Skip to the content

MMC5603NJ

MEMSICExtended

-40℃~+85℃ 1.62V~3.6V 20bit 750uA、1.3mA、2.4mA、3.4mA I2C ±3mT ±3mT WLP-4(0.8x0.8) 3D Magnetic Sensors ROHS

Part id
memsic/MMC5603NJ
Category
3D Magnetic Sensors
Package
WLP-4(0.8x0.8)
Pins
4
In stock
31,401 at JLCPCB (C404328)
Used on
28 open-source boards

Overview

The MMC5603NJ is a 3D Magnetic Sensor made by MEMSIC in a WLP-4(0.8x0.8) package with 4 pins. -40℃~+85℃ 1.62V~3.6V 20bit 750uA、1.3mA、2.4mA、3.4mA I2C ±3mT ±3mT WLP-4(0.8x0.8) 3D Magnetic Sensors ROHS.

PCBKit's library has its KiCad symbol (MMC5603NJ:MMC5603NJ, from Antmicro) and its footprint (wlp-4-0-82x0-82mm:WLP-4_0.82x0.82mm, from Antmicro), ready for a KiCad board. 31,401 are in stock at JLCPCB (part C404328). 28 open-source boards in 25 repositories on GitHub use it.

Symbol

A1VSAA2SCLB1VDDB2SDA
MMC5603NJ:MMC5603NJFrom Antmicro

Footprint

wlp-4-0-82x0-82mm:WLP-4_0.82x0.82mmFrom Antmicro

From the datasheet

10
Supply, least
1.62 V · VDD, recommended operating min · p. 2
Supply, most
3.6 V · VDD, recommended operating max · p. 2
Supply, least
1.2 V · VIO, recommended operating min · p. 2
Supply, absolute maximum
5 V · VDD, absolute maximum · p. 4
Works from
-40 °C · Operating temperature min · p. 2
Works up to
85 °C · Operating temperature max · p. 2
Takes working
1.3 mA · VDD, typical at 100 measurements/second, BW=10, 1.8 V · p. 2
Takes at most
4 mA · VDD, max at 100 measurements/second, BW=00, 1.8 V · p. 2
Takes asleep
1 µA · VDD, typical power down current · p. 2
Data rate, most
400 kbit/s · I2C FAST mode max · p. 1

What it is and has

10
Magnetic field range
±30 G FSR · p. 1
Resolution
20 bits · p. 1
Magnetic resolution
0.0625mG per LSB · p. 1
Noise
2 mG total RMS · p. 1
Heading accuracy
±1º · p. 1
Frequency response
Up to 1KHz · p. 1
I2C
Slave, FAST mode up to 400 KHz · p. 1
I3C
Available · p. 1
Logic IO
1.2V · p. 1
Compliance
RoHS · p. 1

Around it

3
cap 2.2 µF
between VDD and VSA; Minimum bypass capacitance; place close to VDD. · p. 5
res 2.7Kohm
between SDA and pull-up supply; I2C pull-up for a short bus, less than 10 cm. · p. 5
res 10Kohm
between SDA and pull-up supply; I2C pull-up for a bus less than 5 cm. · p. 5

Specifications

43
ParameterConditionsAs printedPage
Field Range (Each Axis)1Total applied field; each axis; ± rangetyp 30 G2
Supply Voltage VDDmin 1.62 · typ 1.8 · max 3.6 V2
VIO VIOMaximum is VDDmin 1.2 · typ 1.8 V2
Supply Voltage rise timemax 10 ms2
Supply Current2,3100 measurements/second; BW=00; VDD=1.8 V; Auto_SR_en=1; 25 °Ctyp 3.4 · max 4 mA2
Supply Current2,3100 measurements/second; BW=01; VDD=1.8 V; Auto_SR_en=1; 25 °Ctyp 2.4 · max 3 mA2
Supply Current2,3100 measurements/second; BW=10; VDD=1.8 V; Auto_SR_en=1; 25 °Ctyp 1.3 · max 1.6 mA2
Supply Current2,3100 measurements/second; BW=11; VDD=1.8 V; Auto_SR_en=1; 25 °Ctyp 0.75 · max 1 mA2
Power Down Current3VDD=1.8 V; Auto_SR_en=1; 25 °Ctyp 1 · max 1.2 uA2
Operating Temperaturemin -40 · max 85 C2
Storage Temperaturemin -55 · max 125 C2
Linearity Error3 (Best fit straight line)FS=±30 G; Happlied=±15 Gtyp 0.5 · max 0.75 %FS2
Hysteresis33 sweeps across ±30 Gtyp 0.02 · max 0.1 %FS2
Repeatability Error33 sweeps across ±30 Gtyp 0.02 · max 0.1 %FS2
Alignment ErrorTypical and maximum are stated as ± valuestyp 1 · max 3 Degrees2
Transverse SensitivityTypical and maximum are stated as ± valuestyp 2 · max 5 %2
Total RMS Noise3BW=00typ 1.5 · max 2.5 mG2
Total RMS Noise3BW=01typ 2 · max 4 mG2
Total RMS Noise3BW=10typ 3 · max 5 mG2
Total RMS Noise3BW=11typ 4 · max 7 mG2
Output resolutiontyp 20 Bits2
Max Output data rate4BW=00min 75 Hz2
Max Output data rate4BW=01min 150 Hz2
Max Output data rate4BW=10min 255 Hz2
Max Output data rate4BW=11; 1000 Hz requires Register ODR=255 and hpower=1min 255 · max 1000 Hz2
Heading accuracy3,5Typical and maximum are stated as ± values; MEMSIC proprietary software or algorithmtyp 1 · max 3 Degrees2
Sensitivity3,6,8±30 Gmin -5 · max 5 %2
Sensitivity3,6,8With16bits operationtyp 1024 counts/G2
Sensitivity3,6,8With18bits operationtyp 4096 counts/G2
Sensitivity3,6,8With 20bits operationtyp 16384 counts/G2
Sensitivity Change Over Temperature3-40~85 °C; Delta from 25 °C; ±30 G; maximum stated as ±5max 5 %2
Null Field Output8min -1 · max 1 G2
Null Field Output8With16bits operationtyp 32768 Counts2
Null Field Output8With18bits operationtyp 131072 Counts2
Null Field Output8With 20bits operationtyp 524288 Counts2
Null Field Output Change Over Temperature3Typical and maximum are stated as ± valuestyp 0.2 · max 1 mG/C2
Temperature Sensor Output3min 0.6 · typ 0.8 · max 1 C/Count2
Disturbing Field7min 32 G2
Maximum Exposed Fieldmax 10000 G2
Output Repeatability3typ 2 · max 3 mG2
Supply Voltagemin -0.5 · max 5 V4
Storage Temperaturemin -55 · max 125 C4
Maximum Exposed Fieldmax 10000 G4

Pins, by the datasheet

4
A1 VSA
Connect to ground. · p. 4
A2 SCL
I3C/I2C serial clock line. · p. 4
B1 VDD
Power supply; place a minimum 2.2 uF bypass capacitor close to this pin. · p. 4
B2 SDA
I3C/I2C serial data line. · p. 4

Ordering codes, by the datasheet

1
MMC5603NJ
WLP package · N: temperature compensated; J: RoHS compliant WLP package; tape and reel, 10000 pieces or 5000 on request per 7-inch reel. · p. 4

Open-source boards using it

28See all 28
  • 2 layers49.6 × 37.2 mmLocateMagnet, the printed circuit board in 3D

    LocateMagnet

    Aiano/LocateMagnet

    磁定位系统

    94 parts64
  • 4 layers78 × 67.5 mmUnified pcb, the printed circuit board in 3D

    Unified pcb

    starduststorm/motionhexa

    PCB designs and code for a motion-reactive, battery-powered hexagonal glowy object.

    387 parts14
  • 6 layers22.7 × 19 mmHardware V11, the printed circuit board in 3D

    Hardware V11

    mathieupommery/Keyring-GPSTRACKER

    Small gps keyring with a lot of possibilities

    71 parts5
  • 6 layers84.5 × 56 mmVLF4 PCB, the printed circuit board in 3D

    VLF4 PCB

    McMaster-Rocketry-Team/VLF4r2

    PCB schematics and layout for Void Lake Fusion 4 Avionics

    156 parts3
  • 6 layers76.5 × 69 mmFmc usb gpio spi jtag, the printed circuit board in 3D

    Fmc usb gpio spi jtag

    vowstar/rocket-pcb-orig

    FMC template board

    146 parts2Apache-2.0
  • 2 layers63.2 × 23.8 mmWand, the printed circuit board in 3D

    Wand

    ayuusweetfish/Malletwand

    A pendulum as a hands-on musical interface for all · NIME 2024 Short Paper

    68 parts1CERN-OHL-S-2.0
  • 2 layers25.4 × 25.4 mmPiicoDev Magnetometer MMC5603, the printed circuit board in 3D

    PiicoDev Magnetometer MMC5603

    CoreElectronics/CE-PiicoDev-Magnetometer-MMC5603

    This is the repo for the Core Electronics PiicoDev Magnetometer MMC5603.

    24 parts1
  • 2 layers41.2 × 10.5 mmDumb watch, the printed circuit board in 3D

    Dumb watch

    gschuk/dumb-watch

    Exercise Lab of Lecture Advanced PCB Design @ TU Darmstadt.

    61 parts1

Questions

Is there a KiCad symbol and footprint for the MMC5603NJ?

Yes. The symbol is MMC5603NJ:MMC5603NJ and the footprint wlp-4-0-82x0-82mm:WLP-4_0.82x0.82mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the MMC5603NJ?

WLP-4(0.8x0.8), with 4 pins. Its footprint is drawn on this page.

Where is the MMC5603NJ datasheet?

MEMSIC publishes it: the Datasheet link on this page opens it.

Where can I order the MMC5603NJ?

JLCPCB lists it as part C404328, with 31,401 in stock; the sellers' links on this page open their listings.

Which open-source boards use the MMC5603NJ?

28 boards in 25 repositories on GitHub; the most starred are listed on this page, with their KiCad files.