

QuadRaptor
- Size
- 96.6 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 148
- Nets
- 139
- Pads
- 549
- Tracks, vias
- 2,623, 339
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 11 Jan 2024
- Updated
- 20 Jul 2024
Overview
QuadRaptor is an open-source printed circuit board by abdosalem490, from the abdosalem490/QuadRaptor repository on GitHub, published under the MIT licence. It is a 2-layer board of 96.6 × 100 mm with 148 parts on 139 nets, routed with 2,623 tracks and 339 vias.
It is built around the CH32V203C8T6, BMP280 and PAM8403DR, with the AMS1117-3.3, AMS1117-5.0 and ADXL345BCCZ among its other parts. Its parts include 42 capacitors, 25 connectors, 19 resistors, 12 ICs and 6 diodes. It belongs with the RISC-V boards of this library.
Main components
11CH32V203C8T6
LQFP-48(7x7)144MHz 64KB FLASH Others LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSWCH (Nanjing Qinheng Microelectronics)Microcontrollers (MCU/MPU/SOC)BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsPAM8403DR
SOIC-16-40℃~+85℃ -59dB 0.15% 2 Single-Ended Inputs 2-Channel 2.8V~5.5V 3Wx2@4Ω 80dB 87% 8mA Class D Filterless architecture SOIC-16 Audio Amplifiers ROHSDiodes IncorporatedAudio AmplifiersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsADXL345BCCZ
LGA-14(3x5)-40℃~+85℃ 100nA 16bit 2V~3.6V Accelerometer SPI、I2C X,Y,Z ±16g 运动事件检测 LGA-14(3x5) Accelerometers ROHSAnalog DevicesAccelerometersHMC5883L
LGA-16_L3.0-W3.0-P0.50LPCC-16(3x3) New Arrivals ROHSHoneywellUncategorisedMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesTIP121
TO-220-31000 2.5V 200uA 2W 4V 5A 5V 80V NPN TO-220-3 Darlington Transistors ROHSSTMicroelectronicsDarlington TransistorsTYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB Connectors
README
README.mdQuadRaptor
Parts
148| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | TestPoint | TestPoint:TestPoint_Bridge_Pitch2.54mm_Drill1.0mm | TP1, TP2, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP19, TP21, TP23, TP24, TP25, TP27 +8 |
| 13 | 0.1 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6, C7, C8, C10, C11, C15, C24, C38, C43, C44, C45, C46, C47 |
| 9 | 10 uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9, C13, C29, C30, C31, C32, C33, C41, C42 |
| 8 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4, H5, H6, H7, H8 |
| 6 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4, C21, C22, C23, C25 |
| 6 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2, J14, J15, J16, J17, J18 |
| 5 | Conn_01x04 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J10, J19, J20, J21, J22 |
| 4 | 1 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12, C34, C36, C37 |
| 4 | 10 Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R10, R15, R19 |
| 4 | 20pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C5, C27, C28 |
| 4 | 330 ohm | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R8, R16, R17 |
| 4 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6, J7, J8, J9 |
| 4 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2, D3, D4 |
| 3 | 4.7 Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R4 |
| 2 | 0.47 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C39, C40 |
| 2 | 10Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14, R18 |
| 2 | 1N5819WS | Diode_SMD:D_SMA | D5, D6 |
| 2 | 20 Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12 |
| 2 | 5.1 Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7 |
| 2 | 8 MHZ | Crystal:Crystal_HC18-U_Vertical | Y1, Y2 |
| 2 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U7, U12 |
| 2 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U9, U11 |
| 2 | CH32V203C8T6 | CH32V203:CH32V203C8T6_LQFP-48_7x7mm_P0.5mm | U1, U2 |
| 2 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1, J13 |
| 2 | Conn_01x06 | Connector_JST:JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J5, J23 |
| 2 | LOGO | dummy:logo2 | G***, G*** |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW1, SW2 |
| 2 | Speaker (3W 4ohm) | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | LS1, LS2 |
| 1 | 0.22 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14 |
| 1 | 1 Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13 |
| 1 | 15 Kohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 220 pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 4.7 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16 |
| 1 | 470 uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C35 |
| 1 | ADXL345BCCZ | digikey-footprints:LGA-14_3x5mm_RevA | U3 |
| 1 | BMP280 | digikey-footprints:LGA-8_2x2.5mm_BMP280 | U4 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J25 |
| 1 | Conn_01x04 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J24 |
| 1 | Conn_02x04 | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J12 |
| 1 | Conn_02x09_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x09_P2.54mm_Vertical | J11 |
| 1 | HMC5883L | _sensors:_HMC5883L | U6 |
| 1 | MCP4921-EMC | Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.68x1.88mm | U14 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U10 |
| 1 | Micro_SD_Card | footprints:J_SD_Card-micro_socket_A | J4 |
| 1 | PAM8403D | Package_SO:SOP-16_3.9x9.9mm_P1.27mm | U8 |
| 1 | SW_DIP_x01 | EG1218:SW_EG1218 | SW3 |
| 1 | SW_SPDT | EG1218:SW_EG1218 | SW4 |
| 1 | TIP121 | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | TYPE-C-31-M-12 | TYPE-C-31-M-12:HRO_TYPE-C-31-M-12 | J26 |
Similar boards
- 4 layers45 × 89 mm

- 4 layers26.5 × 57.4 mm

MotorDriver
Kmshanley/MiniRobots
Firmware and PCB desgin for mini robots with UWB localization and lidar mapping
50 parts1 - 2 layers40 × 40 mm

SkyIMU
rmingon/SkyIMU
Compact 3.3 V sensor board that combines an InvenSense MPU-6050 6-axis IMU, a Honeywell HMC5883L 3-axis magnetometer, and a Bosch BMP280 barometric pressure and temperature sensor.
20 parts - 2 layers191.3 × 164 mm

XYmatics E64
XyrusB2010/XYmatics-E64
A 5-axis Klipper mainboard, powered by a Raspberry Pi Compute Module and STM32F407
282 parts - 4 layers82 × 100 mm

Falcon Edge
rmingon/Falcon-Edge
A 3D-printable flying-wing airframe with a custom ESP32 flight computer—open hardware you can solder, screw together, and fly.
48 parts11 - 2 layers95.9 × 112.6 mm

- 2 layers75 × 50 mm

Aire apollo
makespacemadrid/ApolloVentilator
Nos gustaría ser el Marlin de los ventiladores :)
37 parts6GPL-3.0 - 2 layers81.2 × 82.6 mm

Questions
How big is the QuadRaptor PCB?
It measures 96.6 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the QuadRaptor use?
148 parts, built around the CH32V203C8T6, BMP280, PAM8403DR and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the QuadRaptor KiCad files?
From the abdosalem490/QuadRaptor repository on GitHub, at the commit this page was made from: the board is hardware/pcb design files/quadraptor/quadraptor.kicad_pcb and its schematic hardware/pcb design files/quadraptor/quadraptor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the QuadRaptor design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).