Skip to the content
12345678

OPA1612AID

Texas InstrumentsExtended

-2.25V~18V -40℃~+85℃ 0.000015% 2 Pairs Differential Inputs 2-Channel 3.6mA ESD protection SOIC-8 Audio Amplifiers ROHS

Part id
ti/OPA1612AID
Category
Audio Amplifiers
Package
SOIC-8
Pins
8
In stock
21,767 at JLCPCB (C94590)
Used on
29 open-source boards

Overview

The OPA1612AID is an audio Amplifier made by Texas Instruments in a SOIC-8 package with 8 pins. -2.25V~18V -40℃~+85℃ 0.000015% 2 Pairs Differential Inputs 2-Channel 3.6mA ESD protection SOIC-8 Audio Amplifiers ROHS.

PCBKit's library has its KiCad symbol (Amplifier_Operational:OPA1612AxD, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 21,767 are in stock at JLCPCB (part C94590). 29 open-source boards in 14 repositories on GitHub use it.

Symbol

12-3+
Amplifier_Operational:OPA1612AxDFrom KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

8
Supply, least
4.5 V · V+ – V–, recommended operating minimum · p. 4
Supply, most
36 V · V+ – V–, recommended operating maximum · p. 4
Supply, absolute maximum
40 V · V+ – V–, absolute maximum · p. 4
Works from
-55 °C · Operating ambient temperature minimum · p. 4
Works up to
125 °C · Operating ambient temperature maximum · p. 4
Junction, hottest
200 °C · Junction temperature absolute maximum · p. 4
Takes working
7.2 mA · sum of two channels' typical quiescent currents, IOUT = 0 A · p. 6
Junction to air (SOIC-8)
150 K/W · Junction-to-ambient thermal resistance, typical · p. 6

What it is and has

4
Input architecture
Bipolar-input audio operational amplifier · p. 1
Output
Rail-to-rail · p. 1
Gain stability
Unity-gain stable · p. 12
Amplifier channels
2 (dual) · p. 1

Around it

2
cap 0.1 μF
between V+ and GND; Bypass capacitor close to the positive power-supply pin. · p. 19
res 50 Ω
between OUT and capacitive load; Example series isolation resistor for heavier capacitive loads; applies to either channel. · p. 17

Specifications

18
ParameterConditionsAs printedPage
Supply voltage VSVS = (V+) – (V–); over operating free-air temperature rangemax 40 V4
Operating temperature TAmin -55 · max 125 °C4
Junction temperature TJmax 200 °C4
Storage temperature range Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pinsmin -3000 · max 3000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pinsmin -1000 · max 1000 V4
Electrostatic discharge V(ESD)Machine model (MM)min -200 · max 200 V4
Supply voltage (V+ – V–)Over operating free-air temperature range; total supply voltagemin 4.5 · max 36 V4
Specified temperaturemin -40 · max 85 °C4
Open-loop voltage gain AOLTA = +25°C; VCM = VOUT = midsupply; (V–) + 0.2 V ≤ VO ≤ (V+) – 0.2 V, RL = 10 kΩmin 114 · typ 130 dB6
Open-loop voltage gain AOLTA = +25°C; VCM = VOUT = midsupply; (V–) + 0.6 V ≤ VO ≤ (V+) – 0.6 V, RL = 2 kΩmin 110 · typ 114 dB6
Short-circuit current ISCTA = +25°C; positive currenttyp 55 mA6
Short-circuit current ISCTA = +25°C; negative currenttyp -62 mA6
Quiescent current (per channel) IQTA = +25°C; IOUT = 0 Atyp 3.6 · max 4.5 mA6
IQ over Temperature IQPer channel; IOUT = 0 A; TA = –40°C to +85°C; specified by design and characterizationmax 5.5 mA6
Specified rangemin -40 · max 85 °C6
Operating rangemin -55 · max 125 °C6
Thermal resistance, SOIC-8 θ JASOIC-8typ 150 °C/W6

Pins, by the datasheet

8
1 OUT A
Output, channel A. · p. 3
2 –IN A
Inverting input, channel A. · p. 3
3 +IN A
Noninverting input, channel A. · p. 3
4 V–
Negative (lowest) power supply. · p. 3
5 +IN B
Noninverting input, channel B. · p. 3
6 –IN B
Inverting input, channel B. · p. 3
7 OUT B
Output, channel B. · p. 3
8 V+
Positive (highest) power supply. · p. 3

Open-source boards using it

29See all 29
  • 4 layers75 × 36 mmEmoeNAP, the printed circuit board in 3D

    EmoeNAP

    Floyd-Fish/Noise-Amplifier

    An ultra-low noise amplifier to measure low-noise LDO/OPA's wide band output noise, and many other interesting measurements. Referred to AN-159.

    189 parts36GPL-3.0
  • 2 layers31.5 × 46.7 mmEMGSensor3.1, the printed circuit board in 3D

    EMGSensor3.1

    courtcourtaney/voxEMG

    VoxEMG circuit and schematics, plus example code for further digital filtering with Bela, etc.

    123 parts12
  • 4 layers99.5 × 15 mmOPA PHONO, the printed circuit board in 3D

    OPA PHONO

    arthurbenemann/OPA_PHONO

    Phono amplifier for MM cartridges, base on TI's OPA lineup

    64 parts2GPL-3.0
  • 4 layers100 × 100 mmRadio Receiver McCormick Mendoza, the printed circuit board in 3D

    Radio Receiver McCormick Mendoza

    Jeffrey-McCormick/CPTR480-ENGR357_Quadrature_SDR

    Quadrature sampling software defined radio for digital signal processing. Project for Embedded and Real Time Systems (CPTR480) and Engineering Electronics II (ENGR357).

    244 parts2MIT
  • 2 layers100 × 80 mmSteDAC, the printed circuit board in 3D

    SteDAC

    stefantquach/steDAC

    Open source audio DAC project based on the ES9038Q2M DAC from ESS. Still WIP

    164 parts2
  • 6 layers150 × 63 mmNative refill export, the printed circuit board in 3D

    Native refill export

    AxelMcKenna/AFX-1000

    RMX-1000-inspired effects processor for macOS, AU and VST3, built on a shared C++20 engine. Standalone Daisy Seed 3 hardware with two main PCBs and a custom housing is in development.

    334 parts1
  • 4 layers161 × 100 mmAD DA module, the printed circuit board in 3D

    AD DA module

    KLFAMO/relock_Artiq

    This project is an electronic device based on the STM32 microcontroller, equipped with an Ethernet port for remote control and data communication.

    416 parts
  • 2 layers73.9 × 56 mmRaspberrypi gpio audio, the printed circuit board in 3D

    Raspberrypi gpio audio

    pasdesignal-zz/rPI_audio_board

    a rPi daughter board for audio io and midi

    117 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the OPA1612AID?

Yes. The symbol is Amplifier_Operational:OPA1612AxD and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the OPA1612AID?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the OPA1612AID datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the OPA1612AID?

JLCPCB lists it as part C94590, with 21,767 in stock; the sellers' links on this page open their listings.

What can replace the OPA1612AID?

Parts like it in the library: the TC8002D by FM, the LM833D by onsemi, the LM4871MX by Texas Instruments and the FM8002E by Shenzhen Fuman Elec. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the OPA1612AID?

29 boards in 14 repositories on GitHub; the most starred are listed on this page, with their KiCad files.