6 layers76.5 × 69 mm
Fmc usb gpio spi jtag
chipsalliance/rocket-pcb
PCB libraries and templates for rocket-chip based FPGA/ASIC designs
146 parts21Apache-2.0
6 layers76.5 × 69 mm
Fmc usb gpio spi jtag
vowstar/rocket-pcb-orig2FMC template board
- Size
- 76.5 × 69 mm
- Copper layers
- 6
- Thickness
- 1.62 mm
- Parts
- 146
- Nets
- 282
- Pads
- 892
- Tracks, vias
- 2,564, 728
- Pours
- 6,288
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 31 Jan 2023
- Updated
- 17 May 2023
Overview
Fmc usb gpio spi jtag is an open-source printed circuit board by vowstar, from the vowstar/rocket-pcb-orig repository on GitHub, published under the Apache-2.0 licence. It is a 6-layer board of 76.5 × 69 mm with 146 parts on 282 nets, routed with 2,564 tracks and 728 vias.
It is built around the STUSB03EQR, TXS02612RTWR and CH9102F, with the MMC5603NJ, MT2492 and TPD4E02B04DQAR among its other parts. Its parts include 54 resistors, 31 capacitors, 19 ICs, 17 diodes and 8 connectors. It belongs with the interfaces and adapters boards of this library.
Main components
12
STUSB03EQR
QFN-16-EP(3x3)-40℃~+85℃ 12Mbps 4V~5.5V 5.5mA 5uA Transceiver USB 2.0 QFN-16-EP(3x3) USB Converters ROHSSTMicroelectronicsUSB Converters
TXS02612RTWR
WQFN-24-EP(4x4)-40℃~+85℃ 1.1V~3.6V 120Mbps 12uA、24uA WQFN-24-EP(4x4) Interface - Specialized ROHSTexas InstrumentsInterface - Specialized
CH9102F
QFN-24-EP(4x4)-40℃~+85℃ 1.8V、2.5V、3.3V、5V 3mA 4Mbps 90uA USB 2.0 USB to UART QFN-24-EP(4x4) USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
MMC5603NJ
WLP-4(0.8x0.8)-40℃~+85℃ 1.62V~3.6V 20bit 750uA、1.3mA、2.4mA、3.4mA I2C ±3mT ±3mT WLP-4(0.8x0.8) 3D Magnetic Sensors ROHSMEMSIC3D Magnetic Sensors
MT2492
SOT-23-6-40℃~+85℃@(TA) 1 2A 4.5V~16V 600kHz Adjustable Buck Buck Built-in Yes SOT-23-6 DC-DC Converters ROHS西安航天民芯DC-DC Converters
TPD4E02B04DQAR
USON-10(1x2.5)-40℃~+125℃ 0.33pF 10nA 17W@8/20us 2A@8/20us 3.6V 7.5V 8.8V Bidirectional Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 TVS USON-10(1x2.5) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD And Surge Protection (TVS/ESD)
M24C02-FMN6P
SOIC-8-40℃~+85℃ 1.7V~5.5V 200 Years 2Kbit 4,000,000 Cycles 400kHz 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C SOIC-8 EEPROM ROHSSTMicroelectronicsEEPROM
NCD1206Y1
1206-30℃~+85℃ 1.6V~2.6V 130° 180mcd 25mA 586nm~593nm 595nm 65mW Discrete Diode Yellow 1206 LED Indication - Discrete ROHSFoshan NationStar OptoelectronicsLED Indication - DiscreteNCD1206O1
1206-30℃~+85℃ 1.6V~2.6V 130° 25mA 589nm~610nm 610nm 65mW 80mcd~220mcd Discrete Diode Orange Top-mount 1206 LED Indication - Discrete ROHSFoshan NationStar OptoelectronicsLED Indication - Discrete
TL3342F160QG
SMD-4P,5.2x5.2mm-20℃~+70℃ 1.54mm 1.6N 100,000 cycles 12V 5.2mm 5.2mm 50mA Gull Wing Round Button SPST Surface Mount,Vertical Without Bracket Yellow SMD-4P,5.2x5.2mm Tactile Switches ROHSE-SwitchTactile SwitchesM2.5
-0.45mm 2.5mm 2mm 5mm DIN934 Hex M2.5X0.45 Nickel plated Silver white - Hexagonal nutsShuntianHex NutACA-SPI-004-K02
-- Programmers, Emulators, and Debuggers ROHSLOTESProgrammers, Emulators, And Debuggers
README
fmc_basic_peripheral/README.mdFMC_BASIC_PERI
The basic peripherals of the FPGA mezzanine card, including JTAG, UART, GPIO, USB, I3C, etc., can be used for prototype verification of the basic peripherals of the SoC.
Preparation
Install kicad7, cmake, ninja, frugy.
Precautions
When using it for the first time, it is necessary to program the IPMI FRU data for the EEPROM so that the development board can identify the power supply of the FMC.
Build
cmake -G Ninja -B build
cmake --build buildIf you only need to build the eeprom binary,
cmake --build build --target eepromIf you only need to generate a pdf of the schematic or pcb,
cmake --build build --target pdfIf you need to generate complete production data,
cmake --build build --target productionParts
146| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C22, C23, C25, C26, C27, C28, C29, C30, C31, C32, C37, C38, C39, C40 +5 |
| 20 | 10k | Resistor_SMD:R_0402_1005Metric | R11, R12, R19, R20, R21, R22, R25, R26, R27, R28, R37, R42, R43, R45, R47, R48 +4 |
| 16 | 6.8k | Resistor_SMD:R_0402_1005Metric | R5, R6, R7, R8, R9, R10, R18, R29, R30, R31, R32, R38, R39, R40, R41, R46 |
| 11 | NCD1206Y1 | LED_SMD:LED_1206_3216Metric | D1, D2, D3, D4, D5, D7, D8, D9, D10, D11, D17 |
| 8 | TXS02612RTWR | CHIPSAlliance_Package_DFN_QFN:WQFN-24-1EP_4x4mm_P0.5mm_EP2.45x2.45mm | U4, U11, U14, U15, U16, U17, U26, U27 |
| 7 | 47k | Resistor_SMD:R_0402_1005Metric | R13, R14, R15, R16, R17, R23, R24 |
| 6 | 1mm | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3, FID4, FID5, FID6 |
| 6 | NCD1206O1 | LED_SMD:LED_1206_3216Metric | D6, D12, D13, D14, D15, D16 |
| 5 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R35 |
| 5 | TL3342F160QG | Button_Switch_SMD:SW_SPST_TL3342 | SW2, SW7, SW8, SW9, SW10 |
| 4 | TPD4E02B04DQA | Package_SON:USON-10_2.5x1.0mm_P0.5mm | U12, U18, U19, U20 |
| 3 | 4.7u | Capacitor_SMD:C_0402_1005Metric | C4, C6, C9 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C3, C10 |
| 2 | 20R | Resistor_SMD:R_0402_1005Metric | R44, R53 |
| 2 | AIP74LVC1T45GB236TR | Package_TO_SOT_SMD:SOT-23-6 | U5, U22 |
| 2 | M2.5 | CHIPSAlliance_MountingHole:MountingHole_2.7mm_M2.5_FMC_Pad | H3, H4 |
| 2 | M2.5 | CHIPSAlliance_MountingHole:MountingHole_2.7mm_M2.5_FMC_Pad_Via | H1, H2 |
| 2 | PM2.54-2x6 | Connector_PinSocket_2.54mm:PinSocket_2x06_P2.54mm_Vertical | J6, J8 |
| 2 | USB_C_Receptacle | CHIPSAlliance_Connector:USB_C_Receptacle_Molex_105450-0101 | J3, J4 |
| 1 | 0.1u | Capacitor_SMD:C_0402_1005Metric | C36 |
| 1 | 0R(DNI) | Resistor_SMD:R_0402_1005Metric | R36 |
| 1 | 100k 1% | Resistor_SMD:R_0402_1005Metric | R33 |
| 1 | 15k | Resistor_SMD:R_0402_1005Metric | R54 |
| 1 | 22k 1% | Resistor_SMD:R_0402_1005Metric | R34 |
| 1 | 22n | Capacitor_SMD:C_0402_1005Metric | C33 |
| 1 | 22p | Capacitor_SMD:C_0402_1005Metric | C34 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric | C35 |
| 1 | 22u ±20% 35V | Capacitor_SMD:C_0805_2012Metric | C24 |
| 1 | 4.7uH ±20% 1.6A TFM252012ALMA4R7MTAA | Inductor_SMD:L_Sunlord_SWPA252012S | L1 |
| 1 | ACA-SPI-004-K02 | CHIPSAlliance_Connector:ACA-SPI-004 | J2 |
| 1 | CH9102F | CHIPSAlliance_Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U3 |
| 1 | Conn_JTAG_20 | Connector_IDC:IDC-Header_2x10_P2.54mm_Vertical | J5 |
| 1 | DSHP04TSGET | Button_Switch_SMD:SW_DIP_SPSTx04_Slide_KingTek_DSHP04TS_W7.62mm_P1.27mm | SW1 |
| 1 | M24C02-FMN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | MMC5603NJ | CHIPSAlliance_Sensor:WLP4_N40P2X2_80X80X52N | U25 |
| 1 | MT2492 | Package_TO_SOT_SMD:SOT-23-6 | U13 |
| 1 | Micro_SD_Card_Det2 | CHIPSAlliance_Connector:microSD_HC_Molex_104031-0811 | J7 |
| 1 | SAMTEC_ASP-134604-01 | CHIPSAlliance_Connector:Samtec_FMC_ASP-134604-01_4x40_P1.27mm | J1 |
| 1 | STUSB03EQR | CHIPSAlliance_Interface:QFN_B03EQR_STM | U2 |
Similar boards
- 2 layers75.1 × 100 mm
- 4 layers58 × 66 mm
H616 devboard
Bogdan8266/h616-board
8-layer Allwinner H616/618 SBC with DDR3, USB, Wi-Fi/BT and battery power support, designed for embedded Linux.
165 parts4CERN-OHL-P-2.0 - 4 layers39.5 × 80 mm
- 4 layers75 × 50 mm
- 4 layers118 × 117 mm
Cm4-robot
Twisted-Fields/acorn-robot-electronics
PCB hardware designs in KICAD for Acorn, the precision farming rover from Twisted Fields.
268 parts81 - 4 layers100 × 100 mm
Phmod
gallicchio/AMOD-and-RFMOD
The tutorial's 2x12 adapter (/mudd/133electronics/icepi-zero-dac-adc/adapterboard/) with a 2 x 6 right-angle Pmod socket on a 15 mm extension of its right-hand end, so an Icepi Zero can drive AMOD-A's and RF-MOD's Pmod…
234 parts - 4 layers89.5 × 70 mm
Questions
How big is the Fmc usb gpio spi jtag PCB?
It measures 76.5 × 69 mm and has 6 copper layers, 1.62 mm thick.
What parts does the Fmc usb gpio spi jtag use?
146 parts, built around the STUSB03EQR, TXS02612RTWR, CH9102F and MMC5603NJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Fmc usb gpio spi jtag KiCad files?
From the vowstar/rocket-pcb-orig repository on GitHub, at the commit this page was made from: the board is fmc_basic_peripheral/fmc_usb_gpio_spi_jtag.kicad_pcb and its schematic fmc_basic_peripheral/fmc.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Fmc usb gpio spi jtag design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).