Skip to the content
12345678

TPS62840DLCR

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 1.8MHz 1.8V~3.3V 1.8V~6.5V 60nA 750mA Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Cycle-by-cycle current limiting Step-down type Yes VSON-8(1.5x2) DC-DC Converters ROHS

Part id
ti/TPS62840DLCR
Category
DC DC Converters
Package
VSON-8(1.5x2)
Pins
8
In stock
3,595 at JLCPCB (C2071859)
Used on
33 open-source boards

Overview

The TPS62840DLCR is a DC DC Converter made by Texas Instruments in a VSON-8(1.5x2) package with 8 pins. -40℃~+125℃@(TJ) 1 1.8MHz 1.8V~3.3V 1.8V~6.5V 60nA 750mA Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Cycle-by-cycle current limiting Step-down type Yes VSON-8(1.5x2) DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS62849DLCR, from EasyEDA) and its footprint (Package_SON:VSON-8_1.5x2mm_P0.5mm, from KiCad's library), ready for a KiCad board. 3,595 are in stock at JLCPCB (part C2071859). 33 open-source boards in 25 repositories on GitHub use it.

Symbol

1GND2VIN3MODE4EN5VSET6STOP7SW8VOS
EasyEDA_Cloud:TPS62849DLCRFrom EasyEDA

Footprint

12345678
Package_SON:VSON-8_1.5x2mm_P0.5mmFrom KiCad's library

From the datasheet

12
Supply, least
1.8 V · VIN, recommended operating min · p. 6
Supply, most
6.5 V · VIN, recommended operating max · p. 6
Supply, absolute maximum
7 V · VIN, absolute max · p. 6
Junction, hottest
150 °C · Junction temperature, absolute max · p. 6
Takes working
60 nA · VIN, typical switching no-load current, VOUT = 1.8 V · p. 7
Takes asleep
25 nA · VIN, typical shutdown current, EN = GND · p. 7
Gives
750 mA · Rated output current max · p. 1
Current limit
1.2 A · High-side MOSFET switch current limit, typical · p. 8
Switches at
1.8 MHz · Typical, VIN = 3.6 V, VOUT = 1.8 V, MODE = VIN, IOUT = 0 mA · p. 8
Junction to air (8 Pins DLC Package)
105.6 K/W · Junction-to-ambient, JEDEC PCB 51-7 · p. 6
Junction to case (8 Pins DLC Package)
75.7 K/W · Junction-to-case top, JEDEC PCB 51-7 · p. 6
Junction to board (8 Pins DLC Package)
31.9 K/W · Junction-to-board, JEDEC PCB 51-7 · p. 6

What it is and has

6
Control
DCS-Control · p. 1
Output voltage selection
16 selectable output voltages through VSET · p. 1
Operating modes
Automatic PFM/PWM transition or forced PWM · p. 1
STOP mode
Selectable forced PWM and STOP modes · p. 1
Output discharge
Integrated output discharge · p. 1
Package options
SON-8, WCSP-6, thermally enhanced HVSSOP-8 · p. 1

Around it

4
cap 4.7-µF
between VIN and GND; Required ceramic input capacitor; place close to VIN for noise and voltage spike suppression. · p. 5
res 0.909 to 267 kΩ
between VSET and GND; External output voltage selection resistor; E96 series, 1% tolerance, temperature coefficient ±200 ppm/°C. · p. 6
ind 2.2 µH
between SW and VOUT; Nominal effective inductance; recommended effective range 1.51 to 2.9 uH. · p. 6
cap 10 µF
between VOUT and GND; Nominal effective output capacitance; recommended effective range 3 to 40 uF. Connect VOS directly to the output capacitor with a short trace. · p. 6

Specifications

65
ParameterConditionsAs printedPage
Pin voltageVIN; relative to GNDmin -0.3 · max 7 V6
Pin voltageSW (DC); maximum VIN + 0.3 Vmin -0.3 V6
Pin voltageSW (AC), less than 10ns; while switchingmin -2 · max 8.5 V6
Pin voltageEN, MODE, STOPmin -0.3 · max 6.5 V6
Pin voltageVSET; maximum stated as VIN + 0.3 < 3.6min -0.3 V6
Pin voltageVOSmin -0.3 · max 3.7 V6
Operating junction temperature TJmin -40 · max 150 °C6
Storage temperature Tstgmin -65 · max 150 °C6
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 Vmax 2000 V6
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±500 Vmax 500 V6
Supply voltage VIN VINmin 1.8 · max 6.5 V6
Effective inductance LNominal 2.2 uHmin 1.51 · typ 2.2 · max 2.9 uH6
Effective output capacitance COUTNominal 10 uFmin 3 · typ 10 · max 40 uF6
Effective input capacitance CINNominal 4.7 uFmin 1 · typ 4.7 uF6
External parasitic capacitance at VSET pin CVSETmax 100 pF6
Nominal resistance range for external voltage selection resistor (E96 resistor series) RSETmin 0.909 · max 267 kΩ6
External voltage selection resistor tolerance RSETmax 1 %6
External voltage selection resistor temperature coefficient RSET±200 ppm/°Cmax 200 ppm/°C6
Operating junction temperature range TJmin -40 · max 125 °C6
Junction-to-ambient thermal resistance RθJA8 Pins DLC Package; JEDEC PCB 51-7typ 105.6 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)8 Pins DLC Package; JEDEC PCB 51-7typ 75.7 °C/W6
Junction-to-board thermal resistance RθJB8 Pins DLC Package; JEDEC PCB 51-7typ 31.9 °C/W6
Junction-to-top characterization parameter ψJT8 Pins DLC Package; JEDEC PCB 51-7typ 2.3 °C/W6
Junction-to-board characterization parameter ψJB8 Pins DLC Package; JEDEC PCB 51-7typ 31.5 °C/W6
No load operating input current IQ_NO_LOADVIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.8V, device switching; typical at TJ = 25°Ctyp 60 nA7
No load operating input current IQ_NO_LOADVIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.2V, device switching; typical at TJ = 25°Ctyp 80 nA7
No load operating input current (PWM Mode) IQ_NO_LOADVIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.8V, MODE = VIN, device switching; typical at TJ = 25°Ctyp 3 mA7
Operating quiescent current into pin VIN IQ_VINDLC package option; VIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.55V or 1.8V, device not switching, TJ = 25°Ctyp 36 · max 100 nA7
Operating quiescent current into pin VOS IQ_VOSDLC package option; VIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.55V or 1.8V, device not switching, TJ = 25°Ctyp 56 · max 120 nA7
Operating quiescent current into pin VIN IQ_VINVIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.55V or 1.8V, device not switching, TJ = -40°C to 85°Ctyp 36 · max 360 nA7
Operating quiescent current into pin VOS IQ_VOSVIN = 3.6 V, EN = VIN, IOUT = 0uA, VOUT = 1.55V or 1.8V, device not switching, TJ = -40°C to 85°Ctyp 56 · max 170 nA7
Operating quiescent current into VOS pin IQ_VOSVIN = 3.6 V, EN = VIN, VOUT = 3.3V, device not switching; typical at TJ = 25°Ctyp 70 nA7
Operating quiescent current into VOS pin IQ_VOSVIN = 3.6 V, EN = VIN, VOUT < 1.5 V, device not switching; typical at TJ = 25°Ctyp 5 nA7
Operating quiescent current into VOS pin IQ_VOSVIN = 3.6 V, EN, STOP = VIN, 3V < VOUT < 3.3V, TJ = -40°C to 85°Ctyp 5 · max 100 nA7
Operating quiescent current 100% Mode IQ_100%_MODEVIN = VOUT = 3.3V, TJ = -40°C to 85°Ctyp 120 nA7
Operating quiescent current into pin VIN IQ_VIN_STOPVIN = 3.6 V, STOP = High, VOUT = 1.8V, TJ = -40°C to 85°Ctyp 70 · max 175 uA7
Shutdown current ISDVIN = 3.6 V, EN = GND, shutdown current into VIN, VSET = GND, TJ = -40°C to 85°Ctyp 25 · max 300 nA7
Undervoltage lockout threshold VTH_UVLO+Rising VINtyp 1.72 · max 1.8 V7
Undervoltage lockout threshold VTH_UVLO–Falling VINtyp 1.45 · max 1.75 V7
High level input voltage VIH_THEN, MODE, STOP inputsmin 1.1 V7
Low level input voltage VIL_THEN, MODE, STOP inputsmax 0.4 V7
Input bias current IINMODE input, TJ = -40°C to 85°Ctyp 1 · max 25 nA7
Internal pull-down resistance RPDEN, STOP inputsmin 200 · typ 450 kΩ7
High-side MOSFET on-resistance RDS(ON)DLC package; VIN = 3.6V, I = 200mA, TJ = -40°C to 85°Ctyp 430 · max 600 mΩ8
High-side MOSFET on-resistance RDS(ON)DLC package; VIN = 5V, I = 200mA, TJ = -40°C to 85°Ctyp 340 · max 465 mΩ8
Low-side MOSFET on-resistance RDS(ON)DLC package; VIN = 3.6V, I = 200mA, TJ = -40°C to 85°Ctyp 170 · max 240 mΩ8
Low-side MOSFET on-resistance RDS(ON)DLC package; VIN = 5V, I = 200mA, TJ = -40°C to 85°Ctyp 135 · max 180 mΩ8
Soft-start switch current limit ILIMF_SSStatic current limit; VIN = 3.6 Vmin 0.15 · typ 0.225 · max 0.3 A8
High-side MOSFET switch current limit ILIMFStatic current limit; VIN = 3.6 Vmin 1 · typ 1.2 · max 1.4 A8
Low-side MOSFET switch current limit ILIMFVIN = 3.6 Vtyp 1 A8
Negative current limit ILIMNVIN = 3.6 Vtyp 533 mA8
Current limit propagation delay tI_LIM_DELAYVIN = 3.6 Vtyp 50 ns8
Leakage current into SW pin ILKG_SWVSW = 1.8V, TJ = -40°C to 85°Ctyp 10 nA8
Output discharge current IDISCHARGE_VOSEN = GND, sink current into VOS pin, over VIN range, VOUT = 1.8V, TJ = -40°C to 85°Cmin 16 · typ 35 · max 44 mA8
Thermal shutdown temperature TSDRising junction temperature, PWM Modetyp 160 °C8
Thermal shutdown hysteresis TSDtyp 5 °C8
Output voltage accuracy VOUTPWM Mode, IOUT = 0 mA, VOUT >= 1.8 Vmin -1.5 · typ 0 · max 1.5 %8
Output voltage accuracy VOUTPWM Mode, IOUT = 0 mA, VOUT <= 1.55 Vmin -2 · typ 0 · max 2 %8
DC output voltage load regulation VOUTPWM Modetyp 0 %/mA8
DC output voltage line regulation VOUTPWM Mode, VOUT = 1.8V, IOUT = 200 mA, over VIN rangetyp 0 %/V8
Switching frequency fSWVIN = 3.6V, VOUT = 1.8V, MODE = VIN, IOUT = 0mAtyp 1.8 MHz8
Regulator start up delay time tSTARTUP_DELAYVIN = 3.6V, from EN = low to high until device starts switchingmax 200 us8
Regulator start up delay time tSTARTUP_DELAYEN ramps with VIN, VIN 0 to 3.6V (< 100us), until device starts switchingtyp 10 ms8
Soft-start time tSSIOUT = 0mAtyp 120 us8
Reduced current limit soft-start timeout tSS_ILIMFtyp 700 · max 1200 us8

Pins, by the datasheet

8
1 GND
Ground supply pin; connect close to the ground terminals of the input and output capacitors. · p. 5
2 VIN
Input supply; place the required 4.7-uF ceramic input capacitor close to this pin. · p. 5
3 MODE
Low selects Power-Save Mode with automatic PFM/PWM transition; high forces PWM; must be terminated. · p. 5
4 EN
High enables operation and low turns the device off; internal pulldown is disabled after startup and regulation and reactivated after a low level. · p. 5
5 VSET
Connect a resistor to ground to select the output voltage when enabled. · p. 5
6 STOP
High stops switching while the output capacitor supplies the load; low immediately resumes operation; internal pulldown is disabled after a high level and reactivated after a low level. · p. 5
7 SW
Switch node connected to the internal MOSFET switches; connect the inductor here. · p. 5
8 VOS
Output voltage sense for feedback and regulation; connect directly to the output capacitor with a short trace; discharges the output through an internal MOSFET when disabled. · p. 5

Open-source boards using it

33See all 33
  • 2 layers36.4 × 29.4 mmKicad Smart Watch, the printed circuit board in 3D

    Kicad Smart Watch

    AFLProjects/DIY-Smart-Watch

    DIY Smart Watch with ATMEGA32U4 , ST7789 SPI display and RV3028-C7 Extreme Low Power RTC Module

    63 parts12
  • 2 layers15.2 × 31.1 mmOlmBoard v1, the printed circuit board in 3D

    OlmBoard v1

    azerimaker/olmBoard

    This is a TPS62840 based, highly-efficient, breadboard-friendly buck converter

    25 parts8MIT
  • 2 layers55.6 × 57.2 mmYkb skadi pcb, the printed circuit board in 3D

    Ykb skadi pcb

    YarmanKB/ykb-skadi-pcb

    KiCad project for YKB Skadi boards

    74 parts7Apache-2.0
  • 2 layers62 × 30 mmECG, the printed circuit board in 3D

    ECG

    NguyenThanhHuy-debug/PCB_IoT-Heart-rate-ECG-Monitoring-Device

    The PCBIoT-Heart-rate-ECG-Monitoring-Device repository provides open-source hardware design files for an IoT-enabled electrocardiogram (ECG) and heart-rate monitoring device.

    100 parts4
  • 6 layers51 × 65 mmOwo, the printed circuit board in 3D

    Owo

    hydrastro/owo

    uwu

    135 parts3
  • 4 layers89 × 54 mmOBCProto, the printed circuit board in 3D

    OBCProto

    Kmshanley/PicoSat-Initiative

    The pocket cube standard requires satellites to be 5x5x5cm and under 250 grams. Upon completion of this Wentworth PicoSat it will become one of the smallest satellites capable of high resolution imagery from LEO.

    126 parts3GPL-3.0
  • 4 layers12 × 20 mmRing, the printed circuit board in 3D

    Ring

    OlinSTEP/step-devices

    STEP Monorepo

    39 parts3
  • 4 layers44.5 × 50.6 mmKompic Mk1b, the printed circuit board in 3D

    Kompic Mk1b

    porupski/kompic-wearable

    Compact Open Multi-sensor Platform & Apparat.

    149 parts3GPL-3.0

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the TPS62840DLCR?

Yes. The symbol is EasyEDA_Cloud:TPS62849DLCR and the footprint Package_SON:VSON-8_1.5x2mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS62840DLCR?

VSON-8(1.5x2), with 8 pins. Its footprint is drawn on this page.

Where is the TPS62840DLCR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS62840DLCR?

JLCPCB lists it as part C2071859, with 3,595 in stock; the sellers' links on this page open their listings.

What can replace the TPS62840DLCR?

Parts like it in the library: the TPS62841DLCR by Texas Instruments and the TPS62849DLCR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS62840DLCR?

33 boards in 25 repositories on GitHub; the most starred are listed on this page, with their KiCad files.