

Bootloader to initialise MS3 if you need to replace the HCS12
- Size
- 83.4 × 68.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 82
- Nets
- 123
- Pads
- 453
- Tracks, vias
- 1,390, 166
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 14 Oct 2018
- Updated
- 15 Feb 2022
Overview
Ms3 is an open-source printed circuit board by pggood, from the pggood/Megasquirt-MS3-Bootloader repository on GitHub. It is a 4-layer board of 83.4 × 68.5 mm with 82 parts on 123 nets, routed with 1,390 tracks and 166 vias.
It is built around the MC9S12XDP512CAG, MCP2551-I/SN and FT232RL, with the 74HC00D among its other parts. Its parts include 30 resistors, 29 capacitors, 6 ICs, 5 diodes and 3 connectors.
Main components
4MC9S12XDP512CAG
LQFP-144(20x20)10bit 119 2.35V~5.5V 512KB 80MHz FLASH HCS12X LQFP-144(20x20) Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)MCP2551-I/SN
SOIC-8-40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver SOIC-8 CAN Transceivers ROHSMicrochip TechnologyCAN TransceiversFT232RL
SSOP-28-208mil-40℃~+85℃ 3.3V~5.25V、4V~5.25V USB 2.0 USB to UART SSOP-28-208mil USB Converters ROHSFTDIUSB Converters74HC00D
SOP-14-40℃~+125℃ 1.5V、3.15V、4.2V 1.9V、3.7V、5.9V 100mV、400mV、400mV 2 2V~6V 4 40uA 5.2mA 5.2mA 500mV~1.8V 74HC Series 7ns@6V,50pF NAND Gate SOIC-14 Logic Gates ROHSNexperiaLogic Gates
Parts
82| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 1K | SM0603 | R5, R6, R7, R9, R10, R22, R23, R24, R26, R28 |
| 7 | 10K | SM0603 | R3, R14, R15, R16, R18, R20, R27 |
| 4 | .1 | c_0603 | C3, C4, C6, C20 |
| 4 | .1uF | c_0603 | C12, C13, C14, C100 |
| 4 | 470 | SM0603 | R17, R19, R25, R29 |
| 3 | 1uF | c_0603 | C23, C26, C27 |
| 3 | 4K7 | SM0603 | R1, R2, R21 |
| 3 | DIODE | sot23 | D1, D2, D4 |
| 2 | .2uF | c_0603 | C17, C19 |
| 2 | 1.5uF | c_0603 | C8, C10 |
| 2 | 1nF | c_0603 | C5, C11 |
| 2 | 2N7002 | sot23_v2 | Q1, Q2 |
| 2 | 50pF | c_0603 | C16, C18 |
| 2 | 55nF | c_0805 | C7, C9 |
| 2 | 90nF | c_0603 | C2, C21 |
| 2 | DIODE | SM2010 | D3, D5 |
| 2 | JUMPER | PINHEAD1-2 | JP4, JP6 |
| 1 | 1 OHM | SM2010 | R4 |
| 1 | 100N | c_0603 | C25 |
| 1 | 10M | SM0603 | R12 |
| 1 | 10k | SM0603 | R30 |
| 1 | 10nF | c_0603 | C15 |
| 1 | 120 | SM1206 | R8 |
| 1 | 185nF | c_0603 | C22 |
| 1 | 186nF | c_0603 | C24 |
| 1 | 1OHM | SM2010 | R11 |
| 1 | 330 | SM0805 | R13 |
| 1 | 4.5uF | c_2220 | C1 |
| 1 | 4.7uF | c_1808 | C28 |
| 1 | 74HC00 | SOP14 | U2 |
| 1 | 8mHz | crystal_hc-49u | X1 |
| 1 | A4970 | SOICW24 | U4 |
| 1 | B/LD | PINHEAD1-2 | JP3 |
| 1 | CONN_3X2 | pin_array_3x2 | JP1 |
| 1 | CONN_5X2 | PIN_ARRAY_5x2 | P1 |
| 1 | Expansion connector | pin_array_17x2 | JP2 |
| 1 | FT232RL | SSOP28 | U6 |
| 1 | LD1117LD33C | SSOP8 | U5 |
| 1 | MC9S12XDP512 | PQFP112 | U1 |
| 1 | MCP2551-I/SN | SO8E | U3 |
| 1 | SD | SDCARDmolex130203a | J1 |
| 1 | SUPP40 | DIP-40__600 | JP5 |
| 1 | USB_B | USB_B | J2 |
Similar boards
- 4 layers25.4 × 68.6 mm

- 2 layers353.1 × 101.6 mm

ATMEGA16M1 panel
brandon-martinez/jgb
The microcontroller present on this board, and the software which runs on it should eventually be integrated into each node which must communicate via the CAN bus.
195 parts - 2 layers49.5 × 111.8 mm

Universal can board
franc0r/universal_can_board
Contains schematic, pcb layout and software of the francor's universal can board.
70 partsBSD-3-Clause - 2 layers127 × 127 mm

- 2 layers68 × 31 mm

- 2 layers109 × 95 mm

- 2 layers140 × 178.7 mm

- 2 layers256.5 × 172.9 mm

Questions
How big is the Ms3 PCB?
It measures 83.4 × 68.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Ms3 use?
82 parts, built around the MC9S12XDP512CAG, MCP2551-I/SN, FT232RL and 74HC00D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ms3 KiCad files?
From the pggood/Megasquirt-MS3-Bootloader repository on GitHub, at the commit this page was made from: the board is circuit/ms3.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ms3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask pggood before reusing the design.