

Kompic Mk1b
Compact Open Multi-sensor Platform & Apparat.
- Size
- 44.5 × 50.6 mm
- Copper layers
- 4
- Thickness
- 1 mm
- Parts
- 149
- Nets
- 123
- Pads
- 536
- Tracks, vias
- 1,470, 288
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 29 May 2026
- Updated
- 4 Oct 2026
Overview
Kompic Mk1b is an open-source printed circuit board by porupski, from the porupski/kompic-wearable repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 44.5 × 50.6 mm with 149 parts on 123 nets, routed with 1,470 tracks and 288 vias.
It is built around the ESP32-S3-WROOM-1U-N16R8, MAX-M10S-00B and MAX30101EFD+T, with the TMP117AIDRVR, TPS62840DLCR and VEML6030 among its other parts. Its parts include 46 capacitors, 34 resistors, 15 ICs, 7 diodes and 5 connectors. It belongs with the sensors and measurement boards and the ESP32 and NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
12ESP32-S3-WROOM-1U-N16R8
SMD,19.2x18mm-103.5dBm -40℃~+65℃ 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3R8 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、I2S、JTAG、USB SMD,19.2x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesMAX-M10S-00B
LCC-18(9.7x10.1)LCC-18(9.7x10.1) GNSS Modules ROHSu-bloxGNSS ModulesMAX30101EFD+T
OLGA-14(3.3x5.6)-40℃~+85℃ 1.1mA 1.7V~2V 18bit 4 I2C Integrated ambient light cancellation (ALC)、Built-in temperature sensor OLGA-14(3.3x5.6) Heart Rate Sensors ROHSMaxim Integrated (Analog Devices)Heart Rate SensorsTMP117AIDRVR
WDFN-6-EP(2x2)-55℃~+150℃ 1.7V~5.5V 15.5ms 16bit 3.1uA Factory temperature calibration、Temperature threshold monitoring、Low-power standby、On-chip non-volatile parameter storage、On-chip digital filtering/averaging I2C、SMBus ±0.1℃ WDFN-6-EP(2x2) Temperature Sensors ROHSTexas InstrumentsTemperature SensorsTPS62840DLCR
VSON-8(1.5x2)-40℃~+125℃@(TJ) 1 1.8MHz 1.8V~3.3V 1.8V~6.5V 60nA 750mA Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Cycle-by-cycle current limiting Step-down type Yes VSON-8(1.5x2) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersVEML6030
SMD-6P,2x2mm-25℃~+85℃ 0.87mm 120klx 16bit 2.5V~3.6V 2mm 2mm I2C Light Intensity Low power/sleep mode、Spectral correction/filtering、Adjustable gain control、Interrupt/event trigger、Built-in temperature compensation SMD-6P,2x2mm Ambient Light Sensors ROHSVishay IntertechnologyAmbient Light SensorsLSM6DSV16XTR
LGA-14-40℃~+85℃ 1.71V~3.6V 2.6uA 4.5KB IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±4000dps 运动事件检测、同步与时间戳 LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometersMAX17048G+T10
DFN-8-EP(2x2)-40℃~+85℃ 1 2.5V~4.5V 3uA I2C Lithium Battery Not supported Not supported DFN-8-EP(2x2) Battery Management ROHSMaxim Integrated (Analog Devices)Battery ManagementMSM261DGT003
LGA-6(2x4)-26dB 1.1mm 1.8V 2mm 4mm 64dB 670uA Omnidirectional LGA-6(2x4) MEMS Microphones ROHSMEMSMEMS Microphones1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes2450AT18A100E
1206-40℃~+125℃ 0.5dBi 1.3mm 1.6mm 2.4GHz 2W 3.2mm 50Ω Patch Antenna SMA 1206 Antennas ROHSJohanson DielectricsAntennasEC05E1220401
SMD-30℃~+85℃ 12/12 5.5V 550uA Incremental Straight Two-phase output SMD Rotary Encoders ROHSALPSALPINERotary Encoders
README
README.mdKompic̄ · Mk1b
Compact Open Multisensor Platform & Apparatus
/ˈkompitɕ/ — Croatian for "little computer" (and the word you'd only use for an actual friend, not a stranger).
A fully open-source, offline-first, ML-capable wrist-mounted sensor platform. The hardware collects. The firmware infers. You own everything.
Internal hardware version:
iv8.0— tracked in the docs to keep the PCBs matched across revisions.
Page: https://porupski.github.io/kompic-wearable/
What it is
Kompic̄ is a wrist-mounted sensor platform built around an ESP32-S3 (dual-core, 8 MB PSRAM, 16 MB flash) with a sensor suite denser than any open-source watch, and enough on-device compute to run real neural networks on that data — sleep staging, sound classification, sensor fusion — all locally, all offline, all inspectable.
Currently on its second hardware revision, Mk1b (iv8.0): all ten I²C sensors bring up clean, the AMOLED display and touch panel run a working LVGL interface, and GPS streams live fixes.
It is not a companion in the AI sense and not a phone accessory. It runs standalone. BLE is a capability, not a requirement. There is no cloud, no subscription, no account.
Philosophy
- Open source — hardware (KiCad), firmware, ML models, and case design. Everything inspectable, modifiable, forkable.
- Offline first — works fully standalone. No phone, no cloud, no subscription.
- Raw data access — PPG waveforms, IMU streams, mic audio, environmental readings. Not just processed metrics.
- ML-native — the compute surplus exists specifically to run on-device inference.
Hardware at a glance
| Domain | Detail |
|---|---|
| MCU | ESP32-S3 dual-core Xtensa LX7 @ 240 MHz, 8 MB PSRAM, 16 MB flash |
| Storage | MicroSD (128 GB+) |
| Connectivity | BLE 5.x |
| Display | 2.06" rectangular AMOLED, 45.6 × 37.3 mm glass, QSPI |
| PCBs | Two 1.0 mm 4-layer boards: main board + skin-facing daughter board |
| Case | Two-piece SLM titanium (Ti-6Al-4V), ~48 × 40 × 12 mm |
| Weight | 33 g watch body, 56 g with straps |
| Power | ~300 mAh LiPo, USB-C charging, fuel gauge |
Sensor suite
| Sensor | Part | Measures |
|---|---|---|
| ❤️ Optical HR / SpO2 | MAX30101 | Heart rate, HRV, blood oxygen, PPG waveforms |
| 🏃 IMU | LSM6DSV16X | Accel, gyro, on-chip decision trees |
| 🔋 Fuel gauge | MAX17048G | Battery state-of-charge, cell voltage |
| 🌡️ Skin temperature | TMP117 | High-precision skin temp trending |
| 🧭 Magnetometer | LIS3MDLTR | Compass heading, magnetic anomaly |
| 🛰️ GPS | u-blox M10S | Position, velocity, atomic time sync |
| 🌍 Environmental | BME688 | Temp, pressure, humidity, VOC / air quality |
| 💡 Ambient light | VEML6030 | Lux level, display brightness |
| 🎤 MEMS microphone | MSM261DGT003 | Audio capture, noise level, sound classification |
| 📳 Haptics | ELV1411A + DRV2605L | Vibration patterns, alerts, smart wake |
| 🔦 Flashlight | White LED + BC847C driver | Utility light |
| 🚦 Status LED | RGB LED | Notification / mode indicator |
Repository layout
kompic-wearable/
├── hardware/ KiCad schematics, PCB layout, production files [CERN-OHL-S v2]
├── firmware/ ESP32-S3 dual-core firmware, ML models [GPLv3]
├── case/ Onshape / 3D-printable case models [CC BY-SA 4.0]
└── docs/ Documentation site (GitHub Pages) + images [CC BY-SA 4.0]Project status
In active development. Hardware bring-up and verification underway for Mk1b (iv8.0).
| Area | Status |
|---|---|
| Circuit + PCB | Mk1 done (schematics, power tree, KiCad source) - needs update to Mk1b |
| Fabrication + assembly | Mk1 done (JLCPCB process, BOM, production files) - needs update to Mk1b |
| Manual assembly | Planned |
| 3D models + case | Planned (View on Onshape) |
| Firmware | In progress (I²C drivers, LVGL 9 display + touch UI, GPS UBX/NMEA parsing) |
Check the Development page for info on current stage of the project.
Documentation: https://porupski.github.io/kompic-wearable/
Author & License
Hardware, firmware, case, and webpage design by Ivan Porupski, 2026.
License
Kompic̄ is released under three copyleft licenses, one per kind of material. All three keep the project open and require attribution — anyone may use, modify, build on, and even sell derivatives, provided they keep their version equally open and credit the original author.
| Part of the project | License | What it means in one line |
|---|---|---|
Hardware (/hardware) | CERN-OHL-S v2 | Make/modify/sell boards freely; distributed modifications must publish their full design files under the same license. |
Firmware (/firmware) | GPLv3 | Run/modify/redistribute freely; distributed modifications must publish full source under GPLv3. |
Docs & 3D / case (/docs, /case) | CC BY-SA 4.0 | Reuse/remix freely with credit; shared derivatives stay under CC BY-SA. |
GitHub displays GPL-3.0 as the repository's headline license; the per-folder breakdown above is authoritative. See LICENSING.md for details.
Copyright © 2026 Ivan Porupski. Each contributor retains copyright on their own contributions; the whole project remains under the copyleft licenses above.
There is no separate commercial license and no contributor license agreement (CLA). Contributions are accepted under the same licenses as the files they touch (inbound = outbound).
Contributing
Contributions are welcome. By submitting a contribution you agree it is licensed under the same license that already covers the file(s) you are changing (see table above). Keep copyright and license notices intact.
Disclaimer
Kompic̄ is not a medical device and is not intended to diagnose, treat, or prevent any condition. All work with these electronics and lithium batteries is done at your own risk. The author and contributors are not liable for any direct, indirect, incidental, or consequential damages.
Parts
149| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C16, C19, C20, C25, C26, C28, C29, C30, C31, C32, C33, C38, C39, C40, C41, C43 +3 |
| 16 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2, R4, R10, R13, R17, R20, R24, R27, R28, R30, R31, R33, R34, R35, R36 |
| 11 | 5k1 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R5, R6, R7, R8, R9, R14, R19, R21, R22, R29 |
| 9 | 10uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C3, C5, C6, C9, C11, C13, C14, C46 |
| 6 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C7, C34, C36, C37, C42, C47 |
| 5 | 4.7uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C4, C15, C22, C27, C35 |
| 3 | 1N4148WS | Diode_SMD:D_SOD-323 | D2, D3, D4 |
| 2 | 100pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C18, C21 |
| 2 | 2.2uH | Inductor_SMD:L_1008_2520Metric | L3, L5 |
| 2 | 470R | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R16, R18 |
| 2 | Net-tie | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1, JP11 |
| 2 | ST ESDALCL5-1BM2 | Diode_SMD:D_SOD-882 | D5, D6 |
| 1 | 0.22F 3.0V supercap | Kompic_Mk1b:DMS_3R3_224_supercap_feets_v1 | C17 |
| 1 | 1.0pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1 |
| 1 | 100R | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R25 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R15 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C24 |
| 1 | 2.7nH | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 2450AT18A100E | Kompic_Mk1b:ANT-SMD_L3.2-W1.6 | AE3 |
| 1 | 27nH, 5% | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | L4 |
| 1 | 3.9nH | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 33R | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R23 |
| 1 | 33k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R26 |
| 1 | 3k3 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R32 |
| 1 | 47nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10 |
| 1 | 47pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C23 |
| 1 | 50R BLE gnd | TestPoint:TestPoint_Pad_D1.0mm | TP13 |
| 1 | 50R BLE sig | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | BME688_C3664478 | Kompic_Mk1b:LGA-8_L3.0-W3.0-P0.80_BME688 | U9 |
| 1 | BQ25619RTWR | Kompic_Mk1b:WQFN-24_L4.0-W4.0-P0.50-TL-EP2.7 | U4 |
| 1 | BQ_STAT | TestPoint:TestPoint_Pad_D1.0mm | TP15 |
| 1 | BSS138W_C890266 | Kompic_Mk1b:SC-70-3_L2.0-W1.3-P0.65-LS2.1-BL | U12 |
| 1 | Ceramic GPS Antenna | Kompic_Mk1b:GPS_Ceramic_Antenna_8x8mm_v1.0 | AE1 |
| 1 | Conn_02x12_OK-14F024-04_v1 | New_Library:Connector_b2b_OK-F024-04_v1 | J1 |
| 1 | DB-Interface | Kompic_Mk1b:Custom_8_pin_for_SmartWatch_v4-DB-semicircle | J3 |
| 1 | DRV2605LDGSR | Kompic_Mk1b:VSSOP-10_L3.0-W3.0-P0.50-LS4.9-BL | U14 |
| 1 | DRV_EN | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm | JP12 |
| 1 | EC05E1220401 | Kompic_Mk1b:SW-SMD_EC05E1220401-CUSTOM-ORIENT_v1 | SW2 |
| 1 | ELV1411A | Kompic_Mk1b:Battery_solder_terminals_v1 | M1 |
| 1 | ESP32-S3-WROOM-1U-N16R8 | Kompic_Mk1b:WIRELM-SMD_ESP32-S3-WROOM-1U | U1 |
| 1 | FC31M2-32.768-NTLLLDT | Kompic_Mk1b:CRYSTAL-SMD_L3.2-W1.5-1 | X1 |
| 1 | JS16T-TYPE-C479-DWH2-FSQ | Kompic_Mk1b:USB-C-SMD_JS16T-TYPE-C479-DWH2-FSQ | USB1 |
| 1 | LIS3MDLTR | Kompic_Mk1b:LGA-12_L2.0-W2.0-P0.50-BL | U7 |
| 1 | LIS_DRDY | TestPoint:TestPoint_Pad_D1.0mm | TP19 |
| 1 | LIS_INT | TestPoint:TestPoint_Pad_D1.0mm | TP18 |
| 1 | LIS_SPI-I2C | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm | JP7 |
| 1 | LSM6DSV16XTR | Kompic_Mk1b:LGA-14_L3.0-W2.5-P0.50-BR | U5 |
| 1 | LSM_INT2 | TestPoint:TestPoint_Pad_D1.0mm | TP20 |
| 1 | LiPo 3,7V 380mAh | Kompic_Mk1b:Battery_solder_terminals_v1 | BT1 |
| 1 | M10S_RST | TestPoint:TestPoint_Pad_D1.0mm | TP21 |
| 1 | M10_SCL | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm | JP3 |
| 1 | M10_SDA | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm | JP4 |
| 1 | MAX-M10S-00B | Kompic_Mk1b:SMD-18_L10.1-W9.7-P1.10-TL_SKG09F | U6 |
| 1 | MAX17048G+T10 | Kompic_Mk1b:TDFN-8_L2.0-W2.0-P0.50-BL-EP1.2 | U3 |
| 1 | MAX30101EFD+T | Kompic_Mk1b:OESIP-14_L5.6-W3.3-P0.80-TL | U13 |
| 1 | MB Interface | Kompic_Mk1b:Custom_8_pin_for_SmartWatch_v4-MB-straightline | J2 |
| 1 | ML621 3.0V | Kompic_Mk1b:DMS_3R3_224_supercap_feets_v1 | BT2 |
| 1 | MSM261DGT003 | Kompic_Mk1b:MIC-SMD_6P-L4.0-W2.0_LMD4020T261-OC3 | U10 |
| 1 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad_TopOnly | H1 |
| 1 | NTC 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | TH1 |
| 1 | PCF85063ATL/1,118 | Kompic_Mk1b:DFN-10_L2.6-W2.6-P0.50-BL-EP | U8 |
| 1 | PMID_GOOD | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | Qvar_Electrode_1 | TestPoint:TestPoint_Pad_D3.0mm | CN2 |
| 1 | Qvar_Electrode_2 | TestPoint:TestPoint_Pad_D1.5mm | CN1 |
| 1 | RGB_DO | TestPoint:TestPoint_Pad_1.0x1.0mm | TP8 |
| 1 | SCL | TestPoint:TestPoint_Pad_1.0x1.0mm | TP11 |
| 1 | SDA | TestPoint:TestPoint_Pad_1.0x1.0mm | TP10 |
| 1 | SD_Cd | TestPoint:TestPoint_Pad_D1.0mm | TP17 |
| 1 | SKSCLBE010 | Kompic_Mk1b:KEY-SMD_4P-SKSCLXX010 | SW1 |
| 1 | Safeboot | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mm | JP2 |
| 1 | TF PUSH | Kompic_Mk1b:TF-SMD_TF-PUSH | Card1 |
| 1 | TJ-S4008SW4TGLCCW-A5 | Kompic_Mk1b:LED-SMD_TJ-S4008SW4TGLCCW-A5 | LED2 |
| 1 | TMP117AIDRVR | Kompic_Mk1b:WSON-6_L2.0-W2.0-P0.65-TL-EP | U15 |
| 1 | TMP_ALRT | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | TPD2E001DRLR | Kompic_Mk1b:SOT-553-5_L1.6-W1.2-P0.50-LS1.6-BR | D1 |
| 1 | TPS62840DLCR | Kompic_Mk1b:VSON-8_L2.0-W1.5-P0.50-BL | U16 |
| 1 | USB_D+ | TestPoint:TestPoint_Pad_D1.0mm | TP22 |
| 1 | USB_D- | TestPoint:TestPoint_Pad_D1.0mm | TP23 |
| 1 | VEML6030 | Kompic_Mk1b:SENSORS-SMD_VEML6030 | U11 |
| 1 | VEML_INT | TestPoint:TestPoint_Pad_D1.0mm | TP14 |
The 147 most common of 149 parts.
More from porupski/kompic-wearable
1- 4 layers44.5 × 50.6 mm

Similar boards
- 4 layers45 × 69 mm

OpenVault
NoctaLabs-Sh/Nocta-One-Hardware
Open hardware for the Nocta vault: an offline password manager with a 2.7 inch e-ink screen. KiCad schematic, board layout, gerbers and BOM. CERN-OHL-S v2.
64 parts1CERN-OHL-S-2.0 - 2 layers28 × 18 mm

Final project
Casasaviruz/Wearable-biosensor-PCB
A battery powered double sided PCB sensor meant to monitor the heart rate, breathing, temperature and sleep and active cycles of lab mice, made as small and non invasive as possible, data is transmitted through Bluetooth
37 parts - 6 layers53 × 80 mm

- 2 layers44.7 × 93.6 mm

- 4 layers55 × 55 mm

- 4 layers39.1 × 94.5 mm

- 4 layers70 × 90 mm

Truecolors driver
whosmatt/truecolors
110% BT.2020 Mood Light based on the Nichia NUMB12 RGB Laser Array
110 partsMIT - 4 layers15 × 30 mm

PicoRF Blk2B
madkoding/slimestuff
SlimeVR resources hub. Scripts, utilities, and complement documentation for the SlimeVR ecosystem.
67 parts
Questions
How big is the Kompic Mk1b PCB?
It measures 44.5 × 50.6 mm and has 4 copper layers, 1 mm thick.
What parts does the Kompic Mk1b use?
149 parts, built around the ESP32-S3-WROOM-1U-N16R8, MAX-M10S-00B, MAX30101EFD+T and TMP117AIDRVR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Kompic Mk1b KiCad files?
From the porupski/kompic-wearable repository on GitHub, at the commit this page was made from: the board is hardware/Kompic_Mk1b/Kompic_Mk1b.kicad_pcb and its schematic hardware/Kompic_Mk1/1_ESP32-S3_Wroom.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Kompic Mk1b design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).