SHDN、RE) IINmin -5 · max 5 uA6
电源电流(静态) ICCVCC = 3.6 V;驱动器和接收器已启用;SHDN = VCC、RE = 0、D = 0,空载typ 1500 · max 1800 uA6
电源电流(静态) ICCVCC = 3.6 V;驱动器被启用,接收器被禁用;SHDN = VCC、RE = VCC、D = 0,空载typ 1000 · max 1500 uA6
电源电流(静态) ICCVCC = 3.6 V;驱动器和接收器被禁用;SHDN = 0,空载typ 2 · max 4.1 uA6
电源电流(静态) ICCVCC = 5.5 V;驱动器和接收器已启用;SHDN = VCC、RE = 0、D = 0,空载typ 1700 · max 3000 uA6
电源电流(静态) ICCVCC = 5.5 V;驱动器被启用,接收器被禁用;SHDN = VCC、RE = VCC、D = 0,空载typ 1300 · max 2500 uA6
电源电流(静态) ICCVCC = 5.5 V;驱动器和接收器被禁用;SHDN = 0,空载typ 3 · max 6.9 uA6

Ordering codes, by the datasheet

2
THVD1406DR
SOIC (D) | 8 · 3000 | LARGE T&R; NIPDAU; -40 to 125 °C · p. 22
THVD1406DR.A
SOIC (D) | 8 · 3000 | LARGE T&R; NIPDAU; -40 to 125 °C · p. 22

Open-source boards using it

4
  • 2 layers79.2 × 68.8 mmEnvironment slave, the printed circuit board in 3D

    Environment slave

    pcbcupid/Lora-Wireless-Sensor-Network

    A wireless sensor network based on Lora and esp32C3. This repo will help you build a complete product from scratch to finish!

    72 parts30MIT
  • 2 layers100 × 100 mmKijaniCarrier, the printed circuit board in 3D

    KijaniCarrier

    Waziup/WaziDev

    WaziDev official repository

    75 parts5Apache-2.0
  • 4 layers84 × 55 mmGrblPANEL, the printed circuit board in 3D

    GrblPANEL

    dresco/grblpanel_main_board

    KiCad implementation of a grblPANEL control board

    143 parts2
  • 2 layers53.8 × 62.9 mmEnvironmental monitoring device, the printed circuit board in 3D

    Environmental monitoring device

    pcbcupid/Lora-Wireless-Sensor-Network

    A wireless sensor network based on Lora and esp32C3. This repo will help you build a complete product from scratch to finish!

    43 parts30MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the THVD1406D?

Yes. The symbol is Analog & Interface:THVD1406 and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the THVD1406D?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the THVD1406D datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the THVD1406D?

JLCPCB lists it as part C5215918, with 5,682 in stock; the sellers' links on this page open their listings.

What can replace the THVD1406D?

Parts like it in the library: the SP3485EN-L/TR by MaxLinear, the SP485EEN-L/TR by MaxLinear, the SN75176BD by Texas Instruments and the MAX485ESA+T by Maxim Integrated (Analog Devices). Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the THVD1406D?

4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.