Skip to the content
2 layers47 × 86.9 mmPicoLume, the printed circuit board in 3D

Hardware designs for the PicoLume wireless LED prop system. All designs are created in KiCad.

Size
47 × 86.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
71
Nets
82
Pads
309
Tracks, vias
684, 129
Pours
6
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
5 Dec 2025
Updated
11 Aug 2026

Overview

PicoLume is an open-source printed circuit board by picolume, from the picolume/hardware repository on GitHub, published under the MIT licence. It is a 2-layer board of 47 × 86.9 mm with 71 parts on 82 nets, routed with 684 tracks and 129 vias.

It is built around the RP2040, 74AHCT1G125SE and AP63203WU, with the AP63205WU, W25Q128JVSIQ and SI2371EDS among its other parts. Its parts include 20 capacitors, 15 resistors, 9 connectors, 6 ICs and 5 switches. It belongs with the RP2040 boards of this library.

Main components

9

README

README.md

PicoLume Hardware

Hardware designs for the PicoLume wireless LED prop system. All designs are created in KiCad.

Design Series

series-prop (Primary)

The primary hardware design for production use. Contains the PicoLume Board - a compact control board designed to be installed on each prop in a synchronized LED light show.

Current Design: receiver-v1

An RP2040-based control board featuring:

  • RP2040 microcontroller with 16MB flash (W25Q16JVS)
  • RFM69HCW radio module (915 MHz) for wireless timecode reception
  • USB-C connector for programming and show file upload
  • Dual power input with automatic switching (LM66200)
  • 5V buck converter (AP63205WU) for LED strip power
  • Pinout for 0.91" OLED display (I2C)
  • Screw terminals for LED strip connection (WS2812B)
  • Level shifter (74AHCT1G125) for reliable LED data signal
  • Three tactile buttons for configuration
  • Onboard WS2812B status LED
  • Four M3 mounting holes

The PicoLume Board is the core control component. A complete receiver or transmitter setup requires additional hardware (enclosures, power supplies, antennas, etc.) which are currently being designed.

series-legacy (Prototypes)

Early prototype designs from the development phase. These boards were used for proof-of-concept testing and firmware development.

Note: These designs are prototypes and are not suited for production use.

VersionDescription
v1Initial RFM69-based design
v2RP2040 with Pi Pico footprint
v3Refined RP2040 design
v4RP2350 Experiment

Related Repositories

  • firmware/ - Arduino firmware for receiver and remote devices

License

See LICENSE for details.

Parts

71
QtyValueFootprintReferences
11100nCapacitor_SMD:C_0603_1608MetricC5, C6, C7, C9, C11, C12, C13, C14, C15, C16, C19
810kResistor_SMD:R_0603_1608MetricR6, R7, R8, R9, R10, R11, R12, R14
4MountingHoleMountingHole:MountingHole_2.7mm_M2.5H1, H2, H3, H4
4SW_Push2_Pin_Button:FSMHSW1, SW2, SW3, SW4
310uCapacitor_SMD:C_0603_1608MetricC1, C17, C18
21kResistor_SMD:R_0603_1608MetricR1, R5
21uCapacitor_SMD:C_0603_1608MetricC8, C10
222pCapacitor_SMD:C_0603_1608MetricC2, C3
222uCapacitor_SMD:C_0603_1608MetricC4, C20
227Resistor_SMD:R_0603_1608MetricR3, R4
24.7uInductor_Mouser:VLS5045EX330ML1, L2
2Conn_01x18_PinConnector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_VerticalJ1, J3
2LOGOLOGOG***, G***
2Si2371EDSPackage_TO_SOT_SMD:SOT-23Q3, Q4
1100kResistor_SMD:R_0603_1608MetricR13
110KResistor_SMD:R_0603_1608MetricR2
1208-8Dip_Switch:2088S1
1470Resistor_SMD:R_0603_1608MetricR15
174AHCT1G125Pico_RF_V1:SOT-25U6
1AP63203WUPackage_TO_SOT_SMD:TSOT-23-6U1
1AP63205WUPackage_TO_SOT_SMD:TSOT-23-6U5
1Conn_01x01_PinConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ5
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1Conn_01x04_PinConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ4
1Conn_CoaxialConnector_Coaxial:U.FL_Molex_MCRF_73412-0110_VerticalJ8
1Crystal_GND2412_Crystal:ABM810000MHZ12D2WY1
1DDiode_SMD:D_0603_1608MetricD2
1GSB1C41110SSHRUSB_C:GSB1C41110SSHRJ9
1LEDLED_SMD:LED_0603_1608MetricD1
1PolyfuseFuse:Fuse_1210_3225MetricF3
1RFM69HCWRFM69:MOD_COM-13909U4
1RP2040RP2040_minimal:RP2040-QFN-56U3
1SS38Diode_SMD:D_SMAD4
1Screw_Terminal_01x02TerminalBlock:TerminalBlock_bornier-2_P5.08mmJ6
1Screw_Terminal_01x03TerminalBlock:TerminalBlock_bornier-3_P5.08mmJ7
1W25Q128JVSPackage_SO:SOIC-8_5.23x5.23mm_P1.27mmU2
1WS2812BLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD3

More from picolume/hardware

3
  • 4 layers47 × 90 mmPicoLume v4, the printed circuit board in 3D

    PicoLume v4

    picolume/hardware

    Hardware designs for the PicoLume wireless LED prop system. All designs are created in KiCad.

    102 partsMIT
  • 2 layers47 × 84.9 mmRemote v0.1.0, the printed circuit board in 3D

    Remote v0.1.0

    picolume/hardware

    Hardware designs for the PicoLume wireless LED prop system. All designs are created in KiCad.

    70 partsMIT
  • 2 layers47 × 84.9 mmReceiver v0.1.0, the printed circuit board in 3D

    Receiver v0.1.0

    picolume/hardware

    Hardware designs for the PicoLume wireless LED prop system. All designs are created in KiCad.

    69 partsMIT

Similar boards

  • 2 layers120 × 102.5 mmDsug cctv BOARD, the printed circuit board in 3D

    Dsug cctv BOARD

    LucasLHenry/spelltwister

    This is the third version of the code for the Spelltwister module with CCTV. This version uses the Arduino platform and the RP2040, a chip developed by Raspberry Pi for their RPi Pico board.

    251 partsMIT
  • 4 layers68.6 × 21 mmPico poe, the printed circuit board in 3D

    Pico poe

    rm-1n/conduit

    poe microcontroller with web IDE + firmware upload

    76 partsMIT
  • 4 layers96 × 60 mmMainboard-2023, the printed circuit board in 3D

    Mainboard-2023

    luhbots/luhsoccer_electronics

    The eletronics projects of our robots and basestation.

    212 parts2
  • 4 layers51.8 × 68.3 mmButton Matrix RP2040, the printed circuit board in 3D

    Button Matrix RP2040

    hazenluk/RP2040_AS3394

    An AS3394 Voice Card with built in RP2040

    229 parts3
  • 2 layers158.8 × 100.2 mmChocobanan rev.1, the printed circuit board in 3D

    Chocobanan rev.1

    leonrat/Chocobanan

    An alice-like 40% split keyboard

    108 parts1
  • 4 layers70 × 68 mmSssata fluxpad Fluxpad, the printed circuit board in 3D

    Sssata fluxpad Fluxpad

    punkfab/pcb-corpus

    235 real KiCad boards from open-source hardware repositories, prepared as a placement and routing benchmark

    78 parts1
  • 4 layers71.8 × 40.1 mmRoomba, the printed circuit board in 3D

    Roomba

    trhussain/trhussain.github.io

    65 parts1
  • 4 layers85.4 × 106.8 mmBioSense, the printed circuit board in 3D

    BioSense

    KrystianRuszczak/BioSense

    The hardware design files in this directory are licensed under CERN-OHL-P-2.0. See LICENSE.

    92 partsMIT

Questions

How big is the PicoLume PCB?

It measures 47 × 86.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PicoLume use?

71 parts, built around the RP2040, 74AHCT1G125SE, AP63203WU and AP63205WU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PicoLume KiCad files?

From the picolume/hardware repository on GitHub, at the commit this page was made from: the board is series-legacy/v3/PicoLume.kicad_pcb and its schematic series-legacy/v2/Pi_Pico_RFM69_Controller/Pi_Pico_RFM69_Controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PicoLume design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).