Skip to the content
2 layers20.3 × 110 mm4HPico, the printed circuit board in 3D

2HP Eurorack module based on Raspberry Pi Pico 2

Size
20.3 × 110 mm
Copper layers
2
Thickness
1.6 mm
Parts
73
Nets
67
Pads
229
Tracks, vias
980, 87
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
19 Dec 2025
Updated
26 Jul 2026

Overview

4HPico is an open-source printed circuit board by rheslip, from the rheslip/2HPico-Eurorack-Module-Hardware repository on GitHub. It is a 2-layer board of 20.3 × 110 mm with 73 parts on 67 nets, routed with 980 tracks and 87 vias.

It is built around the MCP6022-I/P, TL072 and AMS1117-5.0, with the 1N5819WS among its other parts. Its parts include 31 resistors, 17 capacitors, 8 ICs, 8 connectors and 2 diodes. It belongs with the RP2350 boards of this library.

Main components

4

README

README.md

2HPico-Eurorack-Module-Hardware

2HP and 4HP Eurorack modules based on Raspberry Pi RP2350 Pico 2

December 2025 - added Version 1.0 2HPico KiCad design files, BOM, Gerbers for main board and panel board and 3D printable panel.

Jan 28/2025 - added Version 1.0 2HPico DSP PCB design files and FR4 front panel design files and gerbers.

Feb 16/2026 - JLCPCB assembly files are now verifed. Minor BOM changes to 2HPico DSP as a result of further testing.

April 13/2026 - added 4HPico DSP PCB files. PCB fabbed, tested and working with 1 jumper.

May 6/2026 - updated 4HPico DSP PCB to V1.1 which corrects missing GND plane connection from middle to bottom of PCB. I have no plans to order these because V 1.0 is fine for me. Changes are minimal so not much risk in ordering V1.1. Added .stl file for 3D printed panel. No plans to do a PCB panel at this point - I'm happy with the 3D printed panel.

July 2/2026 - added 4HPico PCB files

2HPico, 2HPico DSP, 4HPico and 4HPico DSP are complimentary designs intended for different uses:

The 2HPico has 1 or 2 CV inputs and 1 or 2 CV outputs depending on how its jumpered - see notes below. Its dual DAC CV output(s) can also be used for audio generated by the RP2350 processor. 2HPico can be used to process triggers, gates and CV inputs and can generate CV or audio out - its well suited for sequencers, LFOs, oscillators etc.

2HPico DSP has an audio ADC and DAC to enable signal processing for audio effects like delays, reverbs, chorus etc.

2HPico and 2HPico DSP use the same front panel and control panel PCBs.

4HPico is the 2HPico with 2 dedicated CVin, 2 dedicated CVout and two jumperable CV in/outs. Encoder with a 64x32 OLED display instead of pots for setting parameters. This is a single PCB design which requires a 3D printed panel or PCB panel.

4HPico DSP is basically the 2HPico DSP with stereo audio in and out and two dedicated CV inputs. Encoder with a 64x32 OLED display instead of pots for setting parameters. This is a single PCB design which requires a 3D printed panel or PCB panel.

See the repository https://github.com/rheslip/2HPico-Sketches for Pico Arduino sketches to run on the 2HPico.

See the repository https://github.com/rheslip/2HPico-DSP-Sketches for Pico Arduino sketches to run on the 2HPico DSP.

See the repository https://github.com/rheslip/4HPico-DSP-Sketches for Pico Arduino sketches to run on the 4HPico DSP.

See the repository https://github.com/rheslip/4HPico-Sketches for Pico Arduino sketches to run on the 4HPico.

General notes on the designs

Waveshare (and others) make small form factor RP2040 and RP2350 boards which make stuffing one into 2HP possible. The RP2350 has much better performance but for simple things like sequencers, ADSR, LFO etc the RP2040 should work OK. Core 0 runs the main processing loop for the UI and control, core 1 runs the DSP and sends samples to the I2S driver. The code has an option for monitoring the performance of core 1 with a scope. If enabled you will see a pulse on GPIO 8 that indicates how much time core 1 is spending processing samples. If its high more than 100% of the time you will get audio dropouts - time to overclock or optimize your code some more!

The PT8211 16 bit stereo R2R DAC used on the 2HPico and 4HPico is very inexpensive and has proven so far to be quite accurate and consistent from one chip to another (provided they aren't defective - see caveats below). It has no internal antialiasing filters but it works down to DC so can be used as a CV out as well. U6 is a DC coupled antialiasing filter and it also amplifies the DAC output to +-5V eurorack levels.

The 2HPico DSP uses a PCM1808 24 bit stereo audio ADC and a PCM5102A 24 bit stereo audio DAC. The top panel jack is connected to both channels of the PCM1808 and one of the RP2350 ADCs. There is a "DC Input" jumper on the back of the board which shorts the input blocking cap so the top jack can be used for CV input. It adds an approximately 1.6V offset to the input signal so could cause high level audio inputs to clip. Its is recommended to leave the blocking cap in the circuit for audio processing applications. As with the 2HPico, if the "DAC" solder jumper is shorted audio is sent to both of the lower front panel jacks. Both the PCM1808 and PCM5102A have internal antialiasing filters. Note that the 2HPico DSP can not generate CV outputs because the PCM5102A DAC must be AC coupled.

2HPico DSP build is pretty much the same as the 2HPico but you will be populating a couple of different parts - see the BOM.

Panel PCB Build notes

Solder the .1u cap and the RGB LED. Note pin 1 location is NOT the lead with the 45 cut on it - check the picture in the BOM. Hopefully you bought the right pinout! Note these are 5V parts but I haven't had any issues running them at 3.3v - and they are still way too bright!

Solder the jacks - note that the two bottom ones have the same GND via to save real estate

Solder the button. Glue the button cap on with a dab of superglue.

Solder the pots. You can clip the brackets near the bend to make soldering a bit easier but its not required. Make sure they are lined up vertically and horizontally before you solder the brackets to the pads. A Panavise is handy for this step.

Main PCB Build Notes

Solder all the 0603 Rs and Cs first

Solder diodes, R1, U3 regulator, U4 voltage reference and power connector J4. Hook it up to power and check that the 5V, -12V, +12V and -10v reference voltages are OK

Solder in all the chips, the larger caps and the trimpot RV1 (2HPico only).

The Waveshare RP2350 board cannot solder directly to the main PCB because it has components on the bottom side and must stand off a bit. You can solder .1" headers to it and solder the headers to the main PCB or solder .1" header pins in the corners and make the rest of the connections with short wires.

Power up the PCB again and check that the 5V and 3.3V rails are OK.

Solder right angle connectors J1, J2 and J3. The shorter pins solder to the main PCB as shown.

Plug the long end of the right angle connectors into the panel PCB and solder.

Clip the pins on the bottom side of the main PCB so they don't interfere with adjacent modules - a 2HP module is supposed to be only 10.16mm wide.

Solder one of the jumper pads on the bottom to select jack 2 on the panel as either DAC right channel out or a second CV/Gate input. This depends on what the module is supposed to do.

The 2HPico DSP board has a "DC Input" solder jumper that should be shorted if you want to use the top jack as a CV input.

It should be ready to go. You can load up the HWtest sketch and run it to check the pots, button, inputs and DAC functions.

2HPico only - Trim the DAC output

Load up the ADSR app or mod the HWtest sketch so the I2S code is sending the value 0 to the DACs. Measure the level at the output jacks or at U6 pins 1 and 14 and trim RV1 to get as close to 0V as possible. There will probably still be a few mV difference between the channels. Its set up for +-5V output corresponding to -32767 and 32767 DAC values respectively (output amp inverts the DAC signals). If you want higher output levels you can mod the output stage gain but keep in mind the offset and the lowpass filters also have to be recalculated.

Notes on the PT8211 DAC chips for the 2HPico

I bought 10 on Aliexpress and I got a couple of defective ones. Symptom was no output from either left or right DAC, just a low amplitude glitch at the opamp outputs U6 pins 1 and 14. I also got some that were not linear enough for accurate pitch CVout. I suggest you buy from a couple of different vendors and cross your fingers. Alternatively Sparkfun and PJRC sell PT8211 kits for a few dollars that include a PT8211 presumably from a reputable source.

Notes on the PCM1808 and PCM5012A chips for the 2HPico DSP

The PCM1808 ADC is 24 bit only wheras the PCM5102A works with either 16 bit or 24 bit I2S audio. Since they are on the same I2S interface they must both run the same format. I was not able to get 24 bit I2S working with Arduino Pico but it does work with 32 bit I2S. The additional overhead is minimal since the processor and DMA are 32 bits.

Notes on the Panels

STL file is included for a 3D printable panel which includes a collimator that sits over the RGB LED. I glued a short piece of transparent filament inside the collimator as a light pipe - for some reason commercial acrylic light pipes are stupidly expensive. The RGB LED is very bright even on 3.3v so I cut the level back in the code. I will probably design a silkscreened FR4 panel for it at some point.

FR4 front panel gerbers are also included. You will have to make a collimator from a small piece of plastic tubing to direct the RGB LED light to the hole in the panel.

Parts

73
QtyValueFootprintReferences
9.1uCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC4, C9, C10, C12, C13, C14, C15, C16, C19
6PJ3001FBenjmodular:AudioJack_3.5mmJ1, J2, J3, J4, J5, J6
4100kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR6, R8, R16, R21
410kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR23, R24, R26, R28
4180kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR7, R9, R18, R20
41kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR12, R19, R31, R32
4220pCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC5, C6, C17, C18
424kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR11, R15, R29, R30
43.3kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR10, R17, R25, R27
447kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR4, R5, R13, R14
310uCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C2, C8
2100RResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R22
21N5819WSDiode_SMD:D_SOD-123D1, D2
25K Zero TrimPotentiometer_SMD:Potentiometer_Bourns_TC33X_VerticalRV1, RV2
2J2 SELSolderjumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mmJP1, JP2
2MCP6022Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU7, U9
2TL072Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU5, U6
2~Package_SO:SO-8_3.9x4.9mm_P1.27mmU1, U2
12.2kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR2
122uCapacitor_SMD:CP_Elec_5x5.9C3
133uHInductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolderL2
1AMS1117-5.0Package_TO_SOT_SMD:SOT-223-3_TabPin2U3
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ8
1Conn_02x05_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_VerticalJ7
1LM4040DBZ-10Package_TO_SOT_SMD:SOT-23U4
1RP2350-WaveShareMyLibrary:RP2350-WaveshareRZ1
1RotaryEncoder_SwitchMyLibrary:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm_topsolderSW1

More from rheslip/2HPico-Eurorack-Module-Hardware

4
  • 2 layers20.3 × 110 mm4HPicoDSP, the printed circuit board in 3D

    4HPicoDSP

    rheslip/2HPico-Eurorack-Module-Hardware

    2HP Eurorack module based on Raspberry Pi Pico 2

    71 parts84
  • 2 layers70 × 30.3 mmPico 2HP Audio, the printed circuit board in 3D

    Pico 2HP Audio

    rheslip/2HPico-Eurorack-Module-Hardware

    2HP Eurorack module based on Raspberry Pi Pico 2

    58 parts84
  • 2 layers70 × 30.3 mmPico 2HP, the printed circuit board in 3D

    Pico 2HP

    rheslip/2HPico-Eurorack-Module-Hardware

    2HP Eurorack module based on Raspberry Pi Pico 2

    53 parts84
  • 2 layers10 × 110.5 mmPico 2HP Controls, the printed circuit board in 3D

    Pico 2HP Controls

    rheslip/2HPico-Eurorack-Module-Hardware

    2HP Eurorack module based on Raspberry Pi Pico 2

    13 parts84

Similar boards

  • 4 layers40 × 110 mmMMM main, the printed circuit board in 3D

    MMM main

    niektb/sluisbrinkie-eurorack-published

    Published Modules of the Sluisbrinkie project

    145 parts34
  • 2 layers42 × 35 mmLuminosite, the printed circuit board in 3D

    Luminosite

    johan-954/Projet_1DA

    Projet d'électronique de 1ere année

    36 parts
  • 2 layers84.3 × 74 mmOpamps, the printed circuit board in 3D

    Opamps

    bread-modular/bread-modular

    Modular Synths for Everyone

    48 parts67MIT
  • 2 layers30 × 110.5 mmKicad main, the printed circuit board in 3D

    Kicad main

    johannesstrueber/dots

    DOTS eurorack module pcb schematics and code ATMega328 based

    72 parts28
  • 4 layers69.5 × 62.6 mmSensors Module, the printed circuit board in 3D

    Sensors Module

    Queens-Rocket-Engineering-Team/Avionics-23-26

    QRET Avionics hardware, firmware, and documentation for 2023 to 2025.

    197 parts4
  • 2 layers96.6 × 100 mmQuadRaptor, the printed circuit board in 3D

    QuadRaptor

    abdosalem490/QuadRaptor

    148 parts2MIT
  • 2 layers87.5 × 53 mmInterfejs digi, the printed circuit board in 3D

    Interfejs digi

    canislupus11/Digi_interface

    Universal ham radio digi interface.

    104 parts1
  • 2 layers106.5 × 125.4 mmRP2040 KBD, the printed circuit board in 3D

    RP2040 KBD

    jay94ks/simple-np

    Simple Number Pad based on RP2040

    120 parts1MIT

Questions

How big is the 4HPico PCB?

It measures 20.3 × 110 mm and has 2 copper layers, 1.6 mm thick.

What parts does the 4HPico use?

73 parts, built around the MCP6022-I/P, TL072, AMS1117-5.0 and 1N5819WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 4HPico KiCad files?

From the rheslip/2HPico-Eurorack-Module-Hardware repository on GitHub, at the commit this page was made from: the board is 4HPico KiCad design files/4HPico.kicad_pcb and its schematic 2HPico DSP KiCad Design Files/Pico 2HP_Audio/Pico 2HP_Audio.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the 4HPico design in my own project?

Its repository states no licence, so its author keeps all rights: ask rheslip before reusing the design.