
Mintypcb
jackw01/pi-tin
Open source raspberry pi handheld retro gaming console

Schaltplan is an open-source printed circuit board by michaelgr22, from the michaelgr22/can-to-go-system repository on GitHub. It is a 2-layer board of 72 × 138 mm with 39 parts on 54 nets, routed with 260 tracks and 27 vias.
It is built around the ESP32-DEVKITC-32UE, PCA9306DCTR and B3FS-1010P. Its parts include 17 resistors, 5 diodes, 4 capacitors, 3 ICs and 3 connectors. It belongs with the ESP32 boards of this library.
Portable device to stream CAN messages on an App or Browser.




| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R4, R5, R9, R10, R11 |
| 5 | 270 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R15, R16, R17, R18 |
| 5 | LED | LED:LED_OF-SMD3528WC | D3, D4, D5, D6, D7 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12, R13, R14 |
| 3 | B3FS-1010P | Button:SW_B3FS-1010P | S3, S4, S5 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C14 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C15 |
| 1 | 120R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 200k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R19 |
| 1 | 3-106505-2 | Stecker:TE_3-106505-2 | J1 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | ESP32-DEVKITC-32U | ESP:MODULE_ESP32-DEVKITC-32U | U3 |
| 1 | MCP2562-E-SN | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | PCA9306DCTR | Level_Shifter:SOP65P400X130-8N | U5 |
The 35 most common of 39 parts.

jackw01/pi-tin
Open source raspberry pi handheld retro gaming console

Karpova-Lab/pyControl-D-Series-Breakout
A breakout board for use with pyControl behavior control framework

SophBG/pi-tin-mod
Personal build of jackw01's Pi Tin (3D-printed clamshell version, KiCad 10). It adds 10 RGB LEDs under the buttons, a centred speaker, a USB-drive mode for the ROMs, and ESD protection on USB, and runs on an Orange Pi…

danieltith/Neuroscience
Code and hardware files related to my PhD thesis: "Mapping associations between early life adversity and alcohol use disorder through human epidemiology and rat neurobiology".


kyledenobel/RGA_Boards
PCB Board design and development for RGA (Recording Guitar Amplifier)


doppelgrau/esp32-f9p-io-board
An IO-PCB (two motor-driver/H-bridge, CAN, RS232, ADS1115, relay, ethernet, ardusimple f9p compatible connector) with an ESP32 for 12V power, three 15V tolerant analog inputs, three 5V tolerant inputs.
It measures 72 × 138 mm and has 2 copper layers, 1.6 mm thick.
39 parts, built around the ESP32-DEVKITC-32UE, PCA9306DCTR and B3FS-1010P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the michaelgr22/can-to-go-system repository on GitHub, at the commit this page was made from: the board is Hardware/Schaltplan_KiCad/Schaltplan.kicad_pcb and its schematic Hardware/Schaltplan_KiCad/Schaltplan.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask michaelgr22 before reusing the design.