
MCP2515-I/ST
Microchip TechnologyExtended
-40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI TSSOP-20 CAN Controllers ROHS
- Part id
- microchip/MCP2515-I/ST
- Category
- CAN Controllers
- Package
- TSSOP-20
- Pins
- 20
- In stock
- 19,907 at JLCPCB (C185941)
- Used on
- 11 open-source boards
Overview
The MCP2515-I/ST is a CAN Controller made by Microchip Technology in a TSSOP-20 package with 20 pins. -40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI TSSOP-20 CAN Controllers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:MCP2515T-E_ST, from EasyEDA) and its footprint (Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm, from KiCad's library), ready for a KiCad board. 19,907 are in stock at JLCPCB (part C185941). 11 open-source boards in 10 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
11- Supply, least
- 2.7 V · VDD, recommended operating min, Industrial (I) · p. 72
- Supply, most
- 5.5 V · VDD, recommended operating max, Industrial (I) · p. 72
- Supply, absolute maximum
- 7 V · VDD, absolute max · p. 71
- Works from
- -40 °C · Ambient operating min, Industrial (I) · p. 72
- Works up to
- 85 °C · Ambient operating max, Industrial (I) · p. 72
- Takes working
- 5 mA · VDD, active current typical · p. 1
- Takes at most
- 10 mA · VDD, operating current max at 5.5 V, FOSC = 25 MHz, FCLK = 1 MHz · p. 72
- Takes asleep
- 1 µA · VDD, Sleep mode standby current typical · p. 1
- Data rate, most
- 1 Mbit/s · CAN V2.0B bit rate max · p. 1
- Takes working
- 10 mA · Operating max, VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO open · p. 72
- Takes asleep
- 5 µA · Sleep max, inputs tied to VDD or VSS, -40°C to +85°C · p. 72
What it is and has
8- CAN
- V2.0B, 1 Mb/s · p. 1
- Acceptance filters
- Six 29-bit filters · p. 1
- Acceptance masks
- Two 29-bit masks · p. 1
- SPI
- 10 MHz · p. 1
- SPI modes
- 0,0 and 1,1 · p. 1
- Controller
- Stand-Alone CAN Controller with SPI Interface · p. 1
- CAN
- CAN V2.0B at 1 Mb/s · p. 1
- CAN data field
- 0 – 8 bytes · p. 1
Around it
1- res 1 k to 10 k
- between RESET and capacitor C; R1 limits current from the external reset capacitor during RESET pin breakdown. · p. 57
Specifications
68| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| VDD VDD | max 7 V | 71 | |
| All inputs and outputs w.r.t. VSS | min -0.6 V | 71 | |
| Storage temperature | min -65 · max 150 °C | 71 | |
| Ambient temperature with power applied | min -65 · max 125 °C | 71 | |
| Soldering temperature of leads | 10 seconds | max 300 °C | 71 |
| Supply Voltage VDD | Industrial (I) | min 2.7 · max 5.5 V | 72 |
| Register Retention Voltage VRET | Industrial (I) | min 2.4 V | 72 |
| High-Level Input Voltage VIH | RXCAN; Industrial (I) | min 2 V | 72 |
| Low-Level Input Voltage VIL | RXCAN, TXnRTS Pins; Industrial (I) | min -0.3 V | 72 |
| Low-Level Input Voltage VIL | SCK, CS, SI; Industrial (I) | min -0.3 V | 72 |
| Low-Level Output Voltage VOL | TXCAN; IOL = +6.0 mA, VDD = 4.5V; Industrial (I) | max 0.6 V | 72 |
| Low-Level Output Voltage VOL | RXnBF Pins; IOL = +8.5 mA, VDD = 4.5V; Industrial (I) | max 0.6 V | 72 |
| Low-Level Output Voltage VOL | SO, CLKOUT; IOL = +2.1 mA, VDD = 4.5V; Industrial (I) | max 0.6 V | 72 |
| Low-Level Output Voltage VOL | INT; IOL = +1.6 mA, VDD = 4.5V; Industrial (I) | max 0.6 V | 72 |
| Input Leakage Current ILI | All I/O except OSC1 and TXnRTS pins; CS = RESET = VDD, VIN = VSS to VDD; Industrial (I) | min -1 · max 1 uA | 72 |
| Input Leakage Current ILI | OSC1 Pin; Industrial (I) | min -5 · max 5 uA | 72 |
| Internal Capacitance (All Inputs and Outputs) CINT | TAMB = 25°C, fC = 1.0 MHz, VDD = 0V (Note 1); Industrial (I) | max 7 pF | 72 |
| Operating Current IDD | VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Open; Industrial (I) | max 10 mA | 72 |
| Standby Current (Sleep mode) IDDS | CS, TXnRTS = VDD, Inputs tied to VDD or VSS, -40°C TO +85°C; Industrial (I) | max 5 uA | 72 |
| Clock-In Frequency FOSC | 4.5V to 5.5V; Industrial (I) | min 1 · max 40 MHz | 73 |
| Clock-In Frequency FOSC | 2.7V to 5.5V; Industrial (I) | min 1 · max 25 MHz | 73 |
| Clock-In Period TOSC | 4.5V to 5.5V; Industrial (I) | min 25 · max 1000 ns | 73 |
| Clock-In Period TOSC | 2.7V to 5.5V; Industrial (I) | min 40 · max 1000 ns | 73 |
| Duty Cycle (External Clock Input) TDUTY | TOSH/(TOSH + TOSL); Industrial (I) | min 0.45 · max 0.55 — | 73 |
| Wake-up Noise Filter TWF | Industrial (I) | min 100 ns | 73 |
| RESET Pin Low Time trl | Industrial (I) | min 2 us | 73 |
| CLKOUT Pin High Time thCLKOUT | TOSC = 40 ns (Note 1); Industrial (I) | min 15 ns | 74 |
| CLKOUT Pin Low Time tlCLKOUT | TOSC = 40 ns (Note 1); Industrial (I) | min 15 ns | 74 |
| CLKOUT Pin Rise Time trCLKOUT | Measured from 0.3 VDD to 0.7 VDD (Note 1); Industrial (I) | max 5 ns | 74 |
| CLKOUT Pin Fall Time tfCLKOUT | Measured from 0.7 VDD to 0.3 VDD (Note 1); Industrial (I) | max 5 ns | 74 |
| CLOCKOUT Propagation Delay tdCLKOUT | Note 1; Industrial (I) | max 100 ns | 74 |
| Clock Frequency FCLK | Industrial (I) | max 10 MHz | 75 |
| CS Setup Time TCSS | Industrial (I) | min 50 ns | 75 |
| CS Hold Time TCSH | Industrial (I) | min 50 ns | 75 |
| CS Disable Time TCSD | Industrial (I) | min 50 ns | 75 |
| Data Setup Time TSU | Industrial (I) | min 10 ns | 75 |
| Data Hold Time THD | Industrial (I) | min 10 ns | 75 |
| CLK Rise Time TR | Note 1; Industrial (I) | max 2 us | 75 |
| CLK Fall Time TF | Note 1; Industrial (I) | max 2 us | 75 |
| Clock High Time THI | Industrial (I) | min 45 ns | 75 |
| Clock Low Time TLO | Industrial (I) | min 45 ns | 75 |
| Clock Delay Time TCLD | Industrial (I) | min 50 ns | 75 |
| Clock Enable Time TCLE | Industrial (I) | min 50 ns | 75 |
| Output Valid from Clock Low TV | Industrial (I) | max 45 ns | 75 |
| Output Hold Time THO | Industrial (I) | min 0 ns | 75 |
| Output Disable Time TDIS | Industrial (I) | max 100 ns | 75 |
| All inputs and outputs w.r.t. VSS | Maximum: VDD +1.0V | min -0.6 V | 71 |
| Soldering temperature of leads (10 seconds) | 10 seconds | max 300 °C | 71 |
| High-Level Input Voltage VIH | RXCAN; maximum VDD + 1 | min 2 V | 72 |
| Low-Level Input Voltage VIL | RXCAN, TXnRTS Pins; maximum .15 VDD | min -0.3 V | 72 |
| Low-Level Input Voltage VIL | SCK, CS, SI; maximum 0.4 VDD | min -0.3 V | 72 |
| Low-Level Output Voltage VOL | TXCAN; IOL = +6.0 mA, VDD = 4.5V | max 0.6 V | 72 |
| Low-Level Output Voltage VOL | RXnBF Pins; IOL = +8.5 mA, VDD = 4.5V | max 0.6 V | 72 |
| Low-Level Output Voltage VOL | SO, CLKOUT; IOL = +2.1 mA, VDD = 4.5V | max 0.6 V | 72 |
| Low-Level Output Voltage VOL | INT; IOL = +1.6 mA, VDD = 4.5V | max 0.6 V | 72 |
| Input Leakage Current ILI | All I/O except OSC1 and TXnRTS pins; CS = RESET = VDD, VIN = VSS to VDD | min -1 · max 1 uA | 72 |
| Input Leakage Current ILI | OSC1 Pin | min -5 · max 5 uA | 72 |
| Internal Capacitance (All Inputs and Outputs) CINT | TAMB = 25°C, fC = 1.0 MHz, VDD = 0V (Note 1) | max 7 pF | 72 |
| Operating Current IDD | VDD = 5.5V, FOSC = 25 MHz, FCLK = 1 MHz, SO = Open | max 10 mA | 72 |
| Standby Current (Sleep mode) IDDS | CS, TXnRTS = VDD, Inputs tied to VDD or VSS, -40°C TO +85°C | max 5 uA | 72 |
| Duty Cycle (External Clock Input) TDUTY | TOSH/(TOSH + TOSL) | min 0.45 · max 0.55 — | 73 |
| CLKOUT Pin High Time thCLKOUT | TOSC = 40 ns (Note 1) | min 15 ns | 74 |
| CLKOUT Pin Low Time tlCLKOUT | TOSC = 40 ns (Note 1) | min 15 ns | 74 |
| CLKOUT Pin Rise Time trCLKOUT | Measured from 0.3 VDD to 0.7 VDD (Note 1) | max 5 ns | 74 |
| CLKOUT Pin Fall Time tfCLKOUT | Measured from 0.7 VDD to 0.3 VDD (Note 1) | max 5 ns | 74 |
| CLOCKOUT Propagation Delay tdCLKOUT | Note 1 | max 100 ns | 74 |
| CLK Rise Time TR | Note 1 | max 2 us | 75 |
| CLK Fall Time TF | Note 1 | max 2 us | 75 |
- 2 layers75 × 41.5 mm

- 4 layers137.2 × 61.6 mm

- 2 layers49.5 × 111.8 mm

Universal can board
franc0r/universal_can_board
Contains schematic, pcb layout and software of the francor's universal can board.
70 partsBSD-3-Clause - 4 layers128.4 × 70.8 mm

VCU3.0
Obili69/E-GoCart
Vehicle Control Unit (VCU) firmware for an electric go-kart, built on ESP32-S3 with FreeRTOS. Manages motor control, battery management, charging, telemetry, and safety systems over dual CAN buses.
109 parts - 4 layers70 × 35 mm

- 2 layers157 × 58.5 mm

- 2 layers84.4 × 56.8 mm

RPi Hat
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
131 parts4Apache-2.0 - 2 layers99 × 85 mm

Sensactpi
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
124 parts4Apache-2.0
Parts like it
8XL2515-TSS
TSSOP-20-40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI Single transmission mode、Low-power mode TSSOP-20 CAN Controllers ROHSXINLUDACAN ControllersMCP2515-I
TSSOP-20-40℃~+85℃ 1Mbps 1uA 2.7V~5.5V 5mA CAN Controller SPI TSSOP-20 CAN Controllers ROHSTokmasCAN ControllersMCP2515-E/ST
TSSOP-20-40℃~+125℃ 1Mbps 2.7V~5.5V 5mA CAN Controller TSSOP-20 CAN Controllers ROHSMicrochip TechnologyCAN ControllersMCP2510-I/ST
TSSOP-20-40℃~+85℃ 1Mbps 3V~5.5V 5mA CAN Controller TSSOP-20 CAN Controllers ROHSMicrochip TechnologyCAN ControllersMCP2515T-E/ST-TUDI
TSSOP-20-40℃~+125℃ 1Mbps 2.7V~5.5V 5mA CAN Controller Programmable bit timing、Bus status monitoring、Single transmission mode TSSOP-20 CAN Controllers ROHSTudiCAN ControllersCH9431T
TSSOP-20TSSOP-20 CAN Controllers ROHSWCH (Nanjing Qinheng Microelectronics)CAN ControllersMCP2515T-I/ST-HX
TSSOP20TSSOP20 CAN Controllers ROHSZHHXDZCAN ControllersHX2515-ST
TSSOP-20CAN ControllersZHHXDZ
Questions
Is there a KiCad symbol and footprint for the MCP2515-I/ST?
Yes. The symbol is EasyEDA_Cloud:MCP2515T-E_ST and the footprint Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the MCP2515-I/ST?
TSSOP-20, with 20 pins. Its footprint is drawn on this page.
Where is the MCP2515-I/ST datasheet?
Microchip Technology publishes it: the Datasheet link on this page opens it.
Where can I order the MCP2515-I/ST?
JLCPCB lists it as part C185941, with 19,907 in stock; the sellers' links on this page open their listings.
What can replace the MCP2515-I/ST?
Parts like it in the library: the XL2515-TSS by XINLUDA, the MCP2515-I by Tokmas, the MCP2515-E/ST by Microchip Technology and the MCP2510-I/ST by Microchip Technology. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the MCP2515-I/ST?
11 boards in 10 repositories on GitHub; the most starred are listed on this page, with their KiCad files.