
MCP6022-I/P
Microchip TechnologyExtended
-40℃~+125℃ 10MHz 1mA 1pA 1pA 2 2.5V~5.5V 3.5uV/℃ 30mA 500uV 7V/us 8.7nV/√Hz@10kHz 90dB Built-in compensation Rail-to-Rail Input, Rail-to-Rail Output PDIP-8 Operational Amplifier ROHS
- Part id
- microchip/MCP6022-I/P
- Category
- Operational Amplifier
- Package
- PDIP-8
- Pins
- 8
- In stock
- 17 at JLCPCB (C640399)
- Used on
- 49 open-source boards
Overview
The MCP6022-I/P is an operational Amplifier made by Microchip Technology in a PDIP-8 package with 8 pins. -40℃~+125℃ 10MHz 1mA 1pA 1pA 2 2.5V~5.5V 3.5uV/℃ 30mA 500uV 7V/us 8.7nV/√Hz@10kHz 90dB Built-in compensation Rail-to-Rail Input, Rail-to-Rail Output PDIP-8 Operational Amplifier ROHS.
PCBKit's library has its KiCad symbol (Amplifier_Operational:MCP6022, from KiCad's library) and its footprint (Package_DIP:DIP-8_W8.89mm_SMDSocket_LongPads, from KiCad's library), ready for a KiCad board. 17 are in stock at JLCPCB (part C640399). 49 open-source boards in 37 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
9- Supply, least
- 2.5 V · VDD relative to VSS, recommended operating min · p. 3
- Supply, most
- 5.5 V · VDD relative to VSS, recommended operating max · p. 3
- Supply, absolute maximum
- 7 V · VDD – VSS, absolute max · p. 3
- Works from
- -40 °C · Industrial ambient temperature min · p. 5
- Works up to
- 85 °C · Industrial ambient temperature max · p. 5
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 3
- Takes working
- 2 mA · sum of two amplifiers' typical quiescent currents, IO = 0 · p. 3
- A pin gives at most
- 30 mA · Output and supply pins, absolute max magnitude · p. 3
- Junction to air (8L-PDIP)
- 85 K/W · Junction to ambient, typical · p. 5
What it is and has
7- Input/output range
- Rail-to-rail · p. 1
- Bandwidth
- 10 MHz typical · p. 1
- Input noise voltage density
- 8.7 nV/Hz at 10 kHz typical · p. 1
- Input offset voltage
- ±500 µV max, Industrial Temperature · p. 1
- Unity gain
- Stable · p. 1
- Amplifiers
- 2 · p. 1
- Package options
- 8-lead PDIP, SOIC, TSSOP · p. 1
Specifications
33| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VDD – VSS | max 7 V | 3 | |
| Current Analog Input Pins (VIN+, VIN-) | min -2 · max 2 mA | 3 | |
| Current at Output and Supply Pins | min -30 · max 30 mA | 3 | |
| Storage Temperature | min -65 · max 150 °C | 3 | |
| Maximum Junction Temperature | max 150 °C | 3 | |
| ESD Protection on All Pins (HBM; MM) | HBM | min 2 kV | 3 |
| ESD Protection on All Pins (HBM; MM) | MM | min 200 V | 3 |
| Input Offset Voltage: Industrial Temperature Parts VOS | VCM = 0V; Industrial Temperature Parts | min -500 · max 500 uV | 3 |
| Power Supply Rejection Ratio PSRR | VCM = 0V | min 74 · typ 90 dB | 3 |
| Input Bias Current: IB | TA = +25°C | typ 1 pA | 3 |
| Input Bias Current: Industrial Temperature Parts IB | Industrial Temperature Parts; TA = +85°C | typ 30 · max 150 pA | 3 |
| Common-Mode Rejection Ratio CMRR | VDD = 5V, VCM = -0.3V to 5.3V | min 74 · typ 90 dB | 3 |
| Common-Mode Rejection Ratio CMRR | VDD = 5V, VCM = 3.0V to 5.3V | min 70 · typ 85 dB | 3 |
| Common-Mode Rejection Ratio CMRR | VDD = 5V, VCM = -0.3V to 3.0V | min 74 · typ 90 dB | 3 |
| DC Open-Loop Gain (Large Signal) AOL | VCM = 0V, VOUT = VSS + 0.3V to VDD – 0.3V | min 90 · typ 110 dB | 3 |
| Supply Voltage VDD | min 2.5 · max 5.5 V | 3 | |
| Quiescent Current per Amplifier IQ | IO = 0 | min 0.5 · typ 1 · max 1.35 mA | 3 |
| Gain Bandwidth Product GBWP | typ 10 MHz | 4 | |
| Phase Margin PM | G = +1 V/V | typ 65 ° | 4 |
| Settling Time, 0.2% tSETTLE | G = +1 V/V, VOUT = 100 mVp-p | typ 250 ns | 4 |
| Slew Rate SR | typ 7 V/us | 4 | |
| Total Harmonic Distortion Plus Noise THD + N | f = 1 kHz, G = +1 V/V; VOUT = 0.25V to 3.25V (1.75V ± 1.50VPK), VDD = 5.0V, BW = 22 kHz | typ 0.00053 % | 4 |
| Total Harmonic Distortion Plus Noise THD + N | f = 1 kHz, G = +1 V/V, RL = 600; VOUT = 0.25V to 3.25V (1.75V ± 1.50VPK), VDD = 5.0V, BW = 22 kHz | typ 0.00064 % | 4 |
| Total Harmonic Distortion Plus Noise THD + N | f = 1 kHz, G = +1 V/V; VOUT = 4VP-P, VDD = 5.0V, BW = 22 kHz | typ 0.0014 % | 4 |
| Total Harmonic Distortion Plus Noise THD + N | f = 1 kHz, G = +10 V/V; VOUT = 4VP-P, VDD = 5.0V, BW = 22 kHz | typ 0.0009 % | 4 |
| Total Harmonic Distortion Plus Noise THD + N | f = 1 kHz, G = +100 V/V; VOUT = 4VP-P, VDD = 5.0V, BW = 22 kHz | typ 0.005 % | 4 |
| Input Noise Voltage Eni | f = 0.1 Hz to 10 Hz | typ 2.9 uVp-p | 4 |
| Input Noise Voltage Density eni | f = 10 kHz | typ 8.7 nV/Hz | 4 |
| Input Noise Current Density ini | f = 1 kHz | typ 3 fA/Hz | 4 |
| Industrial Temperature Range TA | Industrial Temperature Parts | min -40 · max 85 °C | 5 |
| Operating Temperature Range TA | Note 1: Industrial temperature devices operate over this Extended temperature range with reduced performance; TJ must not exceed +150°C. | min -40 · max 125 °C | 5 |
| Storage Temperature Range TA | min -65 · max 150 °C | 5 | |
| Thermal Resistance, 8L-PDIP JA | 8L-PDIP | typ 85 °C/W | 5 |
Pins, by the datasheet
8- 1 VOUTA
- Analog Output (Op Amp A). · p. 15
- 2 VINA-
- Inverting Input (Op Amp A). · p. 15
- 3 VINA+
- Non-Inverting Input (Op Amp A). · p. 15
- 4 VSS
- Negative Power Supply; connect to ground for a single positive supply. · p. 15
- 5 VINB+
- Non-Inverting Input (Op Amp B). · p. 15
- 6 VINB–
- Inverting Input (Op Amp B). · p. 15
- 7 VOUTB
- Analog Output (Op Amp B). · p. 15
- 8 VDD
- Positive Power Supply; requires a bypass capacitor. · p. 15
- 2 layers50.8 × 107.9 mm

- 2 layers20.3 × 110 mm

4HPico
rheslip/2HPico-Eurorack-Module-Hardware
2HP Eurorack module based on Raspberry Pi Pico 2
73 parts84 - 2 layers377.2 × 318 mm

Three phase bridge
arcoslab/open-coroco-legacy
COmpliant RObot COntroller is a free software project aiming to create an impedance controller based on a stm32 microcontroller using bldc motors and strain gauges.
105 parts6 - 2 layers58.4 × 36.8 mm

Bf-018a
botanicfields/KiCad6-Environment
My symbols, my footprints, my templates, etc. of KiCad6
22 parts5CC0-1.0 - 4 layers70 × 60 mm

Tanklevel
Th3Link/tanklevel
This project provides a solution for measuring the liquid level in tanks, such as rainwater tanks, using the TL-136 pressure sensor.
80 parts4CERN-OHL-S-2.0 - 2 layers113 × 86.7 mm

SiC based Battery Disconnect
abhinav937/SiC-Based-Bi-Directional-Circuit-breaker
KiCad 7 PCB design files for E_Fuse
138 parts2 - 2 layers43.8 × 58 mm

Pi hat
fodorbalint/OneWayLabyrinth
Program aiming to solve the one-way labyrinth generation riddle.
53 parts1 - 4 layers35 × 35 mm

Parts like it
8LM358N
DIP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 30mA 3V~36V 50nA 7mV 800uA 80dB Built-in compensation DIP-8 Operational Amplifier ROHSHGSEMIOperational AmplifierLM358N/NOPB
PDIP-8-16V~-1.5V、1.5V~16V 0℃~+70℃ 1MHz 1mA 2 2mV 3V~32V 40mA 45nA 5nA 65dB 7uV/℃ Built-in compensation PDIP-8 Operational Amplifier ROHSTexas InstrumentsOperational AmplifierNE5532P
PDIP-8-15V~15V 0℃~+70℃ 100dB 10MHz 150nA 16mA 1uA 2 38mA 4mV 5nV/√Hz@1kHz 5uV/℃ 9V/us Built-in compensation PDIP-8 Operational Amplifier ROHSTexas InstrumentsOperational AmplifierLM358N(XBLW)
DIP-8-12V~-1.5V、1.5V~12V 0℃~+70℃ 2 3V~24V 3nA 40mA 45nA 500uA 5mV 600V/ms 7uV/℃ 90dB DIP-8 Operational Amplifier ROHSXBLWOperational AmplifierUA741CP
PDIP-8-15V~15V -5V~15V 0℃~+70℃ 1 2.8mA 200nA 40mA 500V/ms 500nA 6mV 90dB Built-in compensation PDIP-8 Operational Amplifier ROHSTexas InstrumentsOperational AmplifierLM358AN
DIP-8-18V~18V -40℃~+85℃ 2 20nA 2nA 3mV 500uA 50mA 5V~36V 700V/ms 700kHz 7uV/℃ 80dB DIP-8 Operational Amplifier ROHSHGSEMIOperational AmplifierLM4558N
DIP-8-22V~22V 0℃~+70℃ 15V~22V 1MHz 2 3.5mA 30mA 500nA 5nA 6mV 90dB DIP-8 Operational Amplifier ROHSHGSEMIOperational AmplifierCA3140EZ
DIP-8-18V~18V -55℃~+125℃ 0.5pA 1 10pA 4.5MHz 40mA 40nV/√Hz@1kHz 4V~36V 4mA 5mV 8uV/℃ 90dB 9V/us Built-in compensation DIP-8 Operational Amplifier ROHSRenesas ElectronicsOperational Amplifier
Questions
Is there a KiCad symbol and footprint for the MCP6022-I/P?
Yes. The symbol is Amplifier_Operational:MCP6022 and the footprint Package_DIP:DIP-8_W8.89mm_SMDSocket_LongPads, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the MCP6022-I/P?
PDIP-8, with 8 pins. Its footprint is drawn on this page.
Where is the MCP6022-I/P datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the MCP6022-I/P?
JLCPCB lists it as part C640399, with 17 in stock; the sellers' links on this page open their listings.
What can replace the MCP6022-I/P?
Parts like it in the library: the LM358N by HGSEMI, the LM358N/NOPB by Texas Instruments, the NE5532P by Texas Instruments and the LM358N(XBLW) by XBLW. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the MCP6022-I/P?
49 boards in 37 repositories on GitHub; the most starred are listed on this page, with their KiCad files.