6 layers57 × 25.9 mm
R7FS7MOD
Brazil-L/Lumeward-OpenSource
Open-source Lumeward firmware and development tools
228 parts2Apache-2.0
4 layers95 × 67 mm
LoRaDongle iCE40
marrrk/LoRaDongle4A Risc-V Based LoRa custom PCB
- Size
- 95 × 67 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 145
- Nets
- 126
- Pads
- 496
- Tracks, vias
- 1,261, 217
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 21 Jul 2021
- Updated
- 7 Feb 2023
Overview
LoRaDongle iCE40 is an open-source printed circuit board by marrrk, from the marrrk/LoRaDongle repository on GitHub. It is a 4-layer board of 95 × 67 mm with 145 parts on 126 nets, routed with 1,261 tracks and 217 vias.
It is built around the ICE40UP5K-SG48ITR50, SKY13587-378LF and SX1261IMLTRT, with the RP550K001A-TR, SGP40-D-R4 and W25Q128JVSIQ among its other parts. Its parts include 57 capacitors, 27 resistors, 9 connectors, 9 inductors and 8 ICs. It belongs with the radio and wireless and home automation and IoT boards and the FPGA and CPLD boards of this library.
Main components
12
ICE40UP5K-SG48ITR50
QFN-48QFN-48 Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)
SKY13587-378LF
XFDFN-6(1x1)-40℃~+105℃ 0.65dB 1.8V~5V 20MHz~6GHz 22dB 30dBm SPDT XFDFN-6(1x1) RF Switches ROHSSkyworks SolutionsRF Switches
SX1261IMLTRT
QFN-24-EP(4x4)-148dBm -40℃~+85℃ 1.8V~3.7V 150MHz~960MHz 15dBm 15mA 300Kbps 4.2mA ISM SPI Supports software reset、Power-on reset function、Supports RSSI function transceiver QFN-24-EP(4x4) RF Transceiver ICs ROHSSEMTECHRF Transceiver ICs
RP550K001A-TR
DFN(PLP)2730-12-40℃~+85℃ 1.7A 2 2.3V~5.5V 2MHz~2.5MHz 45uA 600mV~3.3V Adjustable Buck Buck Built-in Yes DFN(PLP)2730-12 DC-DC Converters ROHSNisshinbo Micro Devices Inc.DC-DC Converters
SGP40-D-R4
DFN-6-EP(2.4x2.4)-10℃~+50℃ 0.85mm 0.8mm 0ppm~1000ppm 1.7V~3.6V 2.44mm 2.44mm 2.6mA Air quality I2C Reset function DFN-6-EP(2.4x2.4) VOC Sensors ROHSSensirionVOC Sensors
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
93LC56BT-I/OT
SOT-23-6-40℃~+85℃ 1,000,000 cycles 2.5V~5.5V 200 Years 2Kbit 2MHz 6ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) SPI SOT-23-6 EEPROM ROHSMicrochip TechnologyEEPROM
FT2232HL
QFP64Dual High Speed USB to Multipurpose UART/FIFO ICFTDIUncategorised
RMCF0402FT10K0
0402-55℃~+155℃ 10kΩ 63mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSStackpole Electronics (SEI)Chip Resistor - Surface MountRMCF0402FT100R
0402-55℃~+155℃ 100Ω 50V 63mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSStackpole Electronics (SEI)Chip Resistor - Surface MountRMCF0402JT100K
0402-55℃~+155℃ 100kΩ 50V 63mW Thick Film Resistor ±100ppm/℃ ±5% 0402 Chip Resistor - Surface Mount ROHSStackpole Electronics (SEI)Chip Resistor - Surface Mount
BLM18AG601SN1D
0603-55℃~+125℃ 1 380mΩ 500mA 600Ω@100MHz ±25% 0603 Ferrite Beads ROHSMurataFerrite Beads
README
README.mdLoRaDongle
LoRaDongle is a custom PCB that merges Risc-V with LoRa in a USB Dongle form factor. This repository contains all the project files required to build, utilise and modify the project. Documentation can be read from the site: https://marrrk.github.io/LoRaDongle/
Cloning the repository
git clone --recurse-submodules https://github.com/marrrk/LoRaDongle.gitDirectory Structure
- PCB/ - Contains the Kicad project files, schematics, gerbers, BOM and other PCB related files
- SOC/ - The python scripts that generate, build and load the Risc-V SoC onto the PCB
- firmware/ - SUpporting firmware that runs on the SoC
- docs/ - Source files for the documentation website
License Licensed under CERN-OHL-P v2 permissive variant or later.
Parts
145| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C8, C9, C10, C12, C13, C16, C18, C19, C20, C21, C22 |
| 11 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C23, C24, C25, C26, C27, C29, C30, C31, C32, C33, C57 |
| 11 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10, R13, R14, R15, R16, R17, R22, R23, R24, R25, R27 |
| 5 | 100R | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R18, R19, R20, R21 |
| 5 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C28, C34, C54, C55, C56 |
| 3 | 100K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6, R7 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C4, C6 |
| 3 | 22pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C3, C5, C47 |
| 3 | 4.7uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C7, C11, C17 |
| 3 | 470pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C39, C40, C44 |
| 3 | 600R/0.5A | digikey-footprints:0603 | FB1, FB2, FB3 |
| 3 | SolderJumper_2_Open | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | JP1, JP2, JP3 |
| 2 | 1.8pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C36, C37 |
| 2 | 10R | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2 |
| 2 | 2.2uH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1, L2 |
| 2 | 27pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C14, C15 |
| 2 | 3.3pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C48, C50 |
| 2 | 33pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C41, C43 |
| 2 | 47nH | Inductor_SMD:L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L3, L6 |
| 2 | 9.1nH | Inductor_SMD:L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L7, L9 |
| 2 | GND | TestPoint:TestPoint_Pad_D2.5mm | GND1, GND2 |
| 2 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1, SW2 |
| 1 | 1.2V | TestPoint:TestPoint_Pad_D2.5mm | 1V2 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C35 |
| 1 | 12K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11 |
| 1 | 12pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C52 |
| 1 | 142-0701-801 | digikey-footprints:RF_SMA_BoardEdge_142-0701-801 | J5 |
| 1 | 15uH | KiCad_VLS201610CX-150M-1:VLS2016 | L5 |
| 1 | 18nH | Inductor_SMD:L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L4 |
| 1 | 1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R8 |
| 1 | 1pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C38 |
| 1 | 2.7nH | Inductor_SMD:L_0402_1005Metric_Pad0.77x0.64mm_HandSolder | L8 |
| 1 | 2K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R9 |
| 1 | 2k2 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R12 |
| 1 | 3.3V | TestPoint:TestPoint_Pad_D2.5mm | 3V3 |
| 1 | 3.3uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C53 |
| 1 | 3pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C49 |
| 1 | 4.7 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R26 |
| 1 | 453K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 1 | 470nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C42 |
| 1 | 47nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C45 |
| 1 | 47pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C46 |
| 1 | 5V | TestPoint:TestPoint_Pad_D2.5mm | 5V1 |
| 1 | 6.8pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C51 |
| 1 | 93LC56BT-I_OT | 93LC56B-I_OT_KiCad:SOT95P270X145-6N | IC1 |
| 1 | CTL2 | TestPoint:TestPoint_Pad_D2.5mm | CTL2 |
| 1 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Conn_01x08_Male | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x10_Male | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J2 |
| 1 | Conn_01x17_Male | Connector_PinHeader_2.54mm:PinHeader_1x17_P2.54mm_Vertical | J9 |
| 1 | Conn_02x02_Top_Bottom | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J6 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y2 |
| 1 | Crystal_GND24_Small | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Done | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | ECS-2520MV-500-BL-TR | Oscillator:Oscillator_SMD_ECS_2520MV-xxx-xx-4Pin_2.5x2.0mm | X1 |
| 1 | FT2232HL | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | ICE40UP5K-SG48ITR | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U6 |
| 1 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | LOGO | Logo:license2 | G*** |
| 1 | LOGO | Logo:qr_code | G*** |
| 1 | LOGO | Logo:mark_njoroge | G3 |
| 1 | LOGO | Logo:LoRaDongleLogo | G1 |
| 1 | LOGO | Logo:rev2 | G*** |
| 1 | OSCI | TestPoint:TestPoint_Pad_D2.5mm | OSCI1 |
| 1 | OSCO | TestPoint:TestPoint_Pad_D2.5mm | OSCO1 |
| 1 | PWR | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | RP550K001A-TR | RP550K001A-TR_KiCad:SON50P270X300X60-13N | U1 |
| 1 | RX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D4 |
| 1 | SGP40-D-R4 | KiCad_SGP40-D-R4:SON80P244X244X95-7N | IC3 |
| 1 | SKY13587-378LF | SW_SKYA21012:SW_SKYA21012 | U4 |
| 1 | SX1261IMLTRT | sx1261-footprint:Semtech-QFN24-0-0-0 | U3 |
| 1 | TX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | USB_A | Connector_USB:USB_A_CNCTech_1001-011-01101_Horizontal | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U5 |
| 1 | XTA | TestPoint:TestPoint_Pad_D2.5mm | XTA1 |
| 1 | XTB | TestPoint:TestPoint_Pad_D2.5mm | XTB1 |
| 1 | iCE_CLK | TestPoint:TestPoint_Pad_D2.5mm | iCE_CLK1 |
| 1 | iCE_SI | TestPoint:TestPoint_Pad_D2.5mm | iCE_SI1 |
| 1 | iCE_SO | TestPoint:TestPoint_Pad_D2.5mm | iCE_SO1 |
The 143 most common of 145 parts.
Questions
How big is the LoRaDongle iCE40 PCB?
It measures 95 × 67 mm and has 4 copper layers, 1.6 mm thick.
What parts does the LoRaDongle iCE40 use?
145 parts, built around the ICE40UP5K-SG48ITR50, SKY13587-378LF, SX1261IMLTRT and RP550K001A-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LoRaDongle iCE40 KiCad files?
From the marrrk/LoRaDongle repository on GitHub, at the commit this page was made from: the board is PCB/LoRaDongle_iCE40_USB/LoRaDongle_iCE40.kicad_pcb and its schematic PCB/LoRaDongle_iCE40_USB/LoRaDongle_iCE40.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the LoRaDongle iCE40 design in my own project?
Its repository states no licence, so its author keeps all rights: ask marrrk before reusing the design.
Similar boards
- 6 layers60.6 × 100 mm
Gecko5education
logisim-evolution/GECKO5Education
Openhardware educational platform based on the ideas of the ulx3s and Gecko4Education
311 parts18MIT - 4 layers40 × 17.6 mm
- 4 layers150 × 120 mm
Ephys test board
open-ephys/ephys-test-board
General purpose, automated electrophysiology test board
567 parts1 - 2 layers
- 4 layers
Lora node
Mehdi-Ldj/lora-ble-sensor-node
Off-grid LoRa/BLE sensor node — 868 MHz LoRa, 2.4 GHz BLE, solar/LiFePO4
110 partsCERN-OHL-P-2.0 - 4 layers58.4 × 36.8 mm
Quadcopter FCU
upadhyaydhruv/vajra-quadcopter
Custom quadcopter firmware written in STM32 HAL
33 partsMIT - 2 layers44.4 × 22 mm
NRF52840-FART V3
tomasmcguinness/zigbee-nrf-flow-and-return-temperature-sensor
A zigbee based, dual probe temperature sensor designed to operate on battery.
9 parts20