
Cloudfridge
plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.
Pwmcontroller is an open-source printed circuit board by plantalytix, from the plantalytix/hardware repository on GitHub. It is a 2-layer board of 78.2 × 106.2 mm with 67 parts on 56 nets, routed with 356 tracks and 271 vias.
It is built around the ESP32-WROVER-E(4MB), 1N4148W and SMBJ7.0A. Its parts include 22 resistors, 18 capacitors, 5 connectors, 4 diodes and 3 ICs. It belongs with the ESP32 boards of this library.
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.
USB-C Programming adapter for all plantalyix devices. Used to flash firmware directly onto the device using the RJ12 connector on the device
Fridgegrow 2.0, multiple boards.
Controller for EC Fans
Controller for dimmable LED lights
Smart socket
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 0.1UF 25V | Capacitor_SMD:C_0402_1005Metric | C6, C7, C8, C9, C10, C11, C12, C14, C17, C18 |
| 10 | 100k | Resistor_SMD:R_0402_1005Metric | R2, R3, R4, R5, R6, R7, R15, R16, R17, R22 |
| 10 | 1k | Resistor_SMD:R_0402_1005Metric | R8, R9, R10, R11, R12, R13, R18, R19, R20, R21 |
| 8 | MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965 | H1, H2, H3, H4, H5, H6, H7, H8 |
| 3 | Screw_Terminal_01x03 | TerminalBlock:TerminalBlock_bornier-3_P5.08mm | J1, J4, J5 |
| 2 | 1N4148W | Diode_SMD:D_SOD-123 | D2, D3 |
| 2 | 1n 440v | Capacitor_THT:C_Disc_D7.5mm_W2.5mm_P5.00mm | C1, C3 |
| 2 | 47pf | Capacitor_SMD:C_0402_1005Metric | C15, C16 |
| 1 | 1.2MH 300MA 4 OHM | Inductor_THT:L_Radial_D8.7mm_P5.00mm_Fastron_07HCP | L1 |
| 1 | 100n 310V | Capacitor_THT:C_Rect_L13.0mm_W8.0mm_P10.00mm_FKS3_FKP3_MKS4 | C13 |
| 1 | 10u 440V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C2 |
| 1 | 12 OHM 5% 3W | Resistor_THT:R_Axial_DIN0414_L11.9mm_D4.5mm_P15.24mm_Horizontal | R1 |
| 1 | 12v | Diode_SMD:D_SOD-123 | D4 |
| 1 | 150u 25v | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C5 |
| 1 | 2M | Resistor_SMD:R_1206_3216Metric | R14 |
| 1 | 4.7UH 2.5A 30 MOHM | Inductor_THT:L_Radial_D9.5mm_P5.00mm_Fastron_07HVP | L2 |
| 1 | 470u 6v3 | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C4 |
| 1 | 7A | Fuse:Fuse_2512_6332Metric | F1 |
| 1 | ESP32-WROVER-E | Espressif:ESP32-WROVER-E | U1 |
| 1 | LOGO | fridgegrow:logo | l3 |
| 1 | LS03-13B03R3 | flexogrow:LS03-13B03R3 | PS1 |
| 1 | RJ12 | flexogrow:RJ12_VERT | J2 |
| 1 | RotaryEncoder_Switch | Rotary_Encoder:RotaryEncoder_Bourns_Vertical_PEC12R-3xxxF-Sxxxx | SW1 |
| 1 | SFH 3710-Z | LED_SMD:LED_0805_2012Metric | Q2 |
| 1 | SMBJ7.0A | Diode_SMD:D_SMB | D1 |
| 1 | Screw_Terminal_01x04 | TerminalBlock:TerminalBlock_bornier-4_P5.08mm | J3 |
| 1 | TLV272IS-13 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | ssd1306 | flexogrow:ssd1306 | U2 |

plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

plantalytix/hardware
Hardware design documents for all plantalytix products. Created using KiCAD version 5 and 6.

zachrjt/digital-voltages-ps
Fixed 3.3V and 5V voltage power supply with voltage and current readout

bungernut/ESP32BrewRIMS
Preferred version is the WebApp. where ESP32 hosts a webserver that allows someone on the same network to enable heater or change set-point.




o7-machinehum/wifiwart
Linux SBC featuring two wifi radios, masquerading as a USB charger.


It measures 78.2 × 106.2 mm and has 2 copper layers, 1.6 mm thick.
67 parts, built around the ESP32-WROVER-E(4MB), 1N4148W and SMBJ7.0A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the plantalytix/hardware repository on GitHub, at the commit this page was made from: the board is plantalytix-fan/pwmcontroller.kicad_pcb and its schematic plantalyitx-programmer/fg_programmer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask plantalytix before reusing the design.