Skip to the content

LSM6DSV16XTR

STMicroelectronicsExtended

-40℃~+85℃ 1.71V~3.6V 2.6uA 4.5KB IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±4000dps 运动事件检测、同步与时间戳 LGA-14(2.5x3) Accelerometers ROHS

Part id
st/LSM6DSV16XTR
Category
Accelerometers
Package
LGA-14
Pins
14
In stock
1,878 at JLCPCB (C5267406)
Used on
34 open-source boards

Overview

The LSM6DSV16XTR is an accelerometer made by STMicroelectronics in a LGA-14 package with 14 pins. -40℃~+85℃ 1.71V~3.6V 2.6uA 4.5KB IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±4000dps 运动事件检测、同步与时间戳 LGA-14(2.5x3) Accelerometers ROHS.

PCBKit's library has its KiCad symbol (Celestial_Sensor_Motion:STM LSM6DSV16X, from Altium's library) and its footprint (SparkFun-Sensor:ST_LGA-14L_2.5x3.0mm_P0.5mm_4x3, from Sparkfun-kicad), ready for a KiCad board. 1,878 are in stock at JLCPCB (part C5267406). 34 open-source boards in 27 repositories on GitHub use it.

Symbol

1SDO/SA02SDx/AH1/Qvar13SCx/AH2/Qvar24INT15VDD_IO6GND7GND8VDD9INT210OCS_AUX11SDO_AUX12CS13SCL14SDA
Celestial_Sensor_Motion:STM LSM6DSV16XFrom Altium's library

Footprint

SparkFun-Sensor:ST_LGA-14L_2.5x3.0mm_P0.5mm_4x3From Sparkfun-kicad

From the datasheet

9
Supply, least
1.71 V · Vdd, recommended operating min · p. 14
Supply, most
3.6 V · Vdd, recommended operating max · p. 14
Supply, least
1.08 V · Vdd_IO, recommended operating min · p. 14
Supply, absolute maximum
4.8 V · Vdd, absolute max · p. 19
Works from
-40 °C · Operating temperature min · p. 14
Works up to
85 °C · Operating temperature max · p. 14
Takes working
650 µA · Gyroscope and accelerometer high-performance mode, typical · p. 14
Takes asleep
2.6 µA · Gyroscope and accelerometer power-down, typical · p. 14
A pin gives at most
4 mA · Digital pin source or sink current max for guaranteed output voltage levels · p. 14

What it is and has

12
FIFO
Up to 4.5 KB · p. 1
Accelerometer full scale
±2/±4/±8/±16 g · p. 1
Gyroscope full scale
±125/±250/±500/±1000/±2000/±4000 dps · p. 1
Data processing architecture
Three channels: UI, EIS, OIS · p. 1
Motion detection
Advanced pedometer, step detector, step counter · p. 1
Motion detection
Significant motion and tilt · p. 1
Machine learning core
Exportable features and filters · p. 1
Adaptive self-configuration
Embedded ASC · p. 1
Analog hub
ADC and analog input data processing · p. 1
Sensor fusion
Embedded low-power algorithm · p. 1
Temperature sensor
Embedded · p. 1
Compliance
ECOPACK and RoHS · p. 1

Around it

1
cap 100 nF
between Vdd and GND; Recommended supply filter capacitor. · p. 11

Specifications

23
ParameterConditionsAs printedPage
Supply voltage VddT = 25 °Cmin 1.71 · typ 1.8 · max 3.6 V14
Power supply for I/O Vdd_IOVdd = 1.8 V, T = 25 °Cmin 1.08 · max 3.6 V14
Gyroscope and accelerometer current consumption in high-performance mode IddHPVdd = 1.8 V, T = 25 °Ctyp 0.65 mA14
Accelerometer current consumption in high-performance mode LA_IddHPVdd = 1.8 V, T = 25 °Ctyp 190 uA14
Accelerometer current consumption in normal mode LA_IddNMVdd = 1.8 V, T = 25 °Ctyp 100 uA14
Accelerometer current consumption in low-power mode (LPM2) LA_IddLPM2Vdd = 1.8 V, T = 25 °C, ODR = 60 Hztyp 20 uA14
Accelerometer current consumption in low-power mode (LPM2) LA_IddLPM2Vdd = 1.8 V, T = 25 °C, ODR = 1.875 Hztyp 4.2 uA14
Accelerometer current consumption in low-power mode (LPM1) LA_IddLPM1Vdd = 1.8 V, T = 25 °C, ODR = 60 Hztyp 17 uA14
Accelerometer current consumption in low-power mode (LPM1) LA_IddLPM1Vdd = 1.8 V, T = 25 °C, ODR = 1.875 Hztyp 4 uA14
Gyroscope and accelerometer current consumption during power-down IddPDVdd = 1.8 V, T = 25 °Ctyp 2.6 uA14
Turn-on time - gyroscope TonVdd = 1.8 V, T = 25 °Ctyp 30 ms14
Low-level output voltage VOLIOL = 4 mAmax 0.2 V14
Operating temperature range Topmin -40 · max 85 °C14
Power consumptionVdd_IO = 1.8 V, Zin = 235 MOhm; extra consumption when only analog hub / Qvar is enabled; accelerometer in high-performance or normal modetyp 15 uA14
Offset (shorted inputs)Vdd_IO = 1.8 V, Zin = 235 MOhmtyp 3 mV14
Noise (shorted inputs)Vdd_IO = 1.8 V, Zin = 235 MOhmtyp 54 uV14
Qvar gainVdd_IO = 1.8 V, Zin = 235 MOhmtyp 78 LSB/mV14
CMRRVdd_IO = 1.8 V, Zin = 235 MOhmtyp 54 dB14
Supply voltage Vddmin -0.3 · max 4.8 V19
Storage temperature range TSTGmin -40 · max 125 °C19
Acceleration g for 0.2 ms Sg0.2 msmax 20000 g19
Electrostatic discharge protection (HBM) ESDHBMmax 2 kV19
Input voltage on any control pin (including CS, SCL/SPC, SDA/SDI/SDO, SDO/SA0) VinRange -0.3 to Vdd_IO +0.3 Vmin -0.3 V19

Pins, by the datasheet

14
1 SDO/SA0
SPI 4-wire serial data output; I²C device address least significant bit. · p. 11
2 SDx/AH1/Qvar1
Mode 1 analog hub input 1 or Qvar electrode 1; connect to Vdd_IO or GND when disabled. Mode 2 I²C master data. Mode 3 auxiliary SPI data input and 3-wire data output. · p. 9
3 SCx/AH2/Qvar2
Mode 1 analog hub input 2 or Qvar electrode 2; connect to Vdd_IO or GND when disabled. Mode 2 I²C master clock. Mode 3 auxiliary SPI clock. · p. 9
4 INT1
Programmable interrupt in I²C and SPI. · p. 11
5 Vdd_IO
Power supply for I/O pins; recommended 100 nF filter capacitor. · p. 11
6 GND
0 V supply. · p. 11
7 GND
0 V supply. · p. 11
8 Vdd
Power supply; recommended 100 nF filter capacitor. · p. 11
9 INT2
Programmable interrupt 2 or data enable; mode 2 also supports I²C master external synchronization. · p. 11
10 OCS_Aux
Mode 3 auxiliary SPI enable; otherwise connect to Vdd_IO or leave electrically unconnected and soldered to PCB. · p. 11
11 SDO_Aux
Mode 3 auxiliary SPI 4-wire data output; leave unconnected for auxiliary 3-wire operation. In modes 1 and 2 connect to Vdd_IO or leave unconnected. · p. 11
12 CS
Interface selection: high enables I²C/MIPI I3C and SPI idle; low enables SPI communication and disables I²C/MIPI I3C. · p. 11
13 SCL
I²C/MIPI I3C serial clock or SPI serial port clock. · p. 11
14 SDA
I²C/MIPI I3C serial data, SPI serial data input, or 3-wire serial data output. · p. 11

Ordering codes, by the datasheet

2
LSM6DSV16X
LGA-14L · Tray packing; -40 to +85 °C temperature range · p. 1
LSM6DSV16XTR
LGA-14L · Tape and reel packing; -40 to +85 °C temperature range · p. 1

Open-source boards using it

34See all 34
  • 4 layers40 × 40 mmLocus, the printed circuit board in 3D

    Locus

    Nieko27/Frame-Workshop

    A repo for all things steam frame hardware.

    66 parts93CERN-OHL-S-2.0
  • 2 layers141.9 × 72.9 mmImu to dxl 10p, the printed circuit board in 3D

    Imu to dxl 10p

    jyg9/microduck-community-kit

    补充microduck缺少的硬件电路和固件,另外配套一些测试工具。imu_to_dxl;banana_pcb;microduck复刻

    897 parts28Apache-2.0
  • 6 layers26 × 25 mmTektag, the printed circuit board in 3D

    Tektag

    teklabsdigital/TekTag

    Biosensor for telehealth, patient monitoring, fall detection, dementia geofencing and cardiograms

    93 parts18
  • 4 layers44.5 × 50.6 mmKompic Mk1b, the printed circuit board in 3D

    Kompic Mk1b

    porupski/kompic-wearable

    Compact Open Multi-sensor Platform & Apparat.

    149 parts3GPL-3.0
  • 2 layers80 × 60 mmPg id656, the printed circuit board in 3D

    Pg id656

    adasbl/main-controller-pcb

    Custom PCB for an autonomous wheeled robot

    47 parts
  • 4 layers65 × 30.9 mmElec RPI Robot HAT, the printed circuit board in 3D

    Elec RPI Robot HAT

    armature-ai-labs/indieduck

    Open robot prototype: editable FreeCAD CAD, printable parts and fit-test documentation. Adapted from Open Duck Mini.

    132 partsApache-2.0
  • 4 layersImuTag, the printed circuit board in 3D

    ImuTag

    chrs89/PCBA_IMUTAG_mini

    A compact IMU tag PCB designed in KiCad.

    42 parts
  • 4 layersWatch pcb, the printed circuit board in 3D

    Watch pcb

    dezash123/watch

    Circuit board for my custom smartwatch!!!!!

    191 partsApache-2.0

Questions

Is there a KiCad symbol and footprint for the LSM6DSV16XTR?

Yes. The symbol is Celestial_Sensor_Motion:STM LSM6DSV16X and the footprint SparkFun-Sensor:ST_LGA-14L_2.5x3.0mm_P0.5mm_4x3, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the LSM6DSV16XTR?

LGA-14, with 14 pins. Its footprint is drawn on this page.

Where is the LSM6DSV16XTR datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the LSM6DSV16XTR?

JLCPCB lists it as part C5267406, with 1,878 in stock; the sellers' links on this page open their listings.

Which open-source boards use the LSM6DSV16XTR?

34 boards in 27 repositories on GitHub; the most starred are listed on this page, with their KiCad files.