SGP40-D-R4

Sensirion

-10℃~+50℃ 0.85mm 0.8mm 0ppm~1000ppm 1.7V~3.6V 2.44mm 2.44mm 2.6mA Air quality I2C Reset function DFN-6-EP(2.4x2.4) VOC Sensors ROHS

Extended

Datasheetsensirion/SGP40-D-R4

Category: VOC Sensors
Package: DFN-6-EP(2.4x2.4)
Pins: 7

Overview

The SGP40-D-R4 is a VOC Sensor made by Sensirion in a DFN-6-EP(2.4x2.4) package with 7 pins. -10℃~+50℃ 0.85mm 0.8mm 0ppm~1000ppm 1.7V~3.6V 2.44mm 2.44mm 2.6mA Air quality I2C Reset function DFN-6-EP(2.4x2.4) VOC Sensors ROHS.

PCBKit's library has its KiCad symbol (SparkFun-Sensors:SGP40, from Eagle libraries) and its footprint (SparkFun-Sensors:SGP40, from Eagle libraries), ready for a KiCad board. 1,882 are in stock at JLCPCB (part C2874215). 19 open-source boards in 16 repositories on GitHub use it.

Symbol

SparkFun-Sensors:SGP40From Eagle libraries

Footprint

SparkFun-Sensors:SGP40From Eagle libraries

From the datasheet

Supply, least: 1.7 V · VDD, VDDH, recommended operating min · p. 5
Supply, most: 3.6 V · VDD, VDDH, recommended operating max · p. 5
Supply, absolute maximum: 3.6 V · VDD, absolute max · p. 7
Works from: -10 °C · Recommended operating ambient min · p. 6
Works up to: 50 °C · Recommended operating ambient max · p. 6
Takes working: 3.5 mA · Typical total supply current, continuous operation at 1.8 V · p. 5
Takes working: 2.6 mA · Typical total supply current, continuous operation at 3.3 V · p. 5
Takes asleep: 34 µA · Typical idle current after power-up, heater-off command or soft reset · p. 5

What it is and has

Sensing technology: MOx gas sensor for indoor air quality · p. 1
Interface: I2C with digital output · p. 1
Package: 6-pin DFN, 2.44 x 2.44 x 0.85 mm3 · p. 1
Packaging: Tape and reel, reflow solderable · p. 1
I2C address: 89 decimal, 0x59 · p. 11
I2C modes: Standard-mode and fast-mode, up to 400 kHz · p. 11
Compliance: RoHS, REACH, Halogen-free, WEEE · p. 8

Around it

cap 1 F: between VDDH and VSS; Recommended hotplate supply decoupling; required decoupling depends on the supply network. · p. 7
res 10 k: between SDA and VDD; Example pull-up value; size for bus capacitance and communication frequency. · p. 7

Specifications

Parameter	Conditions	As printed	Page
Supply voltage, hotplate supply voltage VDD, VDDH	25 °C; VDD and VDDH connected to the same power supply	min 1.7 · typ 3.3 · max 3.6 V	5
Idle current IDD	25 °C, 3.3 V; after power-up, sgp4x_turn_heater_off command or soft reset	typ 34 · max 105 A	5
Supply current under operation	25 °C; continuously operated at VDD, VDDH = 1.8 V; average current	typ 3.5 · max 4 mA	5
Supply current under operation	25 °C; continuously operated at VDD, VDDH = 3.3 V; average current	typ 2.6 · max 3 mA	5
Power-up time tPU	After hard reset, VDD ≥ VPOR	typ 0.4 · max 0.6 ms	5
Soft reset time tSR	After soft reset	typ 0.4 · max 0.6 ms	5
SCL clock frequency fSCL		max 400 kHz	5
Relative humidity	Operating conditions	min 0 · max 90 % RH	6
Temperature	Operating conditions	min -10 · max 50 °C	6
Humidity	Operating conditions of humidity compensation; dew points −13 °C and +31 °C at minimum and maximum temperature, respectively; limited also to 90 % RH, whichever is smaller	min 1.5 · max 30 g m−3 (°C dew point)	6
Humidity	Operating conditions of humidity compensation; the smaller of this and the absolute humidity limit	max 90 % RH	6
Temperature	Operating conditions of humidity compensation	min -10 · max 50 °C	6
Relative humidity	Storage conditions	min 0 · max 80 % RH	6
Temperature	Storage conditions	min 5 · max 30 °C	6
Supply voltage VDD VDD		min -0.3 · max 3.6 V	7
Supply voltage VDDH VDDH		min -0.3 · max 3.6 V	7
Short-term storage temperature range	Temporary conditions during, e.g., transport	min -40 · max 70 °C	7
Operating temperature range		min -20 · max 55 °C	7
Short-term storage humidity range	Non-condensing; temporary conditions during, e.g., transport	min 0 · max 80 %	7
Operating humidity range	Non-condensing	min 0 · max 90 %	7
ESD HBM		max 2 kV	7
ESD CDM		max 500 V	7
Latch up, JESD78 Class II, 125 °C	JESD78 Class II, 125 °C	max 100 mA	7

Pins, by the datasheet

1 VDD: Supply voltage; requires RC decoupling. · p. 7
2 VSS: Ground. · p. 7
3 SDA: Serial data. · p. 7
4 n/a: Connect to ground; no electrical function. · p. 7
5 VDDH: Hotplate supply voltage; connect to the same supply as VDD. · p. 7
6 SCL: Serial clock. · p. 7

Parameters

Current - Supply: 3.5mA
Height: 0.85mm
Interface: I2C
Length: 2.44mm
Measurement Range: 0ppm~1000ppm
Operating Temperature: -10℃~+50℃
Standby Current: 34uA
Voltage - Supply: 1.7V~3.6V
Voltage - Supply(Absolute Max): 3.6V

Order codes

SGP40-D-R4LCSC C2874215

Pinout

The pins of the SGP40-D-R4
Pin	Name	Type
1	VDD	Power in
2	GND	Power in
3	SDA	Unspecified
4	GND	Power in
5	VDDH	Power in
6	SCL	Unspecified
DIEPAD	GND	Power in

Open-source boards using it

All 19

2 layers25.1 × 25.2 mm
Mini Environmental Sensor
MbFredys/PCB-Mini-Environmental-Sensor
Compact ESP32-C3 environmental-sensor PCB design using BME280 and SGP40 for temperature, humidity, pressure, and VOC-based air-quality sensing.
34 parts14
4 layers95 × 67 mm
LoRaDongle iCE40
marrrk/LoRaDongle
A Risc-V Based LoRa custom PCB
145 parts4
2 layers44.7 × 93.6 mm
Ultisense
darshg321/Ultisense
an esp32-s3 devboard made to sense as many things as possible
94 parts3
4 layers74 × 56 mm
Atmos
HearnChristian/atmos-sense
ESP32-based atmospheric sensing node: BME280 environmental sensing and AS3935 lightning detection over I2C, designed for drone integration. KiCad hardware plus firmware.
73 parts1MIT
2 layers60 × 40 mm
AMUN
Summanuss/openairqmonitor
Open source hardware to monitor temperature, humidity and VOC in an indoor environment
47 parts1Apache-2.0
4 layers47.1 × 45.3 mm
Mixed signal Board Rev D
Akhilesh-design-02/STM32F407-Hardware-Design
4-layer STM32F407 mixed-signal PCB design featuring I2C/I2S/USB interfaces, SGP40 & SHT40 sensors, power plane splits, and star grounding for noise isolation.
92 parts
4 layers50.8 × 22.9 mm
Weather Feather Wing
benjamincrockett/Weather-Feather-Wing
A circuit board incorporating temperature, humidity, atmospheric pressure, and CO2 sensors into an Adafruit Feather Wing form factor with Stemma QT connectors.
35 parts
4 layers112 × 100 mm
Ai05-env sensors
leafony/ai05-env-sensors
全センサーは Leafony Bus の 3.3 V・I²C に接続します。基板は 23 × 20 mm、4層、板厚 0.8 mm です。
252 parts

Show this part on your page

A live frame, for any web page

<iframe src="https://pcbkit.io/embed/parts/sensirion/SGP40-D-R4" title="SGP40-D-R4 in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>

A picture

<img src="https://pcbkit.io/embed/parts/sensirion/SGP40-D-R4.jpg" alt="SGP40-D-R4" width="1200" height="900">

A picture that opens the part, for a README

[![SGP40-D-R4](https://pcbkit.io/embed/parts/sensirion/SGP40-D-R4.jpg?size=s)](https://pcbkit.io/parts/sensirion/SGP40-D-R4)

Questions

Is there a KiCad symbol and footprint for the SGP40-D-R4?

Yes. The symbol is SparkFun-Sensors:SGP40 and the footprint SparkFun-Sensors:SGP40, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the SGP40-D-R4?

DFN-6-EP(2.4x2.4), with 7 pins. Its footprint is drawn on this page.

Where is the SGP40-D-R4 datasheet?

Sensirion publishes it: the Datasheet link on this page opens it.

Where can I order the SGP40-D-R4?

JLCPCB lists it as part C2874215, with 1,882 in stock; the sellers' links on this page open their listings.

Which open-source boards use the SGP40-D-R4?

19 boards in 16 repositories on GitHub; the most starred are listed on this page, with their KiCad files.