Skip to the content
2 layers135.1 × 85.8 mmWinchester, the printed circuit board in 3D

Open source JAMMA supergun project. KiCAD PCB design files

Size
135.1 × 85.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
89
Nets
117
Pads
475
Tracks, vias
996, 248
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
4 May 2021
Updated
11 May 2021

Overview

Winchester is an open-source printed circuit board by yoonjustin, from the yoonjustin/WinchesterPCB repository on GitHub, published under the MIT licence. It is a 2-layer board of 135.1 × 85.8 mm with 89 parts on 117 nets, routed with 996 tracks and 248 vias.

It is built around the TEENSY 4.1, FE1.1S and LM1881, with the THS7376IPW, BA7230LS and ECS-120-S-4 among its other parts. Its parts include 24 capacitors, 21 resistors, 13 transistors, 3 connectors and 2 ICs. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

7

README

README.md

WinchesterPCB

Open source JAMMA supergun project. KiCAD PCB design files, included are the symbols, footprints and BOM. The board is a two sided pcb with 1oz copper. Roughly 135mm x 86mm

Design Breakdown

Power

Power is supplied using a 20pin atx power connector. That way it can provide +5, -5 and +12v without having to deal with conversion on the pcb itself. In addition, it makes it easy to include a power switch and power led on the pcb. There is also logic in the atx power supply to cut power in the event of a short circuit. Which is a nice safety feature.

The +5v power to the jamma connector needs to be pretty wide and beefy. If we assume 5A through a 1oz copper board thats about 5 inches, a 20 degree raise in temp puts us around 2.59mm trace width. I feel ok with the 2.5mm trace width on the board. Both the +5v and +12v are passing through an INA260 power monitoring IC. The INA260 can handle up to 36v and 15A, so its well within the use of this project.

The teensy 4.1 uses 100mA, the oled screen 20mA, THS7376 30mA, FE1.1s 142mA, BA7230LS 50mA, and the MIC2026 is less than 1mA. So the total power consumption of the +5v coponents on the board is about 350mA. Using the .6mm trace with feels about right.

I also made sure not to connect the +5v directly to the pins on the usb ports. The MIC2026-2YM will provide the usb ports with power according to the usb specifications. If anything goes out of spec, the MIC2026 will tell the FE1.1s usb hub to turn off the ports. This should help protect the board and the connected device, incase something goes wrong.

Component Video

Jamma arcade games were designed with outputting the video signal to an RGBS compatible display. And when it comes to home compatible tvs, component video is the closest to that signal. Composite video is a more common analog video input, but arcade games wont benefit from any kind of dithering effects.

The RGB signals are passed through individual potentimeters and sent to the BA7230LS to be converted to component signals. Those are then sent to a THS7376 video amplifier and connected to the sync signal which is cleaned up with an LM1881.

The THS7376 video amplifier is a drop in replacement for the THS7374. Either chip is supported in this design. Its worth noting that the 7374 uses much less power than the 7376, but Im not sure how the video quality is between the two. Im not sure if its my crt tv or my eyes, but I dont seem much different enabling and disabling the lowpass filter on the 7376.

Teensy 4.1

The teensy 3.6 should also work for this design, but considering the 4.1 model is cheaper and faster, I dont see the point in using 3.6 unless you have one on hand. Due to the fact that the teensy 4.1 is not 5v tolerant, I have the pins connected to biased BJT transistors to connect the jamma pins to ground to signal a button press. The transistors have 1k resistors built in connecting the teensy io pin to the base and between the base and the emitter. One small design flaw is that the Player 1 Up signal is using pin 13 on the teensy, which is connected to an led. So every time player presses the up button the led lights up. I was hoping there would be a way to disable the led, but it is hard wired to the pin.

Be careful not to have the atx power and have the teensy plugged in with the onboard micro usb port at the same time. If you do want to have both plugged in and powered at the same time use this guide to do it safely https://www.pjrc.com/teensy/external_power.html.

PCB

There are in pad vias in this design. If assembling by hand its not a problem, but some machines do have problems with placing the correct amount of solder the pads with vias.

Both the front and back planes of the pcb are filled with ground. I also added vias along the outside for ground stitching. I dont think its that applicable for this project, but it doesnt hurt anything either.

All of the connectors, power switch, power led, oled display and potentiometers are using through hole designs incase someone wants to put the board inside of a case. Wires could be ran to connectors on the side of a case.

The expansion pins are using a footprint of a flat flex connector(SLW8R-5C7LF). A pcb could be mounted on top of the right side, there is another mounting hole near the LM1881 IC.

Future Design Considerations

The BA7230LS and FE1.1s are easy to use but not so easy to order and aquire. I have actually gotten some bad BA7230LS's from ebay and it would be nice to use a usb hub with better documentation for robust designs. I wish it had separate OVJ and enable lines for each port. This design from GGLABs converts rgb signals using OPAMPs and it might replace using the BA7230LS https://gglabs.us/sites/gglabs.us/files/a520hd_sch-A00.pdf. As for the usb hub, TI makes a wide variety of hubs but none are using the nice SSOP package.

There is an issue with PS3 controllers locking up the usbhub when connecting, that happens intermittantly. Its puzzling since ps4 and xbox one controllers do not exhibit this behavior. Retrocution sells a usb hub that also uses the FE1.1s and warns not to use pinheaders when connecting usb ports. I wonder if its a connection issue somehow. I also have an issue with using a Hori RAP N model fight stick. It connects for about a second and then disconnects. Either way, using a more modern usb hub from TI would be on the table for a board redesign.

Disclaimer

I did include the MIT license to this project, but to I would like to also state:

  • I offer NO WARRANTY of any kind and assume NO RESPONSIBILITY for any potential damage caused by this device.
  • You are free to build, use, sell, distribute as you like. Please credit and link this project if you are promoting this design

Parts

89
QtyValueFootprintReferences
13MUN5230DW1T1GTO_SOT_Packages_SMD:SOT-363_SC-70-6_HandsolderingQ1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12, Q13
90.1uFWinchester:C_1206_HandSolderingC1, C6, C7, C21, C22, C26, C27, C28, C29
6MountingHoleWinchester:MountingHole_3.2mm_M3H1, H2, H3, H4, H5, H6
510kWinchester:R_1206_HandSolderingR1, R11, R12, R15, R16
4390ohmWinchester:R_1206_HandSolderingR3, R6, R7, R8
310uFWinchester:C_1206_HandSolderingC2, C4, C5
31uFsamacsys:EEE1HA010SRC19, C20, C23
3220uFWinchester:CP_Tantalum_Case-D_EIA-7343-31_HandC30, C31, C32
33.6MohmWinchester:R_1206_HandSolderingR23, R24, R25
3R_POT_TRIMsamacsys:3362P_1B_POT1, G_POT1, R_POT1
21uFWinchester:C_1206_HandSolderingC11, C14
2220uFsamacsys:EEE-1CA221XPC3, C8
2INA260samacsys:INA260INA260-1, INA260-2
2USB_Asamacsys:875201010BLFUSB1, USB2
10.047uFWinchester:C_1206_HandSolderingC25
110uFsamacsys:EEE-1EA100SRC24
11KohmWinchester:R_1206_HandSolderingR4
12.7kWinchester:R_1206_HandSolderingR5
1200ohmWinchester:R_1206_HandSolderingR26
1330Winchester:R_1206_HandSolderingR17
156ohmWinchester:R_1206_HandSolderingR20
1680kWinchester:R_1206_HandSolderingR18
175ohmWinchester:R_1206_HandSolderingR22
182ohmWinchester:R_1206_HandSolderingR19
191ohmWinchester:R_1206_HandSolderingR21
1ATX20Winchester:Molex_MiniFit-JR-5556-20A_2x10x4.20mm_StraightATX1
1BA7230LSWinchester:szip24BA7230LS1
1Conn_01x03_FemalePin_Headers:Pin_Header_Straight_1x03_Pitch2.54mmJ1
1ECS120samacsys:ECS120184XCKMY1
1FE1.1sHousings_SSOP:SSOP-28_3.9x9.9mm_Pitch0.635mmFE1.1s1
1JST-XHConnectors_JST:JST_XH_S06B-XH-A_06x2.50mm_AngledKICK1
1JammaWinchester:JAMMA56HALFU1
1LEDWinchester:LED_D3.0mmD1
1LM1881samacsys:LM1881LM1881
1LogoWinchester:v1L1
1Logo_Open_Hardware_SmallSymbols:OSHW-Logo2_7.3x6mm_SilkScreenLOGO1
1MIC2026-2YMsamacsys:SOIC127P599X173-8NMIC2026
1PJRANWinchester:PJRANCOMPONENT1
1SLW8R-5C7LFsamacsys:SLW8R5C7LFJ2
1SSD1306 OLEDadafruitoled:Adafruit_SSD1306J3
1SW_DPDT_x2Winchester:POWER_SWPOWER1
1THS7376Winchester:TSSOP-14_4.4x5mm_Pitch0.65mmTHS7376
1Teensy4.1teensy:Teensy41U7

Similar boards

  • 2 layers43.1 × 48.9 mmConverter, the printed circuit board in 3D

    Converter

    NEO-JAMMA/Neo-Geo_MVS_Projects

    Neo-Geo MVS Projects

    36 parts30GPL-3.0
  • 2 layers42.4 × 18.4 mmSNEdge, the printed circuit board in 3D

    SNEdge

    ThunderTechnologies/SNEdge

    An open source edge sharpener for the SNES

    37 parts77CERN-OHL-W-2.0
  • 2 layers55.9 × 37.2 mmHKTV13RGB, the printed circuit board in 3D

    HKTV13RGB

    RetroLoom/HKTV13RGB

    Open-hardware RGB mod for the Emerson HKTV13 "Hello Kitty" CRT TV — an interposer board that injects switchable external RGB while preserving the original OSD.

    35 partsCERN-OHL-S-2.0
  • 2 layers100 × 100 mmSync ope, the printed circuit board in 3D

    Sync ope

    cyberboy666/sync_ope

    effect send + sync restoring circuit - adapted from a gael jaton design

    78 parts52
  • 2 layers48.7 × 63.5 mmSCART to VGA, the printed circuit board in 3D

    SCART to VGA

    arithmaldor/SCART-to-VGA

    SCART to VGA adapter with optional sync stripper.

    15 parts46
  • 2 layers99 × 90 mmExtron input, the printed circuit board in 3D

    Extron input

    rattboi/extron-scart-adapter

    Cheap adapter for (some) extron matrix switchers to allow SCART input with no cables

    22 parts37
  • 2 layers50 × 70 mmRgbntsc, the printed circuit board in 3D

    Rgbntsc

    jamvanderloeff/RGB-to-NTSC

    Converts RGB 15kHz video in the form of VGA or SCART into NTSC and/or PAL composite and s-video using

    55 parts17MIT
  • 2 layers50 × 70 mmRGB to component, the printed circuit board in 3D

    RGB to component

    jamvanderloeff/RGB-to-component

    58 parts13MIT

Questions

How big is the Winchester PCB?

It measures 135.1 × 85.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Winchester use?

89 parts, built around the TEENSY 4.1, FE1.1S, LM1881 and THS7376IPW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Winchester KiCad files?

From the yoonjustin/WinchesterPCB repository on GitHub, at the commit this page was made from: the board is Winchester.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Winchester design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).