
MCP2551-I/SN
Microchip TechnologyExtended
-40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver SOIC-8 CAN Transceivers ROHS
- Part id
- microchip/MCP2551-I/SN
- Category
- CAN Transceivers
- Package
- SOIC-8
- Pins
- 8
- In stock
- 7,963 at JLCPCB (C49558)
- Used on
- 54 open-source boards
Overview
The MCP2551-I/SN is a CAN Transceiver made by Microchip Technology in a SOIC-8 package with 8 pins. -40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver SOIC-8 CAN Transceivers ROHS.
PCBKit's library has its KiCad symbol (dk_Interface-Drivers-Receivers-Transceivers:MCP2551-I_SN, from Digikey) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 7,963 are in stock at JLCPCB (part C49558). 54 open-source boards in 44 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
10- Supply, least
- 4.5 V · VDD, recommended operating min, Industrial (I) · p. 9
- Supply, most
- 5.5 V · VDD, recommended operating max, Industrial (I) · p. 9
- Supply, absolute maximum
- 7 V · VDD, absolute max · p. 8
- Works from
- -40 °C · Industrial (I) operating ambient min · p. 9
- Works up to
- 85 °C · Industrial (I) operating ambient max · p. 9
- Junction, hottest
- 150 °C · Virtual junction temperature absolute max · p. 8
- Takes working
- 10 mA · VDD supply current max, Recessive; VTXD = +2V; RS = 47 kW · p. 9
- Takes at most
- 75 mA · VDD supply current max, Dominant; VTXD = 0.8V · p. 9
- Takes asleep
- 365 µA · VDD standby supply current max, -40°C to +85°C · p. 9
- Data rate, most
- 1 Mbit/s · CAN operation max · p. 1
What it is and has
10- CAN data rate
- 1 Mb/s · p. 1
- Physical layer standard
- ISO-11898 · p. 1
- System compatibility
- 12V and 24V systems · p. 1
- Protection
- Power-on Reset and voltage brown-out protection · p. 1
- Protection
- High-voltage transient protection · p. 1
- Protection
- Automatic thermal shutdown · p. 1
- Maximum nodes
- 112 · p. 1
- Standby
- Low current standby operation · p. 1
- Industrial temperature range
- -40°C to +85°C · p. 1
- Package options
- PDIP/SOIC · p. 1
Specifications
58| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VDD VDD | max 7 V | 8 | |
| DC Voltage at TXD, RXD, VREF and VS | Maximum: VDD + 0.3V | min -0.3 V | 8 |
| DC Voltage at CANH, CANL (Note 1) | Short-circuit applied when TXD is High and Low. | min -42 · max 42 V | 8 |
| Transient Voltage on Pins 6 and 7 (Note 2) | In accordance with ISO-7637. | min -250 · max 250 V | 8 |
| Storage temperature | min -55 · max 150 °C | 8 | |
| Operating ambient temperature | Absolute maximum rating; Industrial operating specifications are limited to +85°C. | min -40 · max 125 °C | 8 |
| Virtual Junction Temperature, TVJ (Note 3) TVJ | In accordance with IEC 60747-1. | min -40 · max 150 °C | 8 |
| Soldering temperature of leads (10 seconds) | 10 seconds | max 300 °C | 8 |
| ESD protection on CANH and CANL pins (Note 4) | Classification A: Human Body Model. | max 6 kV | 8 |
| ESD protection on all other pins (Note 4) | Classification A: Human Body Model. | max 4 kV | 8 |
| Supply Current IDD | Dominant; VTXD = 0.8V; VDD | max 75 mA | 9 |
| Supply Current IDD | Recessive; VTXD = +2V; RS = 47 kW | max 10 mA | 9 |
| Supply Current IDD | -40°C ≤ TAMB ≤ +85°C, Standby; Note 2: ITXD = IRXD = IVREF = 0 mA; 0V < VCANL < VDD; 0V < VCANH < VDD; VRS = VDD. | max 365 uA | 9 |
| High-level of the Power-on Reset comparator VPORH | CANH, CANL outputs are active when VDD > VPORH | min 3.8 · max 4.3 V | 9 |
| Low-level of the Power-on Reset comparator VPORL | CANH, CANL outputs are not active when VDD < VPORL | min 3.4 · max 4 V | 9 |
| Hysteresis of Power-on Reset comparator VPORD | Note 1: periodically sampled and not 100% tested. | min 0.3 · max 0.8 V | 9 |
| CANH, CANL Recessive bus voltage VCANH(r); VCANL(r) | VTXD = VDD; no load. | min 2 · max 3 V | 9 |
| Recessive output current IO(CANH)(reces); IO(CANL)(reces) | -2V < V(CAHL,CANH) < +7V, 0V <VDD < 5.5V | min -2 · max 2 mA | 9 |
| Recessive output current IO(CANH)(reces); IO(CANL)(reces) | -5V < V(CANL,CANH) < +40V, 0V <VDD < 5.5V | min -10 · max 10 mA | 9 |
| CANH Dominant output voltage VO(CANH) | VTXD = 0.8V | min 2.75 · max 4.5 V | 9 |
| CANL Dominant output voltage VO(CANL) | VTXD = 0.8V | min 0.5 · max 2.25 V | 9 |
| Recessive differential output voltage VDIFF(r)(o) | VTXD = 2V; no load | min -500 · max 50 mV | 9 |
| Dominant differential output voltage VDIFF(d)(o) | VTXD = 0.8V; VDD = 5V; 40W < RL < 60W; Note 2. | min 1.5 · max 3 V | 9 |
| CANH short-circuit output current IO(SC)(CANH) | VCANH = -5V | max -200 mA | 9 |
| CANH short-circuit output current IO(SC)(CANH) | VCANH = -40V, +40V. Note 1: periodically sampled and not 100% tested. | typ -100 mA | 9 |
| CANL short-circuit output current IO(SC)(CANL)l | VCANL = -40V, +40V. Note 1: periodically sampled and not 100% tested. | max 200 mA | 9 |
| Recessive differential input voltage VDIFF(r)(i) | -2V < V(CANL, CANH) < +7V; receiver in High-speed, Slope-control and Standby modes. | min -1 · max 0.5 V | 9 |
| Recessive differential input voltage VDIFF(r)(i) | -12V < V(CANL, CANH) < +12V; receiver in High-speed, Slope-control and Standby modes. | min -1 · max 0.4 V | 9 |
| Dominant differential input voltage VDIFF(d)(i) | TXD = 2V; pins 6 and 7 externally driven; -2V < V(CANL, CANH) < +7V; Note 3. | min 0.9 · max 5 V | 10 |
| Dominant differential input voltage VDIFF(d)(i) | TXD = 2V; pins 6 and 7 externally driven; -12V < V(CANL, CANH) < +12V; Note 3. | min 1 · max 5 V | 10 |
| Differential input hysteresis VDIFF(h)(i) | TXD = 2V; pins 6 and 7 externally driven; See Figure 2-3; Note 1. | min 100 · max 200 mV | 10 |
| CANH, CANL Common-mode input resistance RIN | TXD = 2V; pins 6 and 7 externally driven | min 5 · max 50 kW | 10 |
| Deviation between CANH and CANL Common-mode input resistance RIN(d) | TXD = 2V; pins 6 and 7 externally driven; VCANH = VCANL | min -3 · max 3 % | 10 |
| Differential input resistance RDIFF | TXD = 2V; pins 6 and 7 externally driven | min 20 · max 100 kW | 10 |
| CANH, CANL input leakage current ILI | TXD = 2V; pins 6 and 7 externally driven; VDD < VPOR; VCANH = VCANL = +5V | max 150 uA | 10 |
| High-level input voltage VIH | TXD; Output Recessive; maximum VDD | min 2 V | 10 |
| Low-level input voltage VIL | TXD; Output Dominant; minimum VSS | max 0.8 V | 10 |
| High-level input current IIH | TXD; VTXD = VDD | min -1 · max 1 uA | 10 |
| Low-level input current IIL | TXD; VTXD = 0V | min -100 · max -400 uA | 10 |
| Low-level output voltage VOL | RXD; IOL = 8 mA | max 0.8 V | 10 |
| Slope-control mode current ISLOPE | RS pin | min -10 · max -200 uA | 10 |
| Shutdown junction temperature TJ(sd) | Note 1: periodically sampled and not 100% tested. | min 155 · max 180 o C | 10 |
| Shutdown temperature hysteresis TJ(h) | -12V < V(CANL, CANH) < +12V; Note 3. | min 20 · max 30 o C | 10 |
| Bit time tBIT | VRS = 0V | min 1 · max 62.5 us | 12 |
| Bit frequency fBIT | VRS = 0V | min 16 · max 1000 kHz | 12 |
| Delay TXD to bus active TtxL2bus(d) | -40°C ≤ TAMB ≤ +125°C, VRS = 0V | max 70 ns | 12 |
| Delay TXD to bus inactive TtxH2bus(r) | -40°C ≤ TAMB ≤ +85°C, VRS = 0V | max 125 ns | 12 |
| Delay TXD to receive active TtxL2rx(d) | -40°C ≤ TAMB ≤ +125°C, VRS = 0V | max 130 ns | 12 |
| Delay TXD to receive active TtxL2rx(d) | -40°C ≤ TAMB ≤ +125°C, RS = 47 kΩ | max 250 ns | 12 |
| Delay TXD to receiver inactive TtxH2rx(r) | -40°C ≤ TAMB ≤ +85°C, VRS = 0V | max 175 ns | 12 |
| Delay TXD to receiver inactive TtxH2rx(r) | -40°C ≤ TAMB ≤ +85°C, RS = 47 kΩ | max 225 ns | 12 |
| CANH, CANL slew rate SR | Refer to Figure 2-1; RS = 47 kΩ; Note 1. | min 5.5 · max 8.5 V/us | 12 |
| Wake-up time from standby (Rs pin) tWAKE | See Figure 2-5 | max 5 us | 12 |
| Bus Dominant to RXD Low (Standby mode) TbusD2rx(s) | VRS = +4V; See Figure 2-6 | max 550 ns | 12 |
| CANH; CANL input capacitance CIN(CANH); CIN(CANL) | 1 Mb/s data rate; VTXD = VDD; Note 1: periodically sampled and not 100% tested. | typ 20 pF | 12 |
| Differential input capacitance CDIFF | 1 Mb/s data rate; Note 1: periodically sampled and not 100% tested. | typ 10 pF | 12 |
| TX Permanent Dominant Timer Disable Time TtxL2busZ | min 1.25 · max 4 ms | 12 | |
| TX Permanent Dominant Timer Reset Time TtxR2pdt(res) | Rising edge on TXD while device is in permanent Dominant state | max 1 us | 12 |
Pins, by the datasheet
8- 1 TXD
- Transmit Data Input; TTL-compatible, with an internal pull-up to VDD. Low drives Dominant and High requests Recessive. · p. 5
- 2 VSS
- Ground supply pin. · p. 5
- 3 VDD
- Positive supply voltage pin. · p. 5
- 4 RXD
- Receive Data Output; CMOS-compatible, High when the CAN bus is Recessive and Low when Dominant. · p. 5
- 5 VREF
- Reference Voltage Output, defined as VDD/2. · p. 5
- 6 CANL
- CAN Low-Level Voltage I/O; drives the low side of the differential bus and connects internally to the receive comparator. · p. 5
- 7 CANH
- CAN High-Level Voltage I/O; drives the high side of the differential bus and connects internally to the receive comparator. · p. 5
- 8 RS
- Slope-Control Input; selects High-Speed, Slope-Control or Standby modes via an external biasing resistor. · p. 5
- 2 layers68 × 31 mm

- 4 layers83.4 × 68.5 mm

Ms3
pggood/Megasquirt-MS3-Bootloader
Bootloader to initialise MS3 if you need to replace the HCS12
82 parts7 - 2 layers109 × 95 mm

- 2 layers140 × 178.7 mm

- 2 layers256.5 × 172.9 mm

- 2 layers239.3 × 121.3 mm

- 2 layers35.1 × 62.7 mm

EMO SN65 OBD
darshanram008/EMO_OBD_tool
On board diagnostic tool for Battery management system
116 parts1 - 4 layers137.2 × 61.6 mm

Parts like it
8TJA1051T/3/1J
SOIC-8-150mil-40℃~+150℃ 110mA 4.5V~5.5V 5Mbps CAN FD Transceiver SOIC-8-150mil CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversSN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTJA1042T/1J
SOIC-8-40℃~+150℃ 15uA 4.5V~5.5V 5Mbps 70mA CAN FD Transceiver SOIC-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversCA-IF1051S
SOIC-8-55℃~+150℃ 2Mbps 4.5V~5.5V 80mA CAN Transceiver SOIC-8 CAN Transceivers ROHSChipanalogCAN TransceiversTJA1042T/3/1J
SOIC-8-40℃~+150℃ 15uA 4.5V~5.5V 5Mbps 70mA SOIC-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversTJA1044T/1Z
SOIC-8-40℃~+150℃ 15uA 1Mbit/s 4.5V~5.5V 60mA CAN Transceiver SOIC-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversSIT1050T
SO-8-40℃~+125℃ 1 10mA 1Mbps 4.5V~5.5V 70mA CAN Transceiver TXD dominant timeout、Thermal shutdown protection、Short-Circuit Protection、Silent mode SO-8 CAN Transceivers ROHSSITCAN TransceiversSN65HVD232D
SOIC-8-40℃~+85℃ 17mA 1Mbps 3.3V CAN Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
Questions
Is there a KiCad symbol and footprint for the MCP2551-I/SN?
Yes. The symbol is dk_Interface-Drivers-Receivers-Transceivers:MCP2551-I_SN and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the MCP2551-I/SN?
SOIC-8, with 8 pins. Its footprint is drawn on this page.
Where is the MCP2551-I/SN datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the MCP2551-I/SN?
JLCPCB lists it as part C49558, with 7,963 in stock; the sellers' links on this page open their listings.
What can replace the MCP2551-I/SN?
Parts like it in the library: the TJA1051T/3/1J by NXP Semiconductors, the SN65HVD230D by Texas Instruments, the TJA1042T/1J by NXP Semiconductors and the CA-IF1051S by Chipanalog. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the MCP2551-I/SN?
54 boards in 44 repositories on GitHub; the most starred are listed on this page, with their KiCad files.