OPA1656ID

Texas Instruments

-18V~-2.25V、2.25V~18V -40℃~+125℃ 100mA 120dB 1mV 2 20pA 20pA 24V/us 2uV/℃ 3.9mA 4.3nV/√Hz@1kHz 4.5V~36V 53MHz Rail-to-rail output SOIC-8 FET Input Amplifiers ROHS

Extended

Datasheetti/OPA1656ID

Category: Audio Amplifiers
Package: SOIC-8
Pins: 8

Overview

The OPA1656ID is an audio Amplifier made by Texas Instruments in a SOIC-8 package with 8 pins. -18V~-2.25V、2.25V~18V -40℃~+125℃ 100mA 120dB 1mV 2 20pA 20pA 24V/us 2uV/℃ 3.9mA 4.3nV/√Hz@1kHz 4.5V~36V 53MHz Rail-to-rail output SOIC-8 FET Input Amplifiers ROHS.

PCBKit's library has its KiCad symbol (Amplifier_Operational:OPA1656ID, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 1,814 are in stock at JLCPCB (part C1849431). 52 open-source boards in 25 repositories on GitHub use it.

Symbol

Amplifier_Operational:OPA1656IDFrom KiCad's library

Footprint

Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

Supply, least: 4.5 V · V+, single supply, recommended minimum relative to V– · p. 4
Supply, most: 36 V · V+, single supply, recommended maximum relative to V– · p. 4
Supply, least: 2.25 V · V+/V–, dual supply, recommended minimum rail magnitude · p. 4
Supply, most: 18 V · V+/V–, dual supply, recommended maximum rail magnitude · p. 4
Supply, absolute maximum: 40 V · V+ minus V–, absolute maximum · p. 4
Works from: -40 °C · Operating free-air temperature, recommended minimum · p. 4
Works up to: 125 °C · Operating free-air temperature, recommended maximum · p. 4
Junction, hottest: 150 °C · Junction temperature, absolute maximum · p. 4
Takes working: 7.8 mA · sum of two channels' typical quiescent current, IO = 0 A · p. 7
Takes at most: 10 mA · sum of two channels' maximum quiescent current, –40°C to +125°C · p. 7
Junction to air (D (SOIC)): 119.9 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to case (D (SOIC)): 51.8 K/W · Junction-to-case (top) thermal resistance · p. 5
Junction to board (D (SOIC)): 65.4 K/W · Junction-to-board thermal resistance · p. 5

What it is and has

Channels and package: Dual, D (SOIC, 8) · p. 1
Voltage noise: 2.9 nV/√Hz at 10 kHz · p. 1
Current noise: 6 fA/√Hz at 1 kHz · p. 1
Open-loop gain: 150 dB · p. 1
Output current: 100 mA · p. 1
Input bias current: 10 pA · p. 1
Slew rate: 24 V/μs · p. 1
Gain bandwidth product: 53 MHz · p. 1
Output swing: Rail-to-rail output · p. 1
Quiescent current: 3.9 mA per channel · p. 1
Protection: Internal phase-reversal protection · p. 15

Around it

cap 0.1 µF: between V+ and ground; Low-ESR ceramic bypass capacitor, placed as close to the device as possible. · p. 27

Specifications

Parameter	Conditions	As printed	Page
Supply voltage, VS = (V+) – (V–) VS	Over operating free-air temperature range	max 40 V	4
Input (all pins except power-supply pins)	Current; over operating free-air temperature range	min -10 · max 10 mA	4
Operating, TA TA	Temperature	min -55 · max 125 °C	4
Junction, TJ TJ	Temperature	max 150 °C	4
Storage, Tstg Tstg	Temperature	min -65 · max 150 °C	4
Supply voltage VS	Single supply; over operating free-air temperature range	min 4.5 · max 36 V	4
Operating temperature TA	Free-air temperature	min -40 · max 125 °C	4
Junction-to-ambient thermal resistance RθJA	OPA1656, D (SOIC), 8 PINS	typ 119.9 °C/W	5
Junction-to-case (top) thermal resistance RθJC(top)	OPA1656, D (SOIC), 8 PINS	typ 51.8 °C/W	5
Junction-to-board thermal resistance RθJB	OPA1656, D (SOIC), 8 PINS	typ 65.4 °C/W	5
Junction-to-top characterization parameter ψJT	OPA1656, D (SOIC), 8 PINS	typ 10 °C/W	5
Junction-to-board characterization parameter ψJB	OPA1656, D (SOIC), 8 PINS	typ 64.2 °C/W	5
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 600 Ω, VO = 3.5 VRMS, f = 1 kHz, 80-kHz measurement bandwidth	typ 0.000029 %	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 600 Ω, VO = 3.5 VRMS, f = 1 kHz, 80-kHz measurement bandwidth	typ -131 dB	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 600 Ω, VO = 3.5 VRMS, f = 20 kHz, 80-kHz measurement bandwidth	typ 0.0001 %	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 600 Ω, VO = 3.5 VRMS, f = 20 kHz, 80-kHz measurement bandwidth	typ -120 dB	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 2 kΩ, VO = 3.5 VRMS, f = 1 kHz, 80-kHz measurement bandwidth	typ 0.000029 %	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 2 kΩ, VO = 3.5 VRMS, f = 1 kHz, 80-kHz measurement bandwidth	typ -131 dB	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 2 kΩ, VO = 3.5 VRMS, f = 20 kHz, 80-kHz measurement bandwidth	typ 0.000035 %	6
Total harmonic distortion + noise THD+N	TA = 25°C, VS = ±18 V; G = 1, RL = 2 kΩ, VO = 3.5 VRMS, f = 20 kHz, 80-kHz measurement bandwidth	typ -129 dB	6
Intermodulation distortion IMD	TA = 25°C, VS = ±18 V, RL = 2 kΩ; G = 1, VO = 3.5 VRMS, SMPTE/DIN two-tone, 4:1 (60 Hz and 7 kHz)	typ 0.000018 %	6
Intermodulation distortion IMD	TA = 25°C, VS = ±18 V, RL = 2 kΩ; G = 1, VO = 3.5 VRMS, SMPTE/DIN two-tone, 4:1 (60 Hz and 7 kHz)	typ -135 dB	6
Intermodulation distortion IMD	TA = 25°C, VS = ±18 V, RL = 2 kΩ; G = 1, VO = 3.5 VRMS, CCIF twin-tone (19 kHz and 20 kHz)	typ 0.00002 %	6
Intermodulation distortion IMD	TA = 25°C, VS = ±18 V, RL = 2 kΩ; G = 1, VO = 3.5 VRMS, CCIF twin-tone (19 kHz and 20 kHz)	typ -134 dB	6
Gain-bandwidth product GBW	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; G = 100	typ 53 MHz	6
Unity gain bandwidth GBW	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; G = 1	typ 20 MHz	6
Slew rate SR	TA = 25°C, VS = ±18 V, RL = 2 kΩ; G = –1, 10-V step	typ 24 V/us	6
Full-power bandwidth(1)	TA = 25°C, VS = ±18 V, RL = 2 kΩ; VO = 1 VP	typ 3.8 MHz	6
Overload recovery time	TA = 25°C, VS = ±18 V, RL = 2 kΩ; G = –10	typ 100 ns	6
Channel separation	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 1 kHz	typ -135 dB	6
Settling time	TA = 25°C, VS = ±18 V, RL = 2 kΩ; 0.01%, G = –1, 10-V step	typ 800 ns	6
Input voltage noise	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 20 Hz to 20 kHz	typ 0.53 uVRMS	6
Input voltage noise	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 0.1 Hz to 10 Hz	typ 1.9 uVPP	6
Input voltage noise density en	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 100 Hz	typ 11.8 nV/√Hz	6
Input voltage noise density en	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 1 kHz	typ 4.3 nV/√Hz	6
Input voltage noise density en	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 10 kHz	typ 2.9 nV/√Hz	6
Input current noise density in	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 1 kHz	typ 6 fA/√Hz	6
Input offset voltage drift(2) dVOS/dT	VS = ±2.25 V to ±18 V, TA = –40°C to +125°C, RL = 2 kΩ, VCM = VOUT = VS/2	typ 0.3 · max 2 uV/°C	6
Power-supply rejection ratio PSRR	TA = 25°C, RL = 2 kΩ, VCM = VOUT = VS/2; VS = ±2.25 V to ±18 V	typ 0.3 · max 5 uV/V	6
Common-mode rejection ratio CMRR	TA = 25°C, VS = ±18 V, RL = 2 kΩ; (V–) ≤ VCM ≤ (V+) – 2.25	min 106 · typ 120 dB	6
Open-loop voltage gain AOL	TA = 25°C, VS = ±18 V; (V–) + 1.3 V ≤ VO ≤ (V+) – 1.3 V, RL = 600 Ω	min 134 · typ 150 dB	6
Open-loop voltage gain AOL	TA = 25°C, VS = ±18 V; (V–) + 0.5 V ≤ VO ≤ (V+) – 0.5 V, RL = 2 kΩ	min 134 · typ 154 dB	6
Open-loop output impedance ZO	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; f = 1 MHz	typ 26 Ω	7
Capacitive load drive CL	TA = 25°C, VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2	typ 100 pF	7
Quiescent current (per channel) IQ	TA = 25°C, RL = 2 kΩ, VCM = VOUT = VS/2; IO = 0 A, VS = ±2.25 V to ±18 V	typ 3.9 · max 4.6 mA	7
Quiescent current (per channel) IQ	VS = ±18 V, RL = 2 kΩ, VCM = VOUT = VS/2; IO = 0 A, TA = –40°C to +125°C(2)	max 5 mA	7

Pins, by the datasheet

1 OUT A: Output, channel A · p. 3
2 –IN A: Inverting input, channel A · p. 3
3 +IN A: Noninverting input, channel A · p. 3
4 V–: Negative (lowest) power supply · p. 3
5 +IN B: Noninverting input, channel B · p. 3
6 –IN B: Inverting input, channel B · p. 3
7 OUT B: Output, channel B · p. 3
8 V+: Positive (highest) power supply · p. 3

Ordering codes, by the datasheet

OPA1656ID: SOIC (D) · 8 pins; 75 units, tube; operating temperature -40 to 125 °C · p. 31
OPA1656ID.B: SOIC (D) · 8 pins; 75 units, tube; operating temperature -40 to 125 °C · p. 31
OPA1656IDR: SOIC (D) · 8 pins; 2500 units, large tape and reel; operating temperature -40 to 125 °C · p. 31
OPA1656IDR.B: SOIC (D) · 8 pins; 2500 units, large tape and reel; operating temperature -40 to 125 °C · p. 31
OPA1656IDRG4: SOIC (D) · 8 pins; 2500 units, large tape and reel; operating temperature -40 to 125 °C · p. 31
OPA1656IDRG4.B: SOIC (D) · 8 pins; 2500 units, large tape and reel; operating temperature -40 to 125 °C · p. 31

Parameters

Common Mode Rejection Ratio(CMRR): 120dB
Current - Supply: 7.8mA
Current - Supply(Max): 10mA
Dual Supply: -18V~-2.25V
Gain Bandwidth Product: 53MHz
Ib - Input Bias Current: 20pA
Input Offset Current(Ios): 20pA
Input Offset Voltage Drift(Vos TC): 2uV/℃
Junction Temperature(Max): 150℃
Noise density(eN): 4.3nV/√Hz@1kHz
Number of Channels: 2
Operating Temperature: -40℃~+125℃
Output Current: 100mA
Quiescent Current(Iq): 3.9mA
Rail To Rail: Rail-to-rail output
Single Supply: 4.5V~36V
Slew Rate: 24V/us
Thermal Resistance(Junction to Ambient): 119.9℃/W
Thermal Resistance(Junction to Board): 65.4℃/W
Thermal Resistance(Junction to Case): 51.8℃/W
Voltage - Supply: 2.25V~36V
Voltage - Supply(Absolute Max): 40V
Vos - Input Offset Voltage: 1mV

Order codes

OPA1656IDLCSC C1346368
OPA1656IDRLCSC C1849431

Pinout

The pins of the OPA1656ID
Pin	Name	Type
1	—	Output
2	-	Input
3	+	Input
4	V-	Power in
5	+	Input
6	-	Input
7	—	Output
8	V+	Power in

Open-source boards using it

All 52

4 layers241.7 × 56.7 mm
Daisy studio
squeedee/daisy-studio
Daisy Seed Carrier for Balanced Pro Audio
141 parts14MIT
2 layers148.3 × 108.4 mm
RJ Schematic v1.0
Jscott44/RTEP5-the-raspberry-jam
Realtime digital guitar effects pedal designed for Raspberry PI, written in C++
121 parts13MIT
2 layers32 × 68.5 mm
Rectifier
AKJUS/1590A
Random odd guitar pedal design in kicad
49 parts3GPL-2.0
4 layers66 × 46 mm
Radar1
HearnChristian/k-band-fmcw-radar
24 GHz FMCW radar front-end in KiCad (WIP): ADF4159 chirp synth, BGT24LTR11 transceiver, custom Marki AMM-8211PSM driver-amp symbol/footprint, OPA1656 IF, ADS8353 ADC, FT2232H USB.
99 parts3
4 layers260 × 110 mm
Pandore
filliformes/pandore
pandore is an open-source digital audio instrument protyping platform based on the LattePanda Mu.
804 parts2
6 layers150 × 63 mm
Native refill export
AxelMcKenna/AFX-1000
RMX-1000-inspired effects processor for macOS, AU and VST3, built on a shared C++20 engine. Standalone Daisy Seed 3 hardware with two main PCBs and a custom housing is in development.
334 parts1
4 layers154 × 81 mm
System candidate
bernardopg/ps28-modern-amp
Infinity Primus PS28 amplifier modernization: TPA3255 engineering, validation and safety-gated workflow
269 parts1
4 layers100 × 100 mm
Pcb AMY
Rivercraft911/R-01_Raster_Laser_Projector
Red, blue and green lasers combine through two dichroc mirrors and bounce off a spinning polygon mirror, which each mirror facet makes one scanline.
159 parts1

Show this part on your page

A live frame, for any web page

<iframe src="https://pcbkit.io/embed/parts/ti/OPA1656ID" title="OPA1656ID in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>

A picture

<img src="https://pcbkit.io/embed/parts/ti/OPA1656ID.jpg" alt="OPA1656ID" width="1200" height="900">

A picture that opens the part, for a README

[![OPA1656ID](https://pcbkit.io/embed/parts/ti/OPA1656ID.jpg?size=s)](https://pcbkit.io/parts/ti/OPA1656ID)

Questions

Is there a KiCad symbol and footprint for the OPA1656ID?

Yes. The symbol is Amplifier_Operational:OPA1656ID and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the OPA1656ID?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the OPA1656ID datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the OPA1656ID?

JLCPCB lists it as part C1849431, with 1,814 in stock; the sellers' links on this page open their listings.

What can replace the OPA1656ID?

Parts like it in the library: the OPA2613ID by Texas Instruments, the TC8002D by FM, the LM833D by onsemi and the LM4871MX by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the OPA1656ID?

52 boards in 25 repositories on GitHub; the most starred are listed on this page, with their KiCad files.

OPA1656ID

Overview

Symbol

Footprint

From the datasheet

What it is and has

Around it

Specifications

Pins, by the datasheet

Ordering codes, by the datasheet

Parameters

Order codes

Pinout

Open-source boards using it

Daisy studio

RJ Schematic v1.0

Rectifier

Radar1

Pandore

Native refill export

System candidate

Pcb AMY

Show this part on your page

Questions

Is there a KiCad symbol and footprint for the OPA1656ID?

What package is the OPA1656ID?

Where is the OPA1656ID datasheet?

Where can I order the OPA1656ID?

What can replace the OPA1656ID?

Which open-source boards use the OPA1656ID?

Parts like it

OPA2613ID

TC8002D

LM833D

LM4871MX

FM8002E

OPA1612AID

OPA1642AID

LM4808MX