
Sync ope
cyberboy666/sync_ope
effect send + sync restoring circuit - adapted from a gael jaton design

SCART to VGA adapter with optional sync stripper.
SCART to VGA is an open-source printed circuit board by arithmaldor, from the arithmaldor/SCART-to-VGA repository on GitHub. It is a 2-layer board of 48.7 × 63.5 mm with 15 parts on 31 nets, routed with 100 tracks and 9 vias.
It is built around the LM1881. Its parts include 5 capacitors, 4 connectors, 1 resistor, 1 IC and 1 switch.
Adapt SCART to VGA (RGBS) with optional sync stripper. You can either include all the parts and select on and off with the switch, or leave the sync stripper circuit off entirely and just connect the center leg of the switch with the leg nearest the "Bypass" text.
Licensed under CERN OHL 1.2.
Thanks to Beyond Pixels (@ChristianBruyer) for the request/suggestion.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2, C4 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5 |
| 1 | 10uF | Capacitor_SMD:CP_Elec_5x5.3 | C3 |
| 1 | 220OHM | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB1 |
| 1 | 680K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1 |
| 1 | AudioJack3 | digikey-footprints:Headphone_Jack_3.5mm_SJ1-3523N | J5 |
| 1 | Conn_01x03_Male | Tinkerplunk:DPDT | SW1 |
| 1 | DB15_Female_HighDensity | Tinkerplunk:VGA | J4 |
| 1 | LM1881 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | SCART-F | SCART to DVI-A Compact:SCART-F | J1 |
| 1 | SolderJumper_3_Bridged12 | Tinkerplunk:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | +5V Source |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J3 |
The 14 most common of 15 parts.

cyberboy666/sync_ope
effect send + sync restoring circuit - adapted from a gael jaton design

rattboi/extron-scart-adapter
Cheap adapter for (some) extron matrix switchers to allow SCART input with no cables

jamvanderloeff/RGB-to-NTSC
Converts RGB 15kHz video in the form of VGA or SCART into NTSC and/or PAL composite and s-video using




yoonjustin/WinchesterPCB
Open source JAMMA supergun project. KiCAD PCB design files

bigbass1997/PICTAS
Low-cost replay device for playing back Tool Assisted Speedruns on real hardware
It measures 48.7 × 63.5 mm and has 2 copper layers, 1.6 mm thick.
15 parts, built around the LM1881. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the arithmaldor/SCART-to-VGA repository on GitHub, at the commit this page was made from: the board is SCART to VGA.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask arithmaldor before reusing the design.