2 layers236.1 × 126.2 mm
2 layers145.9 × 153.4 mm
Gate driver
sovanaram/Power-ElectronicsCreate and experiment power conversions
- Size
- 145.9 × 153.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 166
- Nets
- 121
- Pads
- 528
- Tracks, vias
- 720, 8
- Pours
- 90
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 6 Dec 2024
- Updated
- 8 Dec 2024
Overview
Gate driver is an open-source printed circuit board by sovanaram, from the sovanaram/Power-Electronics repository on GitHub. It is a 2-layer board of 145.9 × 153.4 mm with 166 parts on 121 nets, routed with 720 tracks and 8 vias.
It is built around the IR2113S, IR2110L4 and 74HC02, with the LM7805S, 74LS04PC and 2SA1015 among its other parts. Its parts include 60 capacitors, 42 resistors, 20 connectors, 18 diodes and 12 ICs.
Main components
6
IR2113S
SOIC16WHigh And Low Side DriverInfineon TechnologiesUncategorised
IR2110L4
DIP-14DIP-14 Gate DriversInfineon TechnologiesGate Drivers74HC02
-- Logic Gates ROHSonsemiLogic Gates
LM7805S
TO-263-30℃~+125℃@(Ta) 1 1.5A 25V 2V@(1A) 40uV 5V 80dB@(120Hz) 8mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-263-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators74LS04PC
PDIP-140℃~+70℃ 4.75V~5.25V 6 6.6mA 74LS PDIP-14 InvertersonsemiInverters
2SA1015
SOT-231 PNP 100nA 130 150mA 200mW 300mV 50V 5V 80MHz PNP SOT-23 Bipolar (BJT) ROHSHXY MOSFETBipolar (BJT)
README
README.mdIsolated Pure Sine Wave Single Phase Inverter using SPWM
this topic is about How to make Inverter by your self and These are the steps to makes it: 1, Researching theories of Inverter 2, Select Topology (DCDC Converter stage, Inverter stage) 3, Calculating DCDC Converter and Inverter 4, Calculating Transformer and Inductors of DCDC Converter 5, Design Transformer and Inductors 6, Design schematic and PCB 7, Installing Hardware 8, Select electronic switches(MOSFETs and DIODEs) 9, Select Controller 10, Programming and choose the types of Closed loop Control Methods, Filter 11, Testing Hardware
Parts
166| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 104 | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C2, C4, C12, C21, C22, C25, C27, C31, C32, C33, C36, C41, C42, C45, C46, C49 +5 |
| 20 | 100 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4, R11, R12, R15, R16, R17, R18, R19, R20, R23, R24, R27, R28 +4 |
| 18 | 1N4007 | Diode_SMD:D_SMA | D1, D2, D3, D4, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +2 |
| 18 | 22p | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C5, C6, C13, C14, C15, C16, C17, C18, C19, C20, C37, C38, C39, C40, C59, C60 +2 |
| 16 | 4.7k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R13, R14, R29, R30, R31, R32, R33, R34, R35, R36, R37, R38, R39, R40, R41, R42 |
| 9 | 47uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C10, C26, C28, C30, C34, C43, C44, C51, C52 |
| 8 | 2SA1015 | PCM_Package_TO_SOT_THT_AKL:TO-92_Inline_Wide_ECB | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 6 | 10 | Resistor_SMD:R_1210_3225Metric_Pad1.30x2.65mm_HandSolder | R9, R10, R21, R22, R25, R26 |
| 6 | 100uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1, C3, C11, C29, C35, C57 |
| 6 | 1EZ12 | Diode_THT:D_DO-34_SOD68_P10.16mm_Horizontal | DZ1, DZ2, DZ3, DZ4, DZ7, DZ8 |
| 6 | 4.7uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C23, C24, C47, C48, C55, C56 |
| 5 | GDriver2 | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J5, J6, J14, J18, J20 |
| 5 | Signal IN | Connector_JST:JST_EH_B4B-EH-A_1x04_P2.50mm_Vertical | J1, J2, J9, J11, J16 |
| 4 | IR2113S | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U4, U5, U6, U11 |
| 3 | 12V GateSupply | Connector_JST:JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J7, J8, J15 |
| 3 | GDriver1 | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J13, J19, J21 |
| 2 | +5V | Connector_JST:JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J3, J4 |
| 2 | 74HC02 | PCM_Package_DIP_AKL:DIP-14_W7.62mm_LongPads | U2, U12 |
| 2 | IR2110 | Package_DIP:DIP-14_W7.62mm | U8, U10 |
| 2 | LM7805S | PCM_Package_TO_SOT_SMD_AKL:TO-252-2 | U3, U7 |
| 2 | SD | Connector_JST:JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J12, J17 |
| 1 | 74LS04 | PCM_Package_DIP_AKL:DIP-14_W7.62mm_LongPads | U1 |
| 1 | LM7805S | PCM_Package_TO_SOT_SMD_AKL:TO-263-3_TabPin2 | U9 |
Questions
How big is the Gate driver PCB?
It measures 145.9 × 153.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gate driver use?
166 parts, built around the IR2113S, IR2110L4, 74HC02 and LM7805S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gate driver KiCad files?
From the sovanaram/Power-Electronics repository on GitHub, at the commit this page was made from: the board is Gate Driver/Gate driver.kicad_pcb and its schematic Controller/Main controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gate driver design in my own project?
Its repository states no licence, so its author keeps all rights: ask sovanaram before reusing the design.
More from sovanaram/Power-Electronics
5- 2 layers102.1 × 99.8 mm
- 2 layers112.8 × 83.1 mm
- 2 layers96.7 × 59.4 mm
- 2 layers52.5 × 77.1 mm
Similar boards
- 4 layers95 × 54.4 mm
SmartVent AdvancedPCB
ishron256/TSI_SmartVent_KiCAD_May2026
This repository contains the KiCAD design documents for the TSI SmartVent project. All schematics, PCB layouts, libraries, and fabrication outputs are stored here and will be regularly updated.
48 parts - 2 layers
Nachobuck
Elias-Urquiza/taller-circuitos-tpi
Trabajo Práctico Integrador del Taller de Circuitos Electrónicos - FIUBA
19 parts - 2 layers150 × 70.2 mm
- 2 layers177 × 91.6 mm
Power Charg AUTO 12V C
Aleksei327/STM32G474-Power-Charger
Experimental STM32G474-based high-current battery charger and programmable synchronous buck converter. KiCad hardware and STM32CubeIDE firmware.
160 parts3 - 2 layers183.5 × 133 mm
- 4 layers190 × 91 mm
Inv v1
reljamar/singlePhaseInverter
A precursor project to a future three-phase inverter for driving synchronous motors
160 parts1MIT - 4 layers44 × 22 mm
Doublebridgeright v8
supernova-10/Kubits-programmable-magnets
Kubit is my Final Year Project (FYP) — a modular reconfigurable robot that uses programmable magnets, gears, and custom PCB-based control to achieve untethered actuation and reconfiguration.
32 parts1 - 2 layers107.2 × 60.3 mm
Class D Audio Amplifier
fredie1811/Class-D-Amplifier
The KiCad Schematic and PCB Layout for a Half Bridge Class-D Audio Amplifier using an MH-M28 for inputting the audio via an audio jack or via bluetooth.
35 parts