

Universal can board
Contains schematic, pcb layout and software of the francor's universal can board.
- Size
- 49.5 × 111.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 86
- Pads
- 265
- Tracks, vias
- 123, 8
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 15 Jan 2018
- Updated
- 6 Oct 2018
Overview
Universal can board is an open-source printed circuit board by franc0r, from the franc0r/universal_can_board repository on GitHub, published under the BSD-3-Clause licence. It is a 2-layer board of 49.5 × 111.8 mm with 70 parts on 86 nets, routed with 123 tracks and 8 vias.
It is built around the ATMEGA328P-AU, MCP2551-I/SN and FT232RL, with the LM1117-3.3, MCP2515-I/ST and BAT54S among its other parts. Its parts include 24 resistors, 20 capacitors, 14 diodes, 5 ICs and 5 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MCP2551-I/SN
SOIC-8-40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver SOIC-8 CAN Transceivers ROHSMicrochip TechnologyCAN TransceiversFT232RL
SSOP-28-208mil-40℃~+85℃ 3.3V~5.25V、4V~5.25V USB 2.0 USB to UART SSOP-28-208mil USB Converters ROHSFTDIUSB ConvertersLM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedMCP2515-I/ST
TSSOP-20-40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI TSSOP-20 CAN Controllers ROHSMicrochip TechnologyCAN ControllersBAT54S
SOT-231 Pair Series Connection 1V@100mA 200mA 2uA@25V 30V 600mA SOT-23 Schottky Diodes ROHSMDDSchottky DiodesB2100-13-F(MS)
SMBSchottky DiodesMSKSEMI
README
README.mduniversal_can_board
Contains schematic, pcb layout and software of the francor's universal can board.
Description
The universal board is used to control and monitor several components of a mobile robot like the motor controllers, co2 sensors, pan tilt unit, etc...
The board communicates via CAN interface. The used µC is a AVR from the Arduino Nano v2. Future more this board is based on an Arduino, so the Arduino IDE can be used to programm the board.
Requirements
Motor Controller
The BLD300B motor controller is used to drive the Robot Morty. This controller must be controlled and monitored by the board. For this following inputs and outputs are required.
- Input
- An analog to measure current voltage of the motor controller.
- An analog to measure current current of the motor controller.
- Three digital to get the hall sensors of the hub motor wheels.
- An digital to get the speed ticks from the motor controller.
- Output
- An PWM to set the motor power.
- An digital to set the rotation direction.
- An digital to enable/disable the break.
- An digital to enable/disable the motor controller.
CO2 Sensor
The universal board should be able to measure the CO2 sensor and publish the values via CAN.
-
Input
- An analog to measure the current CO2 concentration.
-
Output
- An digital to indicate a high CO2 concentration. (drive a LED).
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100n | Capacitors_SMD:C_0805 | C1, C3, C4, C5, C22, C23, C24, C25 |
| 8 | 10n | Capacitors_SMD:C_0805 | C10, C12, C13, C15, C16, C17, C18, C19 |
| 8 | 2k2 | Resistors_SMD:R_0805 | R7, R8, R9, R10, R11, R12, R13, R14 |
| 8 | 560R | Resistors_SMD:R_0805 | R17, R18, R19, R20, R21, R22, R23, R24 |
| 8 | BAT54S | TO_SOT_Packages_SMD:SOT-23 | D5, D6, D7, D8, D9, D10, D11, D12 |
| 7 | 1k | Resistors_SMD:R_0805 | R1, R2, R3, R4, R5, R6, R15 |
| 3 | B2100-13-F | Diodes_SMD:SMB_Standard | D4, D13, D14 |
| 3 | LED | LEDs:LED_0805 | D1, D2, D3 |
| 2 | 4u7 | Capacitors_SMD:C_1210 | C9, C20 |
| 2 | ABM3B_16M | Crystals:Crystal_SMD_5032_4Pads | Y1, Y2 |
| 2 | CONN_01X08 | Connector_RJ:RJ45_8 | P4, P5 |
| 1 | 10u | Capacitors_SMD:C_1210 | C21 |
| 1 | 120R | Resistors_SMD:R_0805 | R16 |
| 1 | 1u | Capacitors_SMD:C_0805 | C2 |
| 1 | ATMEGA328P-A | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | IC1 |
| 1 | CONN_01X02 | Connectors_Phoenix:PhoenixContact_MSTBVA-G_02x5.08mm_Vertical | P3 |
| 1 | CONN_01X08 | Connectors_Phoenix:PhoenixContact_MSTBVA-G_08x5.08mm_Vertical | P2 |
| 1 | FT232RL | Housings_SSOP:SSOP-28_5.3x10.2mm_Pitch0.65mm | U1 |
| 1 | LM1117-3.3 | TO_SOT_Packages_SMD:SOT-223 | U2 |
| 1 | MCP2515-I/ST | Housings_SSOP:TSSOP-20_4.4x6.5mm_Pitch0.65mm | U3 |
| 1 | MCP2551-I/SN | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U4 |
| 1 | USB_OTG | Connector_USB:USB_Mini-B_Lumber_2486_Horizontal | P1 |
Similar boards
- 4 layers137.2 × 61.6 mm

- 4 layers128.4 × 70.8 mm

VCU3.0
Obili69/E-GoCart
Vehicle Control Unit (VCU) firmware for an electric go-kart, built on ESP32-S3 with FreeRTOS. Manages motor control, battery management, charging, telemetry, and safety systems over dual CAN buses.
109 parts - 2 layers157 × 58.5 mm

- 4 layers85 × 50 mm

- 2 layers45 × 49.8 mm

CCCCPPPS MkI
BogdanTheGeek/CCCCPPPS
Cheap Crappy Constant Current Portable Programmable Power Supply
26 parts12MIT - 4 layers149.2 × 108 mm

Opensyringepump indus
PySpice-org/eda-rw
Python library to read/write KiCad and LibrePCB Sexpr file format
159 parts9 - 2 layers109.3 × 45.4 mm

AVR BRIDGE ATMEGA328P
MCLEANS/AVR-BRIDGE-ATMEGA328P-PCB
PCB design for the AVR-BRIDGE ATMEGA328P test board
55 parts1 - 2 layers92.5 × 61.2 mm

Questions
How big is the Universal can board PCB?
It measures 49.5 × 111.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Universal can board use?
70 parts, built around the ATMEGA328P-AU, MCP2551-I/SN, FT232RL and LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Universal can board KiCad files?
From the franc0r/universal_can_board repository on GitHub, at the commit this page was made from: the board is board/universal-can-board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Universal can board design in my own project?
Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).